Excessive wear of the teeth, which causes functional, aesthetic problems, or sensitivity symptoms, is referred to as pathological wear. If this leads to the collapse of occlusion, extensive restoration is necessary to restore function and aesthetics.When restoring pathologically worn dentition, it is essential to identify the cause of the wear before determining treatment plan to get a favorable prognosis. In this case, a patient exhibited severe tooth wear with decreased vertical dimension and clinical, radiographic examination, and medical history indicated the pathological wear caused by a combination of factors. Consequently, full-mouth rehabilitation was indicated and the vertical occlusal height was determined considering the appropriate restorative space. Based on the causes of the wear, the restoration method, materials, and occlusal pattern were selected and successfully restored to normal occlusal state through full-mouth rehabilitation with zirconia full-veneered crowns.

Purpose: . The purpose of this study is to analyze the biomechanical differences in rotation angle-torque according to the type of implant and to compare the effects of contamination and sandblasting on the removal torque value (RTV) of abutment screws. Materials and methods: . For this study, an automated device for tightening and loosening implant screws was developed, and each 15 implant-abutment complexes of external and internal connection type were prepared, divided into three groups according to the surface treatment of the screw:control group (no treatment), experimental group-1 (artificial saliva contamination and chlorhexidine (CHX) rinsing), and experimental group-2 (artificial saliva contamination, CHX rinsing, and subsequent 50 µm Al 2 O 3 sandblasting). FirstRTV was measured for each group, followed by different post-treatment procedures for the screws, and then Second-RTV was measured. During the procedure, the removal torque value and rotation angle vs. time were recorded at a 20 data/s.A standardized protocol was followed for all the tightening and loosening procedures: screw was tightened with 30 Ncm torque and maintained for 5 s, and then rotated in the reverse direction until the torque value reached 0 Ncm. After 10min of rest period, the screws were loosened to initial point. Results: . Statistical analysis of measured data revealed that the internal connection type showed significantly higher First-RTV compared to the external connection type, however, no significant differences in Second-RTV were found. Both experimental groups 1and 2 showed a decrease in RTVs for both implant types, while the control group showed a decrease in RTV only for the internal type. The internal connection type required a significantly larger rotation angle during the tightening and loosening process. Conclusion . Within the limitations of this study, both artificial saliva contamination and CHX cleansing, as well as sandblasting, decreased RTV in both internal and external connection types. Internal connections were more susceptible to the effects of contaminants.

The occlusal collapse resulting from loss of posterior tooth support and attrition necessitates treatment aimed at restoring normal function and aesthetics.Particularly in cases where there is insufficient space for restoration, full mouth rehabilitation accompanied by increased vertical dimension is necessary. This case report presents a complete mouth rehabilitation of a patient with inadequate anterior restoration space due to loss of posterior tooth support, utilizing guided implant surgery, facial scan, virtual articulator, and jaw motion tracker.

Background: s/Aims: While large-for-size syndrome is uncommon in liver transplantation (LT), it can result in fatal outcome. To prevent such fatality, we manufactured 3D-printed intra-abdominal cavity replicas to provide intuitive understanding of the sizes of the graft and the patient’s abdomen in patients with small body size between July 2020 and February 2022. Methods: Clinical outcomes were compared between patients using our 3D model during LT, and patients who underwent LT without 3D model by using 1 : 5 ratio propensity score-matched analysis. Results: After matching, a total of 20 patients using 3D-printed abdominal cavity model and 100 patients of the control group were included in this study. There were no significant differences in 30-day postoperative complication (50.0% vs. 64.0%, p = 0.356) and the incidence of large-for-size syndrome (0% vs. 7%, p = 0.599). Overall survival of the 3D-printed group was similar to that of the control group (p = 0.665), but graft survival was significantly superior in the 3D-printed group, compared to the control group (p = 0.034). Conclusions Since it showed better graft survival, as well as low cost and short production time, our 3D-printing protocol can be a feasible option for patients with small abdominal cavity to prevent large-for-size syndrome after LT.

Purpose: The purpose of this study was to determine the characteristics of patients with failed initial Kasai portoenterostomy (KP) and to compare the long-term prognosis of redo-KP with that of liver transplantation (LT) in these patients. Methods: The medical records of patients with biliary atresia (BA) who failed initial KP from 2010 to 2021 at a single center were retrospectively analyzed. KP failure was defined as persistent jaundice (total bilirubin concentration, ≥2.0 mg/dL) after KP or the performance of LT. Results: During the study period, 32 patients experienced initial KP failure, with 10 undergoing redo-KP and 22 undergoing LT. Redo-KP was successful in a minority of patients with failed initial KP, but the complications, particularly cholangitis, were more frequent in the redo-KP group. The long-term prognosis of redo-KP compared to LT showed that while some patients benefited from native liver survival after redo-KP, LT remains the more definitive solution for sustained liver function and survival in patients with BA. Conclusion The only factor differing significantly between patients who underwent redo-KP and LT after failed initial KP was complications of cholangitis. Redo-KP was successful in 4 of 10 patients with failed initial KP, suggesting that redo-KP may be a treatment option in patients with BA and failed initial KP.

Excessive wear of the teeth, which causes functional, aesthetic problems, or sensitivity symptoms, is referred to as pathological wear. If this leads to the collapse of occlusion, extensive restoration is necessary to restore function and aesthetics.When restoring pathologically worn dentition, it is essential to identify the cause of the wear before determining treatment plan to get a favorable prognosis. In this case, a patient exhibited severe tooth wear with decreased vertical dimension and clinical, radiographic examination, and medical history indicated the pathological wear caused by a combination of factors. Consequently, full-mouth rehabilitation was indicated and the vertical occlusal height was determined considering the appropriate restorative space. Based on the causes of the wear, the restoration method, materials, and occlusal pattern were selected and successfully restored to normal occlusal state through full-mouth rehabilitation with zirconia full-veneered crowns.

Purpose: . The purpose of this study is to analyze the biomechanical differences in rotation angle-torque according to the type of implant and to compare the effects of contamination and sandblasting on the removal torque value (RTV) of abutment screws. Materials and methods: . For this study, an automated device for tightening and loosening implant screws was developed, and each 15 implant-abutment complexes of external and internal connection type were prepared, divided into three groups according to the surface treatment of the screw:control group (no treatment), experimental group-1 (artificial saliva contamination and chlorhexidine (CHX) rinsing), and experimental group-2 (artificial saliva contamination, CHX rinsing, and subsequent 50 µm Al 2 O 3 sandblasting). FirstRTV was measured for each group, followed by different post-treatment procedures for the screws, and then Second-RTV was measured. During the procedure, the removal torque value and rotation angle vs. time were recorded at a 20 data/s.A standardized protocol was followed for all the tightening and loosening procedures: screw was tightened with 30 Ncm torque and maintained for 5 s, and then rotated in the reverse direction until the torque value reached 0 Ncm. After 10min of rest period, the screws were loosened to initial point. Results: . Statistical analysis of measured data revealed that the internal connection type showed significantly higher First-RTV compared to the external connection type, however, no significant differences in Second-RTV were found. Both experimental groups 1and 2 showed a decrease in RTVs for both implant types, while the control group showed a decrease in RTV only for the internal type. The internal connection type required a significantly larger rotation angle during the tightening and loosening process. Conclusion . Within the limitations of this study, both artificial saliva contamination and CHX cleansing, as well as sandblasting, decreased RTV in both internal and external connection types. Internal connections were more susceptible to the effects of contaminants.

The occlusal collapse resulting from loss of posterior tooth support and attrition necessitates treatment aimed at restoring normal function and aesthetics.Particularly in cases where there is insufficient space for restoration, full mouth rehabilitation accompanied by increased vertical dimension is necessary. This case report presents a complete mouth rehabilitation of a patient with inadequate anterior restoration space due to loss of posterior tooth support, utilizing guided implant surgery, facial scan, virtual articulator, and jaw motion tracker.

Excessive wear of the teeth, which causes functional, aesthetic problems, or sensitivity symptoms, is referred to as pathological wear. If this leads to the collapse of occlusion, extensive restoration is necessary to restore function and aesthetics.When restoring pathologically worn dentition, it is essential to identify the cause of the wear before determining treatment plan to get a favorable prognosis. In this case, a patient exhibited severe tooth wear with decreased vertical dimension and clinical, radiographic examination, and medical history indicated the pathological wear caused by a combination of factors. Consequently, full-mouth rehabilitation was indicated and the vertical occlusal height was determined considering the appropriate restorative space. Based on the causes of the wear, the restoration method, materials, and occlusal pattern were selected and successfully restored to normal occlusal state through full-mouth rehabilitation with zirconia full-veneered crowns.