A kind of adjustable external fixation device for lower extremity is designed. The circuit is mainly composed of TEC1-00703 semiconductor refrigeration chip, HZC-30A pressure sensor, STC89C52RC single chip microcomputer and other electrical components. It can realize the timing intelligent temperature control and meet the local fixed-point refrigeration. The design of adjustable structure and the application of intelligent air cushion can satisfy the full fixation of lower limbs of different individuals. Its operation does not need much medical knowledge. It can solve the problem of emergency transportation and follow-up treatment of lower limb injury in ice and snow sports. It has a good application prospect and universality.
External Fixators ; Fracture Fixation ; Humans ; Lower Extremity ; Refrigeration ; Semiconductors

New technological advances have paved the way for significant progress in automated urinalysis. Quantitative reading of urinary test strips using reflectometry has become possible, while complementary metal oxide semiconductor (CMOS) technology has enhanced analytical sensitivity and shown promise in microalbuminuria testing. Microscopy-based urine particle analysis has greatly progressed over the past decades, enabling high throughput in clinical laboratories. Urinary flow cytometry is an alternative for automated microscopy, and more thorough analysis of flow cytometric data has enabled rapid differentiation of urinary microorganisms. Integration of dilution parameters (e.g., creatinine, specific gravity, and conductivity) in urine test strip readers and urine particle flow cytometers enables correction for urinary dilution, which improves result interpretation. Automated urinalysis can be used for urinary tract screening and for diagnosing and monitoring a broad variety of nephrological and urological conditions; newer applications show promising results for early detection of urothelial cancer. Concomitantly, the introduction of matrix-assisted laser desorption ionization-time-of-flight mass spectrometry (MALDI-TOF MS) has enabled fast identification of urinary pathogens. Automation and workflow simplification have led to mechanical integration of test strip readers and particle analysis in urinalysis. As the information obtained by urinalysis is complex, the introduction of expert systems may further reduce analytical errors and improve the quality of sediment and test strip analysis. With the introduction of laboratory-on-a-chip approaches and the use of microfluidics, new affordable applications for quantitative urinalysis and readout on cell phones may become available. In this review, we present the main recent developments in automated urinalysis and future perspectives.
Automation ; Cell Phones ; Creatinine ; Expert Systems ; Flow Cytometry ; Mass Screening ; Mass Spectrometry ; Microfluidics ; Microscopy ; Semiconductors ; Specific Gravity ; Urinalysis* ; Urinary Tract ; Urinary Tract Infections

BACKGROUND: The photolithography process in the semiconductor industry uses various chemicals with little information on their constitution. This study aimed to identify the chemical constituents of photoresist (PR) products and their by-products and to compare these constituents with material safety data sheets (MSDSs) and analytical results. METHODS: A total of 51 PRs with 48 MSDSs were collected. Analysis consisted of two parts: First, the constituents of the chemical products were identified and analyzed using MSDS data; second, for verification of the by-products of PR, volatile organic compounds were analyzed. The chemical constituents were categorized according to hazards. RESULTS: Forty-five of 48 products contained trade secrets in amounts ranging from 1 to 65%. A total of 238 ingredients with multiple counting (35 ingredients without multiple counting) were identified in the MSDS data, and 48.7% of ingredients were labeled as trade secrets under the Korea Occupational Safety and Health Act. The concordance rate between the MSDS data and the analytical result was 41.7%. The by-product analysis identified 129 chemicals classified according to Chemical Abstracts Service No., with 17 chemicals that are carcinogenic, mutagenic, and reprotoxic substances. Formaldehyde was found to be released from 12 of 21 products that use novolak resin. CONCLUSION: We confirmed that several PRs contain carcinogens, and some were not specified in the toxicological information in the MSDS. Hazardous chemicals, including benzene and formaldehyde, are released from PRs products as by-products. Therefore, it is necessary to establish a systematic management system for chemical compounds and the working environment.
Benzene ; Carcinogens ; Constitution and Bylaws ; Formaldehyde ; Hazardous Substances ; Korea ; Material Safety Data Sheets ; Occupational Health ; Semiconductors ; Volatile Organic Compounds

BACKGROUND: The aim of this study was to describe the types of diseases that developed in semiconductor workers who have registered with the Korea Workers' Compensation and Welfare Service (KWCWS) and to identify potential common occupational characteristics by the type of claimed disease. METHODS: A total of 55 semiconductor workers with cancer or rare diseases who claimed to the KWCWS were compared based on their work characteristics and types of claimed diseases. Leukemia, non-Hodgkin lymphoma, and aplastic anemia were grouped into lymphohematopoietic (LHP) disorder. RESULTS: Leukemia (n = 14) and breast cancer (n = 10) were the most common complaints, followed by brain cancer (n = 6), aplastic anemia (n = 6), and non-Hodgkin lymphoma (n = 4). LHP disorders (n = 24) accounted for 43%. Sixty percent (n = 33) of registered workers (n = 55) were found to have been employed before 2000. Seventy-six percent (n = 42) of registered workers and 79% (n = 19) among the registered workers with LHP (n = 24) were found to be diagnosed at a relatively young age, ≤40 years. A total of 18 workers among the registered semiconductor workers were finally determined to deserve compensation for occupational disease by either the KWCWS (n = 10) or the administrative court (n = 8). Eleven fabrication workers who were compensated responded as having handled wafers smaller than eight inches in size. Eight among the 18 workers compensated (44 %) were found to have ever worked at etching operations. CONCLUSION: The distribution of cancer and rare diseases among registered semiconductor workers was closely related to the manufacturing era before 2005, ≤8 inches of wafer size handled, exposure to clean rooms of fabrication and chip assembly operations, and etching operations.
Anemia, Aplastic ; Brain Neoplasms ; Breast Neoplasms ; Compensation and Redress ; Environment, Controlled ; Korea ; Leukemia ; Lymphoma, Non-Hodgkin ; Occupational Diseases ; Rare Diseases ; Semiconductors ; Workers' Compensation

OBJECTIVES: The Samsung Ombudsperson Commission was launched as an independent third-party institution following an agreement among Samsung Electronics, Supporters for Health and Right of People in Semiconductor Industry (Banolim in Korean, an independent NGO), and the Family Compensation Committee, in accordance with the industry accident prevention measure required by the settlement committee to address the issues related to employees who allegedly died from leukemia and other diseases as a result of working at Samsung's semiconductor production facilities. METHODS: The Commission has carried out a comprehensive range of activities to review and evaluate the status of the company's occupational accidents management system, as well as occupational safety and health risk management within its facilities. RESULTS: Based on the results of this review, termed a comprehensive diagnosis, the Commission presented action plans for improvement to strengthen the company's existing safety and health management system and to effectively address uncertain risks in this area going forward. CONCLUSIONS: The Commission will monitor the execution of the suggested tasks and provide advice and guidance to ensure that Samsung's semiconductor and liquid crystal display production lines are safer.
Accident Prevention ; Accidents, Occupational ; Compensation and Redress ; Diagnosis ; Humans ; Korea ; Leukemia ; Liquid Crystals ; Occupational Diseases ; Occupational Health ; Risk Management ; Semiconductors

This article aims to provide a systematic review of the exposure assessment methods used to assign wafer fabrication (fab) workers in epidemiologic cohort studies of mortality from all causes and various cancers. Epidemiologic and exposure–assessment studies of silicon wafer fab operations in the semiconductor industry were collected through an extensive literature review of articles reported until 2017. The studies found various outcomes possibly linked to fab operations, but a clear association with the chemicals in the process was not found, possibly because of exposure assessment methodology. No study used a tiered assessment approach to identify similar exposure groups that incorporated manufacturing era, facility, fab environment, operation, job and level of exposure to individual hazardous agents. Further epidemiologic studies of fab workers are warranted with more refined exposure assessment methods incorporating both operation and job titleand hazardous agents to examine the associations with cancer risk or mortality.
Cohort Studies ; Epidemiologic Studies ; Methods* ; Mortality ; Retrospective Studies* ; Semiconductors* ; Silicon

For prompt gamma ray imaging for biomedical applications and environmental radiation monitoring, we propose herein a multiple-scattering Compton camera (MSCC). MSCC consists of three or more semiconductor layers with good energy resolution, and has potential for simultaneous detection and differentiation of multiple radio-isotopes based on the measured energies, as well as three-dimensional (3D) imaging of the radio-isotope distribution. In this study, we developed an analytic simulator and a 3D image generator for a MSCC, including the physical models of the radiation source emission and detection processes that can be utilized for geometry and performance prediction prior to the construction of a real system. The analytic simulator for a MSCC records coincidence detections of successive interactions in multiple detector layers. In the successive interaction processes, the emission direction of the incident gamma ray, the scattering angle, and the changed traveling path after the Compton scattering interaction in each detector, were determined by a conical surface uniform random number generator (RNG), and by a Klein-Nishina RNG. The 3D image generator has two functions: the recovery of the initial source energy spectrum and the 3D spatial distribution of the source. We evaluated the analytic simulator and image generator with two different energetic point radiation sources (Cs-137 and Co-60) and with an MSCC comprising three detector layers. The recovered initial energies of the incident radiations were well differentiated from the generated MSCC events. Correspondingly, we could obtain a multi-tracer image that combined the two differentiated images. The developed analytic simulator in this study emulated the randomness of the detection process of a multiple-scattering Compton camera, including the inherent degradation factors of the detectors, such as the limited spatial and energy resolutions. The Doppler-broadening effect owing to the momentum distribution of electrons in Compton scattering was not considered in the detection process because most interested isotopes for biomedical and environmental applications have high energies that are less sensitive to Doppler broadening. The analytic simulator and image generator for MSCC can be utilized to determine the optimal geometrical parameters, such as the distances between detectors and detector size, thus affecting the imaging performance of the Compton camera prior to the development of a real system.
Clothing ; Gamma Rays* ; Isotopes ; Radiation Monitoring ; Semiconductors

BACKGROUND: We examined the feasibility of a full-length gene analysis for the drug resistance-related genes inhA, katG, rpoB, pncA, rpsL, embB, eis, and gyrA using ion semiconductor next-generation sequencing (NGS) and compared the results with those obtained from conventional phenotypic drug susceptibility testing (DST) in multidrug-resistant Mycobacterium tuberculosis (MDR-TB) isolates. METHODS: We extracted genomic DNA from 30 pure MDR-TB isolates with antibiotic susceptibility profiles confirmed by phenotypic DST for isoniazid (INH), rifampin (RIF), ethambutol (EMB), pyrazinamide (PZA), amikacin (AMK), kanamycin (KM), streptomycin (SM), and fluoroquinolones (FQs) including ofloxacin, moxifloxacin, and levofloxacin. Enriched ion spheres were loaded onto Ion PI Chip v3, with 30 samples on a chip per sequencing run, and Ion Torrent sequencing was conducted using the Ion AmpliSeq TB panel (Life Technologies, USA). RESULTS: The genotypic DST results revealed good agreement with the phenotypic DST results for EMB (Kappa 0.8), PZA (0.734), SM (0.769), and FQ (0.783). Agreements for INH, RIF, and AMK+KM were not estimated because all isolates were phenotypically resistant to INH and RIF, and all isolates were phenotypically and genotypically susceptible to AMK+KM. Moreover, 17 novel variants were identified: six (p.Gly169Ser, p.Ala256Thr, p.Ser383Pro, p.Gln439Arg, p.Tyr597Cys, p.Thr625Ala) in katG, one (p.Tyr113Phe) in inhA, five (p.Val170Phe, p.Thr400Ala, p.Met434Val, p.Glu812Gly, p.Phe971Leu) in rpoB, two (p.Tyr319Asp and p.His1002Arg) in embB, and three (p.Cys14Gly, p.Asp63Ala, p.Gly162Ser) in pncA. CONCLUSIONS: Ion semiconductor NGS could detect reported and novel amino acid changes in full coding regions of eight drug resistance-related genes. However, genotypic DST should be complemented and validated by phenotypic DSTs.
Amikacin ; Clinical Coding ; Complement System Proteins ; DNA ; Drug Resistance* ; Ethambutol ; Fluoroquinolones ; Isoniazid ; Kanamycin ; Levofloxacin ; Mycobacterium tuberculosis* ; Mycobacterium* ; Ofloxacin ; Pyrazinamide ; Rifampin ; Semiconductors* ; Streptomycin

PURPOSE: This study evaluated the radiopacity of contemporary luting cements using conventional and digital radiography. MATERIALS AND METHODS: Disc specimens (N=24, n=6 per group, ø7 mm×1 mm) were prepared using 4 resin-based luting cements (Duolink, Multilink N, Panavia F 2.0, and U-cem). The specimens were radiographed using films, a complementary metal oxide semiconductor (CMOS) sensor, and a photostimulable phosphor plate (PSP) with a 10-step aluminum step wedge (1 mm incremental steps) and a 1-mm-thick tooth cut. The settings were 70 kVp, 4 mA, and 30 cm, with an exposure time of 0.2 s for the films and 0.1 s for the CMOS sensor and PSP. The films were scanned using a scanner. The radiopacity of the luting cements and tooth was measured using a densitometer for the film and NIH ImageJ software for the images obtained from the CMOS sensor, PSP, and scanned films. The data were analyzed using the Kruskal-Wallis and Mann-Whitney U tests. RESULTS: Multilink (3.44–4.33) showed the highest radiopacity, followed by U-cem (1.81–2.88), Panavia F 2.0 (1.51–2.69), and Duolink (1.48–2.59). The R² values of the optical density of the aluminum step wedge were 0.9923 for the films, 0.9989 for the PSP, 0.9986 for the scanned films, and 0.9266 for the CMOS sensor in the linear regression models. CONCLUSION: The radiopacities of the luting materials were greater than those of aluminum or dentin at the same thickness. PSP is recommended as a detector for radiopacity measurements because of its accuracy and convenience.
Aluminum ; Dental Enamel ; Dental Materials ; Dentin ; Linear Models ; Radiographic Image Enhancement ; Radiography ; Semiconductors ; Tooth

BACKGROUND: This study investigated the relationship between job type and the risk for spontaneous abortion to assess the reproductive toxicity of female workers in the semiconductor industry. METHODS: A questionnaire survey was administered to current female workers of two semiconductor manufacturing plants in Korea. We included female workers who became pregnant at least 6 months after the start of their employment with the company. The pregnancy outcomes of 2,242 female workers who experienced 4,037 pregnancies were investigated. Personnel records were used to assign the subjects to one of three groups: fabrication process workers, packaging process workers, and clerical workers. To adjust for within-person correlations between pregnancies, a generalized estimating equation was used. The logistic regression analysis was limited to the first pregnancy after joining the company to satisfy the assumption of independence among pregnancies. Moreover, we stratified the analysis by time period (pregnancy in the years prior to 2008 vs. after 2009) to reflect differences in occupational exposure based on semiconductor production periods. RESULTS: The risk for spontaneous abortion in female semiconductor workers was not significantly higher for fabrication and packaging process workers than for clerical workers. However, when we stratified by time period, the odds ratio for spontaneous abortion was significantly higher for packaging process workers who became pregnant prior to 2008 when compared with clerical workers (odds ratio: 2.21; 95% confidence interval: 1.01–4.81). CONCLUSIONS: When examining the pregnancies of female semiconductor workers that occurred prior to 2008, packaging process workers showed a significantly higher risk for spontaneous abortions than did clerical workers. The two semiconductor production periods in our study (prior to 2008 vs. after 2009) had different automated processes, chemical exposure levels, and working environments. Thus, the conditions prior to 2008 may have increased the risk for spontaneous abortions in packaging process workers in the semiconductor industry. ELECTRONIC SUPPLEMENTARY MATERIAL: The online version of this article (10.1186/s40557-017-0204-x) contains supplementary material, which is available to authorized users.
Abortion, Spontaneous* ; Chemical Processes ; Clergy ; Employment ; Female ; Female* ; Humans ; Korea ; Logistic Models ; Occupational Exposure ; Odds Ratio ; Pregnancy ; Pregnancy Outcome ; Product Packaging ; Semiconductors*