Objective To analyze the influence of shaping on the bending strength of bone plates and the influence of different locking nail distributions on plate force to provide biomechanical references for shaping plates and selecting different locking nail distributions.Methods Finite element simulation analysis of the four-point bending strength of a plate was performed according to the YY/T 0342-2020 standard.Theoretical analysis and finite element simulation method were used to analyze the force on prosthesis models with different lock-nail distributions.Results At 30° bending,the 3.7 mm-thick plate had 28%higher equivalent plastic strain than the 2.7 mm-thick plate.The 3.7 and 2.7 mm-thick plates had ultimate bending angles of 55° and 67°,respectively.The crease had little impact on the plate stress.The four-point bending strength and equivalent bending stiffness of the unshapeed structure were 2.64 N·m and 1.12 N·m2,respectively.The four-point bending strength and equivalent bending stiffness with the crease were 2.63 N·m and 1.10 N·m2,respectively.After forward and backward bending,the four-point bending strength of the plate decreased from 2.64 to 2.45 N·m by approximately 7.72%,and the equivalent bending stiffness decreased from 1.12 to 0.98 N·m2 by approximately 12%.The impact was obvious.After implantation of tamponade screws,the four-point bending strength of the single-hole plate improved significantly from 2.64 to 3.15 N·m,by approximately 19.32%and the equivalent bending stiffness increased from 1.12 to 1.14 N·m2,by approximately 2.1%.At least two locking holes were reserved on both sides of the fracture line.Not inserting the locking screw reduced the stress by approximately 50%compared with the full insertion of the locking screw.During 15-week postoperative walking without bone callus formation,the material stress of TC4 reached 852.7 MPa and yielding occurred.Conclusions In a clinical scenario where larger shaping is required,it is not suitable for plates with larger thicknesses and plate fractures are more likely to occur after large-thickness shaping.This can guide the clinical selection of plates with appropriate thickness based on the shaping angle,and tamponade screws can be implanted in extreme cases.Fixing locking screws clinically is recommended;however,a method of fixing the locking screws with full screws is not recommended.The biomechanical effect is best when two locking holes at both ends of the fracture line are maintained without fixing the locking screws.

Objective: First-line bevacizumab plus carboplatin and paclitaxel (CP) is approved for stage III/IV ovarian cancer treatment following initial surgical resection, based on global phase III GOG-0218 and ICON7 trials. This study evaluated the efficacy and safety of bevacizumab + CP as first-line ovarian cancer therapy in Chinese patients. Methods: Patients with newly diagnosed, International Federation of Gynecology and Obstetrics (FIGO) stage III/IV epithelial ovarian, fallopian tube, or primary peritoneal cancer post-primary surgery were randomized 1:1 to receive 6 cycles of CP with bevacizumab/ placebo, followed by bevacizumab/placebo maintenance until unacceptable toxicity or disease progression. Primary endpoint was investigator-assessed progression-free survival (PFS). Stratification factors were FIGO stage and debulking status (stage III optimally debulked vs stage III suboptimally debulked vs stage IV) and Eastern Cooperative Oncology Group performance status (0 vs 1 or 2). Results: Of randomized patients, 51 received bevacizumab + CP and 49 received placebo + CP. Median PFS was 22.6 months with bevacizumab + CP (95% confidence interval [CI]=18.6, not estimable) and 12.3 months (95% CI=9.5, 15.0) with placebo + CP (stratified hazard ratio=0.30; 95% CI=0.17, 0.53). Treatment-related grade 3/4 adverse events occurred in 46 of 49 (94%) patients receiving bevacizumab + CP, and 34 of 50 (68%) receiving placebo + CP. Conclusion Bevacizumab + CP showed clinically meaningful improvement in PFS vs placebo + CP, consistent with GOG-0218 results. Safety data were aligned with the known bevacizumab safety profile. These results support first-line bevacizumab + CP therapy in Chinese patients with ovarian cancer.

Objective: First-line bevacizumab plus carboplatin and paclitaxel (CP) is approved for stage III/IV ovarian cancer treatment following initial surgical resection, based on global phase III GOG-0218 and ICON7 trials. This study evaluated the efficacy and safety of bevacizumab + CP as first-line ovarian cancer therapy in Chinese patients. Methods: Patients with newly diagnosed, International Federation of Gynecology and Obstetrics (FIGO) stage III/IV epithelial ovarian, fallopian tube, or primary peritoneal cancer post-primary surgery were randomized 1:1 to receive 6 cycles of CP with bevacizumab/ placebo, followed by bevacizumab/placebo maintenance until unacceptable toxicity or disease progression. Primary endpoint was investigator-assessed progression-free survival (PFS). Stratification factors were FIGO stage and debulking status (stage III optimally debulked vs stage III suboptimally debulked vs stage IV) and Eastern Cooperative Oncology Group performance status (0 vs 1 or 2). Results: Of randomized patients, 51 received bevacizumab + CP and 49 received placebo + CP. Median PFS was 22.6 months with bevacizumab + CP (95% confidence interval [CI]=18.6, not estimable) and 12.3 months (95% CI=9.5, 15.0) with placebo + CP (stratified hazard ratio=0.30; 95% CI=0.17, 0.53). Treatment-related grade 3/4 adverse events occurred in 46 of 49 (94%) patients receiving bevacizumab + CP, and 34 of 50 (68%) receiving placebo + CP. Conclusion Bevacizumab + CP showed clinically meaningful improvement in PFS vs placebo + CP, consistent with GOG-0218 results. Safety data were aligned with the known bevacizumab safety profile. These results support first-line bevacizumab + CP therapy in Chinese patients with ovarian cancer.

Objective: First-line bevacizumab plus carboplatin and paclitaxel (CP) is approved for stage III/IV ovarian cancer treatment following initial surgical resection, based on global phase III GOG-0218 and ICON7 trials. This study evaluated the efficacy and safety of bevacizumab + CP as first-line ovarian cancer therapy in Chinese patients. Methods: Patients with newly diagnosed, International Federation of Gynecology and Obstetrics (FIGO) stage III/IV epithelial ovarian, fallopian tube, or primary peritoneal cancer post-primary surgery were randomized 1:1 to receive 6 cycles of CP with bevacizumab/ placebo, followed by bevacizumab/placebo maintenance until unacceptable toxicity or disease progression. Primary endpoint was investigator-assessed progression-free survival (PFS). Stratification factors were FIGO stage and debulking status (stage III optimally debulked vs stage III suboptimally debulked vs stage IV) and Eastern Cooperative Oncology Group performance status (0 vs 1 or 2). Results: Of randomized patients, 51 received bevacizumab + CP and 49 received placebo + CP. Median PFS was 22.6 months with bevacizumab + CP (95% confidence interval [CI]=18.6, not estimable) and 12.3 months (95% CI=9.5, 15.0) with placebo + CP (stratified hazard ratio=0.30; 95% CI=0.17, 0.53). Treatment-related grade 3/4 adverse events occurred in 46 of 49 (94%) patients receiving bevacizumab + CP, and 34 of 50 (68%) receiving placebo + CP. Conclusion Bevacizumab + CP showed clinically meaningful improvement in PFS vs placebo + CP, consistent with GOG-0218 results. Safety data were aligned with the known bevacizumab safety profile. These results support first-line bevacizumab + CP therapy in Chinese patients with ovarian cancer.

ObjectiveTo validate the alleviating effect of Gegen Qinliantang （GGQLT） on insulin resistance in db/db diabetic mice by regulating the silent information regulator 1 （SIRT1）/forkhead transcription factor O1 （FoxO1） autophagy pathway. MethodSeventy-five SPF-grade spontaneous type 2 diabetic db/db mice and 15 control db/m mice were selected and maintained on regular feed for one week before measuring blood glucose. They were randomly divided into six groups， with 15 mice in each group. The groups included a normal group （physiological saline， 0.2 g·kg^-1）， a metformin group （0.2 g·kg^-1）， high-， medium-， and low-dose GGQLT groups （31.9， 19.1， 6.9 g·kg^-1）， and a model group （physiological saline， 0.2 g·kg^-1）. They were orally treated with corresponding drugs for eight weeks， once daily. Fasting blood glucose （FBG） was measured using a Roche glucometer. Serum levels of high-density lipoprotein cholesterol （HDL-C）， low-density lipoprotein cholesterol （LDL-C）， triglyceride （TG）， and total cholesterol （TC） were measured using an automated biochemical analyzer. Fasting serum insulin （INS） levels were determined using enzyme-linked immunosorbent assay （ELISA）， and the homeostasis model assessment of insulin resistance （HOMA-IR） was calculated. Western blot was used to detect the expression of Beclin-1， microtubule-associated protein 1 light chain 3 （LC3）， and SIRT1/FoxO1 autophagy pathway-related proteins in liver tissues. Immunohistochemistry was performed to assess the expression of SIRT1， FoxO1， Beclin-1， and LC3B proteins in liver tissues. Transmission electron microscopy was used to observe the formation of autophagosomes in the liver. ResultCompared with the normal group， the model group showed significant increases in FBG， FINS， HOMA-IR， TC， TG， LDL-C， and HDL-C levels （P<0.01）， and significant increases in the expression of SIRT1， Beclin-1， LC3， and FoxO1 proteins in liver tissues （P<0.01）. Transmission electron microscopy revealed the highest number of autophagosomes in the model group. Compared with the model group， the metformin group and the low-， medium-， and high-dose GGQLT groups showed significant decreases in serum FBG， FINS， HOMA-IR， TC， TG， LDL-C， and HDL-C levels （P<0.05， P<0.01）， significant decreases in the expression of SIRT1， Beclin-1， LC3 （P<0.05， P<0.01）， and up-regulated FoxO1 protein （P<0.01）. Transmission electron microscopy showed a reduction in the degree of autophagy in the treatment groups. Compared with the metformin group， the medium- and high-dose GGQLT groups showed significant decreases in FBG， FINS， and TG levels （P<0.01）， significant decreases in the expression of SIRT1， Beclin-1， and LC3 in liver tissues （P<0.05， P<0.01）， and reduced FoxO1 protein （P<0.01）. The high-dose GGQLT group showed reduced HOMA-IR， TC， LDL-C， and HDL-C levels （P<0.05， P<0.01）. Transmission electron microscopy revealed a significant reduction in autophagosomes in the medium- and high-dose GGQLT groups. ConclusionGGQLT can significantly improve glucose and lipid metabolism disorders， alleviate insulin resistance in db/db mice， and prevent and treat type 2 diabetes by activating the SIRT1/FoxO1 autophagy pathway.

Background::Dermatophagoides pteronyssinus is a common allergen causing allergic diseases in China. The aim of this study was to evaluate the efficacy and safety of D. pteronyssinus extracts produced by Peking Union Medical College Hospital (PUMCH) for the skin prick test (SPT) in the diagnosis of D. pteronyssinus allergy. Methods::A total of 910 subjects with allergic diseases were prescribed D. pteronyssinus SPT and specific sIgE (sIgE) test among the Outpatients of Department of Allergy, PUMCH from August 10, 2015 to August 30, 2017. Receiver operating characteristic curve (ROC) analysis was performed according to the results of D. pteronyssinus-sIgE detection. The accuracy of D. pteronyssinus extracts used for SPT in the diagnosis of D. pteronyssinus allergy was evaluated under different cutoff values. Adverse events after SPT were recorded to evaluate safety. Results::There were 796 and 618 subjects in the full analysis set (FAS) and the per protocol set (PPS), respectively. The areas under the curve of FAS and PPS were 0.871 and 0.873, respectively. According to the ROC of PPS, the optimal and 95% specificity diagnostic cutoff values of D. pteronyssinus SPT mean wheal diameter were 3.25 and 3.75 mm, respectively. No adverse events occurred. Conclusion::The extracts of D. pteronyssinus for SPT were simple, highly accurate, and safe and should be considered for recommendation in the clinical diagnosis of D. pteronyssinus allergy.

In 2013, Shanghai Medical College of Fudan University restarted the enrollment of the undergraduate students in directional pediatrics. To cultivate medical talents in pediatrics, a serious of educational innovations and practices have been carried out guided by competency training, including training a team of teachers with simulated teaching skills and establishing a teaching platform for simulation teaching. Medical students can practice medicine and gain experience through the risk-free simulated scenarios, that is helpful to enhance their confidence in clinical skills and communications and decrease medical errors in their future careers.

OBJECTIVE：To optimize the p reparation technology of citronellol submicroemulsion. METHODS ：The content of citronellol in Citronellol submicroemulsion was determined by HPLC. Citronellol submicroemulsion by high-speed shearing dispersion-high pressure homogenization method ，with centrifugation stability constant （ke） and particle size were used as evaluation indexes. Its formulation and preparation technology were optimized and validated. Drug-loading amount and encapsulation rate of the preparation were detected. RESULTS ：The linear range of citronellol were 4-64 μg/mL（R 2＝0.999 9）. RSDs of precision ，stability（24 h）and reproducibility tests were all lower than 3％. The recoveries were 97.64％-101.97％（RSD＝ 2.28％，n＝3），97.71％-99.50％（RSD＝1.29％，n＝3），96.87％-101.48％（RSD＝2.86％，n＝3）. The optimal formulation included that total weight of soybean oil and medium chain triglycerides （1 ∶ 1，g/g）was 3.75 g，1.2％ soybean phospholipid was 0.6 g， cholesterol was 0.06 g，citronellol was 1.25 g，0.6 ％ sodium oleate was 0.3 g，15-hydroxystearic acid polyethylene glycol ester was 0.75 g，poloxamer 188 was 0.75 g，water added to 50 mL. After prepared by optimal technology at 4 ℃ which contained shearing speed of 13 000 r/min，lasting for 5 min， primary emulsion was adjusted to pH 7 with dilute hydro- chloric acid ，and homogenized with 600 Bar high pressure for 1434412440@qq.com 5 min. The parameters of Citronellol submicroemulsion accor- ding to optimal formulation and technology contained mean particle size of （91.05±0.26）nm，PDI of （0.20±0.01）， Zeta-potential of （－30.86±0.39）mV，average content of 649511230@qq.com citronellol（100.21±0.01）％，the drug-loading amount was （2.481 7 ± 0.000 7） mg/mL，the encapsulation rate was （99.27 ± 0.03）％ . CONCLUSIONS ：The optimal formulation and technology is stable and feasible.

Objective To explore the value of axis shift between the baseline normal sinus rhythm (NSR) and WCT in diagnosis of wide QRS-complex tachycardia (WCT). Methods 390 surface ECGs of 186 patients with WCT were obtained from April 2012 to April 2018 at Ningbo Medical Center Lihuili Hospital at which the arrhythmia diagnosis was proven by intracardiac electrophysiological study. The axis shift between the baseline NSR and WCT was calculated by table lookup method. Then we analyzed the role of axis shift in diagnosis of WCT. Results Among the 186 patients with WCT, 147 (79.03％) were ventricular tachycardia (VT) , and 39 (20.97％) were supraventricual tachycardia (SVT) with conduction abnormalities. In the 95％ confidence interval, the axis shift showed an outstanding discrimination performance. The area under the ROC curve is 0.708 (0.579-0.817, P =0.007). Compared with left axis deviation, right axis deviation, the right axis deviation of LBBB morphology, the axis shift> 68 degree is more sensitive (53.06％) , and the specificity (91.43％) is also more desirable. Moreover, if the axis shift set> 130 degree, the specificity can reach 100％, and the sensitivity (12.24％) is equivalent to northwestern axis. Conclusion A significant axis shift between the baseline NRS and WCT can distinguish WCT accurately. Given the ease of grasping, it can probably be feasible to popularize as a routine diagnosis method for WCT in primary hospitals.

Objective: To study the correlation of occupation musculoskeletal disease (OMD) and safety behavior in assembly line workers. Methods: Selected assembly line workers of 3 manufacturing factory in Pacity as the objects of this study by judgement sampling. Questionnaires were used for messages collection including the general sociodemographic characteristic, OMD condition, occupational safety behaviors. Results: This study shows that, 826 OMD workers were found that the annual prevalence was 38.03%. The scores of work posture, handling habits, health habit in OMD group was lower than non-OMD group (P<0.01) but personal protection behavior was higher than non-OMD group (P<0.01) . Test of binary logistic regression revealed that age, workage, work posture, handling habits were the factors of OMD (P<0.01) . Conclusion Safety behaviors were the potent factors of OMD that work posture and handling habits should be broadcast.