ObjectiveThe widespread adoption of portable fundus cameras for primary care and community screening is hindered by limitations in current autofocus(AF) technologies. Image-based methods relying on sharpness evaluation require iterative searches, resulting in slow convergence, while projection-based techniques are susceptible to optical artifacts and calibration errors. To address these challenges, this study introduces a novel AF system based on direct wavefront sensing, designed to deliver simultaneous high speed, high precision, and operational robustness within the compact form factor essential for portable ophthalmic devices. MethodsOur approach fundamentally reimagines the AF process by directly measuring the ocular wavefront aberration. We developed a custom portable fundus camera integrating a miniaturized Shack-Hartmann wavefront sensor (SHWS) into the optical path. An 850 nm laser diode projects a point source onto the retina via oblique illumination to minimize corneal reflections. Light scattered from this spot carries the eye’s refractive error through the imaging optics and is directed to the SHWS, positioned at a plane optically conjugate to the primary color CMOS imaging sensor. A microlens array within the SHWS samples the incident wavefront, generating a pattern of focal spots on a CCD. Real-time centroid analysis of these spots provides a map of local wavefront slopes. These measurements are processed through a singular value decomposition (SVD) algorithm to fit a Zernike polynomial basis set, enabling real-time reconstruction of the wavefront phase. The defocus component (S) is extracted from the second-order Zernike coefficients, providing a direct, quantitative measure of the refractive error in diopters. This value serves as a precise error signal in a closed-loop control system, which commands a voice-coil actuated focusing lens to its null position in a single, deterministic step, eliminating the need for iterative search algorithms. ResultsComprehensive evaluation demonstrated the system’s high performance. Testing on a calibrated model eye (OEMI-7) established a highly linear relationship between the computed defocus S and the focusing lens position across a ±20 Diopter (D) compensation range, achievable within a 5 mm mechanical travel. The system achieved a focusing precision of 0.08 D, corresponding to an 18-fold improvement over a conventional projection spot-size method tested under identical conditions. The total focus acquisition time, encompassing wavefront measurement, computation, and lens actuation, averaged under 0.5 s. Clinical validation with 25 human volunteers (50 eyes, refractive range -15 D to +10 D) confirmed practical efficacy. The wavefront-sensing AF succeeded in 92% of attempts with a mean time of 0.5 s, substantially outperforming a projection-based benchmark which achieved only a 32% success rate with an average time of 4.25 s. The system provided instantaneous directional guidance and maintained stability during minor ocular movements. Objective assessment of image quality, via amplitude contrast of retinal vasculature, showed consistent and significant enhancement following AF correction across the entire tested diopter range. ConclusionThis work successfully implements and validates a direct wavefront-sensing autofocus paradigm for portable fundus cameras. By directly quantifying and compensating for the optical defocus aberration, this method bypasses the fundamental limitations of image-processing and projection-based techniques, enabling rapid, precise, and deterministic diopter compensation. The developed system delivers an exceptional combination of a wide operational range (±20 D), high accuracy (0.08 D), fast convergence (0.5 s), and a compact physical footprint. This technology provides a practical and high-performance focusing solution capable of enhancing the reliability, throughput, and diagnostic utility of portable retinal imaging in large-scale screening applications. Future efforts will be directed towards system cost optimization and performance adaptation for diverse ocular conditions.

Blood standardization is a crucial means of promoting the healthy and sustainable development of China's blood industry. The construction of a blood standard system serves as the foundational work for blood standardization. To facilitate the continuous improvement of blood standardization efforts, this paper begins by describing the current status and analyzing the issues within China's blood standard system. Through systematic research, it proposes a framework for constructing a blood standard system and offers revision recommendations for its enhancement. Based on the first five editions of the blood standard system developed by Sub-Committee of Blood Standards of National Committee of Health Standards, this study further refines the revision and detailed construction of the standards framework—the primary task in establishing the blood standard system. It provides specific guidance for both the construction and application of the blood standard system. This work serves as a reference and basis for the reasonable and standardized formulation and revision of blood standards, as well as for the management and implementation of blood standardization efforts.

Introduction: Severe hypertriglyceridemia during pregnancy is a rare yet potentially life-threatening disorder. It is frequently linked to acute pancreatitis and poses considerable risks for both maternal and fetal morbidity. Case: We report a 35-year-old G4P3 female at 33 + 6 weeks gestation with underlying type 2 diabetes mellitus who presented with acute abdominal pain, nausea, vomiting, and poor oral intake, initially mistaken for preterm labor and sepsis. Further evaluation revealed profound hypertriglyceridemia (triglycerides 79.1 mmol/L) with markedly elevated total cholesterol (>32 mmol/L) and raised serum amylase, consistent with hypertriglyceridemia-induced acute pancreatitis. She was managed in a multidisciplinary setting with intravenous insulin infusion, dextrose supplementation, aggressive fluid resuscitation, and empiric antibiotics. Due to clinical deterioration and ongoing risk of maternal complications, she underwent emergency lower segment caesarean section and exploratory laparotomy at 34 weeks of gestation. Intraoperative findings included inflammatory intra-abdominal fluid and a bulky pancreas, supporting the diagnosis. Rapid biochemical improvement was observed following treatment, with triglyceride levels decreasing by approximately 70% within 24 hours (79.1– 24.0 mmol/L) and achieving >90% reduction over 10 days. Postpartum management included initiation of omega-3 fatty acids, fibrate, and statin therapy, resulting in sustained lipid control. Ophthalmologic examination demonstrated lipemia retinalis, further confirming severe dyslipidemia. Conclusion This case highlights the importance of early recognition of severe hypertriglyceridemia in pregnancy, particularly in patients with metabolic risk factors such as diabetes. Prompt initiation of insulin therapy can achieve rapid triglyceride reduction and may obviate the need for plasmapheresis in selected cases. Delivery should be considered in the setting of maternal instability. Long-term lipid management postpartum is essential for preventing recurrence and reducing future metabolic risk. A multidisciplinary approach remains critical in optimizing both maternal and fetal outcomes in this rare but serious condition.
Female ; Pregnancy ; Acute Disease ; Pancreatitis

Objective: To investigate the intervention effects and mechanisms of function-rehabilitation-oriented physical training on the physical health of higher vocational college students, so as to provide replicable strategies for integrating physical education with health education in such institutions. Methods: In March 2024, a cluster random sampling method was employed to select 312 first and second year non sports major students from Chongqing Water Resources and Electric Engineering College as research subjects, and the selected classes were randomly divided into an intervention group ( n =151) and a control group ( n =161) by using a random number table. Both groups received a 16 week intervention program consisting of 2 academic hours per week from Macrh to July 2024. The control group followed the standard teaching curriculum for public physical education courses in higher vocational education, while the intervention group incorporated a function-rehabilitation-oriented physical training module into the regular physical education curriculum. For the module, stratified functional correction was implemented based on pre class functional movement screening results, with dedicated 10-15 minute intervention sessions per lesson accompanied by personalized exercise prescriptions delivered three times weekly. Before and after the intervention, Functional Movement Screen, the Exercise Attitude Scale, and the National Student Physical Health Standards (2014 Revision) were used for pre and post intervention assessments. Main effect of the intervention was examined via repeated measures analysis of variance, while chain mediating effect was analyzed by using the Hayes Process macro program. Results: After the intervention, the scores for functional movement quality (15.82±2.35), physical exercise attitude (237.64±17.22), and physical health level (76.45±7.82) in the intervention group were significantly higher than those before intervention (13.10±2.41, 199.51±15.78, 70.30±8.34) and those in the control group during the same period (13.08±2.81, 199.02±18.67, 71.42±7.56)( t =10.07, 20.34, 6.58; 9.21, 19.17, 5.57, all P < 0.01 ). Function-rehabilitation-oriented physical training directly and positively predicted physical health status ( β =0.18). Functional movement quality (effect size=0.21) and physical exercise attitude (effect size= 0.15 ) each served as independent mediators, their chain mediating effect was statistically significant (effect size=0.10)(all P < 0.01 ), with the total indirect effect accounting for 71.88% of the overall effect. Conclusion Function-rehabilitation-oriented physical training significantly improves the physical health of vocational college students through both direct effects and chain pathways, making it suitable for widespread implementation in vocational education institutions.

Objective We reviewed and analyzed the epidemiological data of 83 imported dengue fever cases reported in Fengtai District, Beijing, from 2007 to 2025, to delineate their epidemiological characteristics and guide the dengue fever prevention and control strategy in the future. Methods Data on dengue fever cases in Fengtai District from 2007 to 2025 were collected to identify the epidemic factors and characteristics using descriptive epidemiological method. Results All 83 dengue fever cases reported in this region over the past two decades have been imported from abroad or other domestic areas, with Southeast Asian countries being identified as the primary source of imported infections, accounting for 42 cases (50.60%), followed by 15 cases (18.07%) from Chinese provinces other than Beijing. The remaining import sources included 13 cases from South Asia,8 from African countries, and each from Oceania, South America, and Europe. Disease onset was found concentrated between May and November. The sex ratio (male-to-female) is 1.59:1. The age of onset ranged from 14 to 61 years old, with a median age of 36. The largest proportion of cases was observed among cadres and office workers (31 cases, 37.35%), followed by businessmen (13 cases, 15.67%), and householders or the unemployed (10 cases,12.05%). Travel visit was identified as the primary reason for their exposure history. Conclusions All dengue fever cases reported in Fengtai from 2007 to 2025 were imported, with an increasing trend of imported cases in Beijing originating from other Chinese provinces. It is essential to strengthen health education for foreign travelers and returning residents, enhance clinical diagnosis and treatment training for medical personnel, eliminate mosquito breeding sites, and reduce mosquito density through active patriotic health campaigns.

ObjectiveThe controllability changes of structural brain network were explored based on the control and brain network theory in young smokers, this may reveal that the controllability indicators can serve as a powerful factor to predict the sleep status in young smokers. MethodsFifty young smokers and 51 healthy controls from Inner Mongolia University of Science and Technology were enrolled. Diffusion tensor imaging (DTI) was used to construct structural brain network based on fractional anisotropy (FA) weight matrix. According to the control and brain network theory, the average controllability and the modal controllability were calculated. Two-sample t-test was used to compare the differences between the groups and Pearson correlation analysis to examine the correlation between significant average controllability and modal controllability with Fagerström Test of Nicotine Dependence (FTND) in young smokers. The nodes with the controllability score in the top 10% were selected as the super-controllers. Finally, we used BP neural network to predict the Pittsburgh Sleep Quality Index (PSQI) in young smokers. ResultsThe average controllability of dorsolateral superior frontal gyrus, supplementary motor area, lenticular nucleus putamen, and lenticular nucleus pallidum, and the modal controllability of orbital inferior frontal gyrus, supplementary motor area, gyrus rectus, and posterior cingulate gyrus in the young smokers’ group, were all significantly different from those of the healthy controls group (P<0.05). The average controllability of the right supplementary motor area (SMA.R) in the young smokers group was positively correlated with FTND (r=0.393 0, P=0.004 8), while modal controllability was negatively correlated with FTND (r=-0.330 1, P=0.019 2). ConclusionThe controllability of structural brain network in young smokers is abnormal. which may serve as an indicator to predict sleep condition. It may provide the imaging evidence for evaluating the cognitive function impairment in young smokers.

BACKGROUND:Black phosphorus has a high degree of homology with human bone,so it has been extensively studied in the field of bone tissue engineering in recent years.Since 2014,two-dimensional black phosphorus materials have garned significant attention in the field of biomedicine due to their excellent exceptional physical,chemical,and biological properties. OBJECTIVE:To summarize the advancements made in black phosphorus-based nanomaterials for bone tissue engineering,focus on the synthesis methods,osteogenic characteristics,and applications in biomaterials pertaining to two-dimensional black phosphorus nanomaterials. METHODS:Chinese and English key words were"black phosphorus,bone tissue engineering,bone defect,bone regeneration,osteogenesis."Relevant articles in PubMed and CNKI databases from January 2014 to December 2023 were searched.After exclusion and screening,96 articles were analyzed. RESULTS AND CONCLUSION:Black phosphorus nanomaterials play an important role in bone tissue engineering due to their good biocompatibility,biodegradability,photothermal action,antibacterial ability,drug loading performance,and special osteogenic effect,and are ideal candidate materials for promoting bone regeneration.The preparation of black phosphorus nanomaterials is mainly a top-down top-layer stripping method.The main principle is to weaken the van der Waals force between the black phosphorus layers by physical or chemical means to obtain a single or less layer of phosphanse,that is,black phosphorus nanosheets or quantum dots.Black phosphate-based nanocomposites are mainly divided into hydrogels,3D printing scaffolds,composite scaffolds,electrospinning,bionic periosteum,microspheres,and bionic coatings.The research of nano-black phosphorus in bone tissue engineering is in its infancy,and still faces many challenges:the behavior of black phosphorus in vivo and the interaction mechanism with various biomolecules need to be further studied.The long-term potential toxicity of black phosphorus is unknown.The manufacturing process for black phosphorus is difficult to control.Therefore,how to develop uniform size,safe,reliable,and efficient nano black phosphorus and transform it into clinical application requires interdisciplinary research on modern biomedical technology,physicochemical technology,and precision manufacturing technology.

The general models for intermediates quality analysis in the production process of Yaobitong capsule were established by near infrared spectroscopy (NIRS) combined with chemometrics, realizing the rapid determination of notoginsenoside R1, ginsenoside Rg1, ginsenoside Re, ginsenoside Rb1, ginsenoside Rd and moisture. The spray-dried fine powder and total mixed granule were selected as research objects. The contents of five saponins were determined by high performance liquid chromatography and the moisture content was determined by drying method. The measured contents were used as reference values. Meanwhile, NIR spectra were collected. After removing abnormal samples by Monte Carlo cross validation (MCCV), Monte Carlo uninformative variables elimination (MC-UVE) and competitive adaptive reweighted sampling (CARS) were used to select feature variables respectively. Based on the feature variables, quantitative models were established by partial least squares regression (PLSR), extreme learning machine (ELM) and ant lion optimization least squares support vector machine (ALO-LSSVM). The results showed that CARS-ALO-LSSVM model had the optimum effect. The correlation coefficients of the six index components were greater than 0.93, and the relative standard errors were controlled within 6%. ALO-LSSVM was more suitable for a large number of samples with rich information, and the prediction effect and stability of the model were significantly improved. The general models with good predicting effect can be used for the rapid quality determination of Yaobitong capsule intermediates.

Objective To investigate the visit duration of patients attending traditional Chinese medicine(TCM)tumor rehabilitation outpatient clinic in a tertiary hospital,analyze its influencing factors and explore the corresponding improvement strategies.Methods A total of 317 patients in the TCM Tumor Rehabilitation Clinic of Sichuan Cancer Hospital from February to April 2023 were selected as study subjects.Patient characteristics and symptom burden were analyzed by using generalized linear regression model.Results Restless sleep were the most severe symptoms,followed by fatigue,forgetfulness,dry mouth,and loss of appetite.Fear of cold is the most serious TCM-specific symptom.Age,number of patient peers,and poor performance status or severe fatigue were the main factors influencing the duration of patients'visits.Conclusion TCM cancer rehabilitation outpatient patients have taken a long time and have a heavy symptom burden,the main influencing factors are age,number of patients,poor physical condition or severe fatigue.

Objective To explore the characteristics,potential challenges,and optimization paths of high-quality development policies for public hospitals in China,and to provide reference for policy formulation and implementation.Methods The 31 policy documents on high-quality development of public hospitals issued at the central and provincial levels between 2021 and 2024 were coded using Nvivo 11 software,and a three-dimensional analytical framework was constructed on the basis of the policy tools,stakeholders,and system dimensions,combining both quantitative and qualitative methods for content analysis.Results It found that the distribution of policy content in the three dimensions was characterized by stage imbalance:policy tools were mainly environmental,followed by supply,and demand;stakeholder attention was focused on public hospitals and healthcare administrations,and patient attention was low;The system dimension focused mainly on the macro level,with less distribution at the meso and micro levels.Although the unbalanced distribution of policy instruments is relevant at certain stages,the long-term structural imbalance may lead to insufficient systemic policies and weakened stakeholder synergies,and there is an urgent need to optimize the structure of instruments.Conclusions It is recommended to increase the proportion of demand-based policy instruments in policy design and dynamically adjust the synergistic application of the three types of instruments;to strengthen the attention to vulnerable stakeholders,such as patients;and to optimize the design of policies at the meso-levels and micro-levels in order to enhance the systemicity and sustainability of policy implementation.