OBJECTIVE: To evaluate the effects of posterior cruciate ligament(PCL) resection on soft tissue elasticity and knee stability in total knee arthroplasty(TKA). METHODS: Six adult cadaveric knee specimens (involving 10 knees) were included in the study. With the assistance of the robotic system(TiRobot Recon, TINAVI, Beijing), total knee arthroplasty (TKA) was performed sequentially using cruciate retaining (CR) prostheses and posterior stabilizing (PS) prostheses. Between the two surgical procedures, the femoral and tibial osteotomy surfaces were not altered;only the posterior cruciate ligament (PCL) was resected and the intercondylar fossa was treated. After installing the femoral trial component, a soft tissue balance solver was used to apply tension ranging from 30 N to 90 N in 5 N increments at 0°, 10°, and 90° of knee flexion. Meanwhile, the medial and lateral joint gaps were measured synchronously. Based on the tension-gap coupling data, the equivalent elastic coefficients of the medial and lateral soft tissue sleeves at different knee flexion angles, as well as the range of the joint line convergence angle (JLCA) under fixed varus-valgus stress, were calculated. Additionally, the gap balance status under 80 N of tension was analyzed. Self-control comparisons of each indicator were conducted before and after PCL resection to analyze the change patterns. RESULTS: After PCL resection, in the fully extended position (knee flexion 0°). The medial equivalent elastic coefficient was 32.2 (25.7, 63.3) N·mm^-1 for the CR prosthesis and 27.7 (22.0, 51.9) N·mm^-1 for the PS prosthesis, and the statistically significant difference (P=0.013). The range of JLCA was 0.41°(0.26, 0.55)° for the CR prosthesis, which was smaller than 0.75° (0.40, 0.98)° for the PS prosthesis, and the difference was statistically significant(P=0.041). At 90° of knee flexion, the medial joint gap was 10.7(10.1, 11.7) mm for the CR prosthesis, which was smaller than 12.1(10.9, 15.1) mm for the PS prosthesis, with a statistically significant difference(P=0.011). No statistically significant differences were observed in other joint gaps. CONCLUSION PCL resection reduces the rigidity of the medial soft tissues in the fully extended knee and increases the medial joint gap in the flexed position, thereby affecting knee stability and balance. This finding suggests that PS and CR prostheses may require different morphological designs, and there should be differences in indications and osteotomy strategies between CR-TKA and PS-TKA. CR-TKA is more suitable for patients with preoperative medial soft tissue laxity.
Humans ; Posterior Cruciate Ligament/physiopathology* ; Knee Joint/physiopathology* ; Arthroplasty, Replacement, Knee ; Elasticity ; Male ; Female ; Middle Aged ; Aged ; Biomechanical Phenomena ; Adult

OBJECTIVE: To evaluate the dynamic changes of glucocorticoid (GC) dose and the feasibility of GC discontinuation in rheumatoid arthritis (RA) patients under the background of Chinese medicine (CM). METHODS: This multicenter retrospective cohort study included 1,196 RA patients enrolled in the China Rheumatoid Arthritis Registry of Patients with Chinese Medicine (CERTAIN) from September 1, 2019 to December 4, 2023, who initiated GC therapy. Participants were divided into the Western medicine (WM) and integrative medicine (IM, combination of CM and WM) groups based on medication regimen. Follow-up was performed at least every 3 months to assess dynamic changes in GC dose. Changes in GC dose were analyzed by generalized estimator equation, the probability of GC discontinuation was assessed using Kaplan-Meier curve, and predictors of GC discontinuation were analyzed by Cox regression. Patients with <12 months of follow-up were excluded for the sensitivity analysis. RESULTS: Among 1,196 patients (85.4% female; median age 56.4 years), 880 (73.6%) received IM. Over a median 12-month follow-up, 34.3% (410 cases) discontinued GC, with significantly higher rates in the IM group (40.8% vs. 16.1% in WM; P<0.05). GC dose declined progressively, with IM patients demonstrating faster reductions (median 3.75 mg vs. 5.00 mg in WM at 12 months; P<0.05). Multivariate Cox analysis identified age <60 years [P<0.001, hazard ratios (HR)=2.142, 95% confidence interval (CI): 1.523-3.012], IM therapy (P=0.001, HR=2.175, 95% CI: 1.369-3.456), baseline GC dose ⩽7.5 mg (P=0.003, HR=1.637, 95% CI: 1.177-2.275), and absence of non-steroidal anti-inflammatory drugs use (P=0.001, HR=2.546, 95% CI: 1.432-4.527) as significant predictors of GC discontinuation. Sensitivity analysis (545 cases) confirmed these findings. CONCLUSIONS RA patients receiving CM face difficulties in following guideline-recommended GC discontinuation protocols. IM can promote GC discontinuation and is a promising strategy to reduce GC dependency in RA management. (Trial registration: ClinicalTrials.gov, No. NCT05219214).
Adult ; Aged ; Female ; Humans ; Male ; Middle Aged ; Arthritis, Rheumatoid/drug therapy* ; Glucocorticoids/therapeutic use* ; Medicine, Chinese Traditional ; Retrospective Studies

OBJECTIVE: This study examines the sequential mediating roles of body pain and self-reported health in the association between sleep duration and self-reported life satisfaction among elderly Chinese adults. METHODS: Data from the fifth wave of the China Health and Retirement Longitudinal Survey (CHARLS) were used to analyse the relationships between sleep duration and body pain, self-reported health, and life satisfaction through logistic regression and Restricted Cubic Spline (RCS) analyses. The sequential mediation effects of body pain and self-reported health status were examined via chain mediation analysis. RESULTS: Logistic regression analysis showed that sleeping fewer than 6 hours or 6-7 hours was linked to higher risks of body pain, poor health, and dissatisfaction with life compared to sleeping 7-8 hours (all P < 0.05). Additionally, those sleeping more than 9 hours also had increased risks of poor health and dissatisfaction with life compared to those sleeping 7-8 hours (all P < 0.05). Chain mediation analysis showed that body pain and self-reported health status sequentially mediated 46.15% of the association between sleep duration and life satisfaction. CONCLUSION Body pain and self-reported health may shape the relationship between sleep duration and life satisfaction in elderly Chinese adults.
Humans ; Male ; Female ; Aged ; Personal Satisfaction ; Sleep ; Health Status ; Self Report ; China ; Middle Aged ; Longitudinal Studies ; Pain/psychology* ; Sleep Duration

Objective To evaluate the efficacy and safety of brexpiprazole in treating acute schizophrenia.Methods Patients with schizophrenia were randomly divided into treatment group and control group.The treatment group was given brexpiprozole 2-4 mg·d-1 orally and the control group was given aripiprazole 10-20 mg·d-1orally,both were treated for 6 weeks.Clinical efficacy of the two groups,the response rate at endpoint,the changes from baseline to endpoint of Positive and Negative Syndrome Scale(PANSS),Clinical Global Impression-Improvement(CGI-S),Personal and Social Performance scale(PSP),PANSS Positive syndrome subscale,PANSS negative syndrome subscale were compared.The incidence of treatment-related adverse events in two groups were compared.Results There were 184 patients in treatment group and 186 patients in control group.After treatment,the response rates of treatment group and control group were 79.50％(140 cases/184 cases)and 82.40％(150 cases/186 cases),the scores of CGI-I of treatment group and control group were(2.00±1.20)and(1.90±1.01),with no significant difference(all P＞0.05).From baseline to Week 6,the mean change of PANSS total score wese(-30.70±16.96)points in treatment group and(-32.20±17.00)points in control group,with no significant difference(P＞0.05).The changes of CGI-S scores in treatment group and control group were(-2.00±1.27)and(-1.90±1.22)points,PSP scores were(18.80±14.77)and(19.20±14.55)points,PANSS positive syndrome scores were(-10.30±5.93)and(-10.80±5.81)points,PANSS negative syndrome scores were(-6.80±5.98)and(-7.30±5.15)points,with no significant difference(P＞0.05).There was no significant difference in the incidence of treatment-related adverse events between the two group(69.00％vs.64.50％,P＞0.05).Conclusion The non-inferiority of Brexpiprazole to aripiprazole was established,with comparable efficacy and acceptability.

Objective To investigate the effects of forsythinol(Fo)on the expression of matrix metalloproteinase-2(MMP2)in hepatoma cells through Janus kinase 2/signal transduction and transcriptional activator 3(JAK2/STAT3)signaling pathway.Methods SMMC-7721 cells were divided into experimental-L,-M,-H groups,control group,inhibitor group and activator group.The control group was added with equal volume dimethyl sulfoxide(DMSO);the experimental-L,-M,-H groups were treated with 50,200,500 μg·mL-1 Fo;and the inhibitor group was added with 50 μmol·L-1 JAK2/STAT3 inhibitor AG490 based on the experimental-M group.In the activator group,10 μmol·L-1 JAK2/STAT3 activator Broussonin E was added to the experimental-M group.Apoptosis was detected by deoxynucleotide terminal transferase-mediated dUTP notch end labeling(TUNEL);protein expression was detected by Western blot;real-time quantitative polymerase chain reaction(qRT-PCR)was used to detect mRNA levels.Results The apoptosis rates of control group,experimental-M group,inhibitor group and activator group were(19.94±4.88)％,(27.04±5.27)％,(15.36±3.40)％and(46.66±7.89)％,respectively;the relative expression levels of phosphorylated JAK2 protein were 1.00±0.13,0.73±0.11,1.33±0.17 and 0.26±0.07,respectively;the relative expression levels of phosphorylated STAT3 protein were 1.00±0.12,0.27±0.04,0.88±0.13 and 0.12±0.04,respectively;the mRNA relative expression levels of MMP2 were 1.00±0.14,0.68±0.08,1.17±0.17 and 0.51±0.09,respectively.Compared with experimental-M group and control group,inhibitor group and activator group,there were statistically significant differences(P＜0.05,P＜0.001).Conclusion Fo promotes apoptosis of hepatocellular carcinoma cells,and its mechanism may be related to the effect of Fo on the expression of MMP2 by regulating JAK2-STAT3 signaling pathway.

Objective:To analyze the influence of forming direction on the surface characteristics,elastic modulus,bending strength and fracture toughness of printed parts and the relationship between forming direction and force direction,and to provide scientific basis and guidance for the clinical applica-tion of oral denture base resin materials.Methods:The 3D printing technology was used to print denture base resin samples.The shape and size of the samples referred to the current standard for testing conven-tional denture base materials.The samples used for physical performance testing were cylindrical(with a diameter of 15 mm and a thickness of 1 mm)and printed at different angles along the Z axis(0°,45°,90°).Scanning electron microscope was used to observe the microscopic topography of the different sam-ples.The color stability of different samples was observed by color stabilizer.The surface roughness of the samples was analyzed by using surface roughness tester.The Vickers hardness was measured to ana-lyze the hardness of the samples.The samples used for mechanical performance testing were rectangular(elastic modulus and bending strength:A length of 64 mm,a width of 10 mm,and a height of 3.3 mm;fracture toughness:A length of 39 mm,a width of 8 mm,and a height of 4 mm),divided into two groups:W group and H group.The W group was printed from the bottom up along the Z axis with the length × width as the bottom surface parallel to the X,Y axis plane,while the H group printed from the bottom up along the Z axis with the length × height as the bottom surface parallel to the X,Y axis plane.The forming angles of both groups were equally divided into 0°,45°,and 90°.The elastic modulus,bending strength and fracture toughness of different samples were studied through universal mechanical testing machine.SPSS 22.0 software was used for statistical analysis.Results:The microscopic topogra-phy and roughness of different samples were closely related to the printing direction,with significant differences between the 0°,45°,and 90° specimens.The 0° specimens had the smoothest surface(roughness＜1 μm).The surface of the 45 ° specimen was the roughest(roughness＞3 μm).The microhardness of the 0° sample was the best[(196.13±0.20)MPa],with a significant difference com-pared with the 90° sample[(186.62±4.81)MPa,P＜0.05].The mechanical properties of different samples were also closely related to the printing direction.The elastic modulus,bending strength,and fracture toughness of the 45° samples in the W group were the highest compared with the other groups.The results of elastic modulus showed that in the H group,the 45° specimens had the highest elastic mo-dulus,which was significantly different from the 0° and 90° specimens(P＜0.05).The elastic modulus of 0° and 45° specimens in the W group were higher than those in 90° specimens(P＜0.05).The bending strength results showed that there was no significant difference between the specimens from dif-ferent angles in the H group.The bending strength of the 90° specimens in the W group was the smallest,and there was a significant difference between 90° and the 0° and 45° specimens(P＜0.05);And the bendind strength of the 0° and 45° specimens in the W group was significantly higher than that of the 0° and 45° specimens in the H group(P＜0.05).The fracture toughness results showed that the fracture toughness of the H group specimens was lower than 1.9 MPa m1/2,which was specified in the denture base standard.The 45° samples in the W group were the highest,with significant differences compared with the 0° and 90° samples(P＜0.05).And the 90° samples of the W group specimens were lower than 1.9 MPa m1/2.And the fracture toughness of the 45° specimen in the W group was significantly higher than that of all the specimens in the H group(P＜0.05).Conclusion:The 0° samples had rela-tively better physical properties.The 45° samples had the best mechanical properties.But the fracture toughness of specimens(H group and 90° samples of W group)did not yet meet clinical requirements.That indicated that the characteristics of the 3D printing denture base resin were affected by the printing direction.Only when the performance of the printed samples in all directions met the minimum require-ments of the standard,they could be used in clinical practice.

Objective To summarize the epidemiological and clinical features of infectious diseases of the central nervous system(CNS)by a single-center analysis.Methods A retrospective analysis was conducted on the data of 1247 cases of CNS infectious diseases diagnosed and treated in the First Medical Center of PLA General Hospital from 2001 to 2020.Results The data for this group of CNS infectious diseases by disease type in descending order of number of cases were viruses 743(59.6％),Mycobacterium tuberculosis 249(20.0％),other bacteria 150(12.0％),fungi 68(5.5％),parasites 18(1.4％),Treponema pallidum 18(1.4％)and rickettsia 1(0.1％).The number of cases increased by 177 cases(33.1％)in the latter 10 years compared to the previous 10 years(P<0.05).No significant difference in seasonal distribution pattern of data between disease types(P>0.05).Male to female ratio is 1.87︰1,mostly under 60 years of age.Viruses are more likely to infect students,most often at university/college level and above,farmers are overrepresented among bacteria and Mycobacterium tuberculosis,and more infections of Treponema pallidum in workers.CNS infectious diseases are characterized by fever,headache and signs of meningeal irritation,with the adductor nerve being the more commonly involved cranial nerve.Matagenomic next-generation sequencing improves clinical diagnostic capabilities.The median hospital days for CNS infectious diseases are 18.00(11.00,27.00)and median hospital costs are ￥29,500(￥16,000,￥59,200).The mortality rate from CNS infectious diseases is 1.6％.Conclusions The incidence of CNS infectious diseases is increasing last ten years,with complex clinical presentation,severe symptoms and poor prognosis.Early and accurate diagnosis and standardized clinical treatment can significantly reduce the morbidity and mortality rate and ease the burden of disease.

Objective This study aimed to investigate the potential relationship between urinary metals copper (Cu), arsenic (As), strontium (Sr), barium (Ba), iron (Fe), lead (Pb) and manganese (Mn) and grip strength. Methods We used linear regression models, quantile g-computation and Bayesian kernel machine regression (BKMR) to assess the relationship between metals and grip strength.Results In the multimetal linear regression, Cu (β=-2.119), As (β=-1.318), Sr (β=-2.480), Ba (β=0.781), Fe (β= 1.130) and Mn (β=-0.404) were significantly correlated with grip strength (P < 0.05). The results of the quantile g-computation showed that the risk of occurrence of grip strength reduction was -1.007 (95％ confidence interval:-1.362, -0.652; P < 0.001) when each quartile of the mixture of the seven metals was increased. Bayesian kernel function regression model analysis showed that mixtures of the seven metals had a negative overall effect on grip strength, with Cu, As and Sr being negatively associated with grip strength levels. In the total population, potential interactions were observed between As and Mn and between Cu and Mn (Pinteractions of 0.003 and 0.018, respectively).Conclusion In summary, this study suggests that combined exposure to metal mixtures is negatively associated with grip strength. Cu, Sr and As were negatively correlated with grip strength levels, and there were potential interactions between As and Mn and between Cu and Mn.

Purpose::This study evaluated the methods and clinical effects of multidisciplinary collaborative treatment for occlusal reconstruction in patients with old jaw fractures and dentition defects.Methods::Patients with old jaw fractures and dentition defects who underwent occlusal reconstruction at the Third Affiliated Hospital of Air Force Military Medical University from January 2018 to December 2022 were enrolled. Clinical treatment was classified into 3 phases. In phase I, techniques such as orthognathic surgery, microsurgery, and distraction osteogenesis were employed to reconstruct the correct 3-dimensional (3D) jaw position relationship. In phase II, bone augmentation and soft tissue management techniques were utilized to address insufficient alveolar bone mass and poor gingival soft tissue conditions. In phase III, implant-supported overdentures or fixed dentures were used for occlusal reconstruction. A summary of treatment methods, clinical efficacy evaluation, comparative analysis of imageological examinations, and satisfaction questionnaire survey were utilized to evaluate the therapeutic efficacy in patients with traumatic old jaw fractures and dentition defects. All data are summarized using the arithmetic mean ± standard deviation and compared using independent sample t-tests. Results::In 15 patients with old jaw fractures and dentition defects (an average age of 32 years, ranging from 18 to 53 years), there were 7 cases of malocclusion of single maxillary fracture, 6 of malocclusion of single mandible fracture, and 2 of malocclusion of both maxillary and mandible fractures. There were 5 patients with single maxillary dentition defects, 2 with single mandibular dentition defects, and 8 with both maxillary and mandibular dentition defects. To reconstruct the correct 3D jaw positional relationship, 5 patients underwent Le Fort I osteotomy of the maxilla, 3 underwent bilateral sagittal split ramus osteotomy of the mandible, 4 underwent open reduction and internal fixation for old jaw fractures, 3 underwent temporomandibular joint surgery, and 4 underwent distraction osteogenesis. All patients underwent jawbone augmentation, of whom 4 patients underwent a free composite vascularized bone flap (26.66%) and the remaining patients underwent local alveolar bone augmentation. Free gingival graft and connective tissue graft were the main methods for soft tissue augmentation (73.33%). The 15 patients received 81 implants, of whom 11 patients received implant-supported fixed dentures and 4 received implant-supported removable dentures. The survival rate of all implants was 93.82%. The final imageological examination of 15 patients confirmed that the malocclusion was corrected, and the clinical treatment ultimately achieved occlusal function reconstruction. The patient satisfaction questionnaire survey showed that they were satisfied with the efficacy, phonetics, aesthetics, and comfort after treatment.Conclusion::Occlusal reconstruction of old jaw fractures and dentition defects requires a phased sequential comprehensive treatment, consisting of 3D spatial jaw correction, alveolar bone augmentation and soft tissue augmentation, and implant-supported occlusal reconstruction, achieving satisfactory clinical therapeutic efficacy.

Objective To explore the selection rules of acupuncture and moxibustion for treating ovarian dysfunction-related diseases by applying data mining technology.Methods Computer searches were conducted to find clinical research literature on acupuncture and moxibustion for ovarian reserve dysfunction-related diseases(including diminished ovarian reserve,premature ovarian insufficiency,premature ovarian failure)in major databases,such as China National Knowledge Infrustructure(CNKI),Wanfang Data Knowledge Service Platform(Wanfang),and China Science and Technology Journal Database(VIP),Excel 2021 was used to establish a prescription database of acupoints selection,and SPSS Modeler 18.0 and SPSS Stastics 26.0 software were used to analyse the frequency,meridian tropism,site,special acupoints,analysis of association rule,and cluster analysis of acupoints to study the rules of acupuncture and moxibustion for treating ovarian reserve dysfunction-related diseases.Results A total of 215 articles were screened to meet the requirements,in which,96 acupoints were used,with a total frequency of 2 110 times.The high-frequency used acupoints were Guanyuan(RN4),Sanyinjiao(SP6),and Shenshu(BL23),etc,.The commonly used meridians were the conception vessel(CV)and bladder meridian of foot-taiyang,and the acupoints were mostly located in the abdomen and lower limbs,with the majority being the five-shu point and the yuan front-mu points.The core acupoints and four effective clusters were analysed.Conclusion The acupoint selection of acupuncture and moxibustion for ovarian reserve dysfunction-related diseases focuses on tonifying qi and blood,cultivating the vital essence and tonifying the kidneys.Most of the meridians related to reproduction were selected in this method,which aiming at regulating menstruation and tonifying blood,and pre-cultivating its loss.This research focuses on the matching of neighboring point and distant point selection,and pays attention to the use of specific acupoints,and treates multiple organs simultaneously.