Prosthesis loosening is the leading cause of postoperative revision in unicompartmental knee arthroplasty (UKA). The deviation of medial and lateral translational installation of the prosthesis during surgery is a common clinical phenomenon and an important factor in increasing the risk of prosthesis loosening. This study established a UKA finite element model and a bone-prosthesis fixation interface micromotion prediction model. The predicted medial contact force and joint motion of the knee joint from a patient-specific lower extremity musculoskeletal multibody dynamics model of UKA were used as boundary conditions. The effects of 9 femoral component medial and lateral translational installation deviations on the Von Mises stress of the proximal tibia, the contact stress, and the micro-motion of the bone prosthesis fixation interface were quantitatively studied. It was found that compared with the neutral position (a/A of 0.492), the lateral translational deviation of the femoral component significantly increased the tibial Von Mises stress and the bone-prosthesis fixation interface contact stress. The maximum Von Mises stress and the maximum contact stress of the fixation interface increased by 14.08% and 143.15%, respectively, when a/A was 0.361. The medial translational deviation of the femoral component significantly increased the bone-prosthesis fixation interface micro-motion. The maximum value of micromotion under the conditions of femoral neutral and medial translation deviation was in the range of 20-50 μm, which is suitable for osseointegration. Therefore, based on considerations such as the micromotion range suitable for osseointegration reported in the literature, the risk of reducing prosthesis loosening, and factors that may induce pain, it is recommended that clinicians control the mounting position of the femoral component during surgery within the safe range of 0-4 mm medial translation deviation.
Humans ; Arthroplasty, Replacement, Knee/methods* ; Finite Element Analysis ; Biomechanical Phenomena ; Knee Prosthesis ; Tibia/surgery* ; Femur/surgery* ; Stress, Mechanical ; Prosthesis Failure ; Knee Joint/surgery* ; Prosthesis Design

This article aims to compare and analyze the biomechanical differences between wing-shaped titanium plates and traditional titanium plates in fixing acetabular anterior column and posterior hemi-transverse (ACPHT) fracture under multiple working conditions using the finite element method. Firstly, four sets of internal fixation models for acetabular ACPHT fractures were established, and the hip joint stress under standing, sitting, forward extension, and abduction conditions was calculated through analysis software. Then, the stress of screws and titanium plates, as well as the stress and displacement of the fracture end face, were analyzed. Research has found that when using wing-shaped titanium plates to fix acetabular ACPHT fractures, the peak stress of screws decreases under all working conditions, while the peak stress of wing-shaped titanium plates decreases under standing and sitting conditions and increases under forward and outward extension conditions. The relative displacement and mean stress of the fracture end face decrease under all working conditions, but the values are higher under forward and outward extension conditions. Wing-shaped titanium plates can reduce the probability of screw fatigue failure when fixing acetabular ACPHT fractures and can bear greater loads under forward and outward extension conditions, improving the mechanical stability of the pelvis. Moreover, the stress on the fracture end surface is more conducive to stimulating fracture healing and promoting bone tissue growth. However, premature forward and outward extension rehabilitation exercises should not be performed.
Titanium ; Bone Plates ; Humans ; Acetabulum/surgery* ; Fracture Fixation, Internal/methods* ; Biomechanical Phenomena ; Finite Element Analysis ; Bone Screws ; Fractures, Bone/surgery* ; Stress, Mechanical ; Working Conditions

Alveolar bone reconstruction simulation is an effective means for quantifying orthodontics, but currently, it is not possible to directly obtain human alveolar bone material models for simulation. This study introduces a prediction method for the equivalent shear modulus of three-dimensional random porous materials, integrating the first-order Ogden hyperelastic model to construct a computed tomography (CT) based porous hyperelastic Ogden model (CT-PHO) for human alveolar bone. Model parameters are derived by combining results from micro-CT, nanoindentation experiments, and uniaxial compression tests. Compared to previous predictive models, the CT-PHO model shows a lower root mean square error (RMSE) under all bone density conditions. Simulation results using the CT-PHO model parameters in uniaxial compression experiments demonstrate more accurate prediction of the mechanical behavior of alveolar bone under compression. Further prediction and validation with different individual human alveolar bone samples yield accurate results, confirming the generality of the CT-PHO model. The study suggests that the CT-PHO model proposed in this paper can estimate the material properties of human alveolar bone and may eventually be used for bone reconstruction simulations to guide clinical treatment.
Humans ; Tomography, X-Ray Computed/methods* ; Porosity ; Alveolar Process/physiology* ; Bone Density ; Computer Simulation ; Elasticity ; X-Ray Microtomography ; Stress, Mechanical ; Finite Element Analysis ; Models, Biological

In order to investigate the mechanical response of lumbar vertebrae during gait cycle in adolescents with idiopathic scoliosis (AIS), the present study was based on computed tomography (CT) data of AIS patients to construct model of the left support phase (ML) and model of the right support phase (MR), respectively. Firstly, material properties, boundary conditions and load loading were set to simulate the lumbar vertebra-pelvis model. Then, the difference of stress and displacement in the lumbar spine between ML and MR was compared based on the stress and displacement cloud map. The results showed that in ML, the lumbar stress was mostly distributed on the convex side, while in MR, it was mostly distributed on the concave side. The stress of the two types of stress mainly gathered near the vertebral arch plate, and the stress of the vertebral arch plate was transmitted to the vertebral body through the pedicle with the progress of gait. The average stress of the intervertebral tissue in MR was greater than that in ML, and the difference of stress on the convex and convex side was greater. The displacement of lumbar vertebrae in ML decreased gradually from L1 to L5. The opposite is true in MR. In conclusion, this study can accurately quantify the stress on the lumbar spine during gait, and may provide guidance for brace design and clinical decision making.
Humans ; Lumbar Vertebrae/diagnostic imaging* ; Scoliosis/diagnostic imaging* ; Adolescent ; Gait/physiology* ; Biomechanical Phenomena ; Tomography, X-Ray Computed ; Stress, Mechanical ; Female ; Male

Although metal blocks have been widely used for reconstructing uncontained tibial bone defects, the influence of their elastic modulus on the stability of tibial prosthesis fixation remains unclear. Based on this, a finite element model incorporating constrained condylar knee (CCK) prosthesis, tibia, and metal block was established. Considering the influence of the post-restraint structure of the prosthesis, the effects of variations in the elastic modulus of the block on the von Mises stress distribution in the tibia and the block, as well as on the micromotion at the bone-prosthesis fixation interface, were investigated. Results demonstrated that collision between the insert post and femoral prosthesis during tibial internal rotation increased tibial von Mises stress, significantly influencing the prediction of block elastic modulus variation. A decrease in the elastic modulus of the metal block resulted in increased von Mises stress in the proximal tibia, significantly reduced von Mises stress in the distal tibia, decreased von Mises stress of the block, and increased micromotion at the bone-prosthesis fixation interface. When the elastic modulus of the metal block fell below that of bone cement, inadequate block support substantially increased the risk of stress shielding in the distal tibia and fixation interface loosening. Therefore, this study recommends that biomechanical investigations of CCK prostheses must consider the post-constraint effect, and the elastic modulus of metal blocks for bone reconstruction should not be lower than 3 600 MPa.
Knee Prosthesis ; Humans ; Finite Element Analysis ; Tibia/surgery* ; Elastic Modulus ; Arthroplasty, Replacement, Knee/methods* ; Stress, Mechanical ; Metals ; Prosthesis Design ; Knee Joint/surgery* ; Biomechanical Phenomena

The lumbar intervertebral disc exhibits a complex physiological structure with interactions between various segments, and its components are extremely complex. The material properties of different components in the lumbar intervertebral disc, especially the water content (undergoing dynamic change as influenced by age, degeneration, mechanical loading, and proteoglycan content) - critically determine its mechanical properties. When the lumbar intervertebral disc is under continuous pressure, water seeps out, and after the pressure is removed, water re-infiltrates. This dynamic fluid exchange process directly affects the mechanical properties of the lumbar intervertebral disc, while previous isotropic modeling methods have been unable to accurately reflect such solid-liquid phase behaviors. To explore the load-bearing mechanism of the lumbar intervertebral disc and establish a more realistic mechanical model of the lumbar intervertebral disc, this study developed a solid-liquid biphasic, fiber-reinforced finite element model. This model was used to simulate the four movements of the human lumbar spine in daily life, namely flexion, extension, axial rotation, and lateral bending. The fluid pressure, effective solid stress, and liquid pressure-bearing ratio of the annulus fibrosus and nucleus pulposus of different lumbar intervertebral discs were compared and analyzed under the movements. Under all the movements, the fluid pressure distribution was closer to the nucleus pulposus, while the effective solid stress distribution was more concentrated in the outer annulus fibrosus. In terms of fluid pressure, the maximum fluid pressure of the lumbar intervertebral disc during lateral bending was 1.95 MPa, significantly higher than the maximum fluid pressure under other movements. Meanwhile, the maximum effective solid stress of the lumbar intervertebral disc during flexion was 2.43 MPa, markedly higher than the maximum effective solid stress under other movements. Overall, the liquid pressure-bearing ratio under axial rotation was smaller than that under other movements. Based on the solid-liquid biphasic modeling method, this study more accurately revealed the dominant role of the liquid phase in the daily load-bearing process of the lumbar intervertebral disc and the solid-phase mechanical mechanism of the annulus fibrosus load-bearing, and more effectively predicted the solid-liquid phase co-load-bearing mechanism of the lumbar intervertebral disc in daily life.
Humans ; Finite Element Analysis ; Intervertebral Disc/physiology* ; Lumbar Vertebrae/physiology* ; Weight-Bearing/physiology* ; Biomechanical Phenomena ; Stress, Mechanical ; Computer Simulation ; Models, Biological

Stent migration is one of the common complications following transcatheter valve implantation. This study aims to design a "drum-shaped" balloon-expandable aortic valve stent to address this issue and conduct a mechanical analysis. The implantation process of the stent was evaluated using a method that combines numerical simulation and in vitro experiments. Furthermore, the fatigue process of the stent under pulsatile cyclic loading was simulated, and its fatigue performance was assessed using a Goodman diagram. The process of the stent migrating toward the left ventricular side was simulated, and the force-displacement curve of the stent was extracted to evaluate its anti- migration performance. The results showed that all five stent models could be crimped into a 14F sheath and enabled uniform expansion of the native valve leaflets. The stress in each stent was below the ultimate stress, so no fatigue fracture occurred. As the cell height ratio decreased, the contact area fraction between the stent and the aortic root gradually decreased. However, the mean contact force and the maximum anti-migration force first decreased and then increased. Specifically, model S5 had the smallest contact area fraction but the largest mean contact force and maximum anti-migration force, reaching approximately 0.16 MPa and 10.73 N, respectively. The designed stent achieves a "drum-shaped" change after expansion and has good anti-migration performance.
Stents ; Prosthesis Design ; Heart Valve Prosthesis ; Humans ; Aortic Valve/surgery* ; Stress, Mechanical ; Transcatheter Aortic Valve Replacement/instrumentation*

The periodontal ligament (PDL) plays a crucial role in transmitting and dispersing occlusal force, acting as mechanoreceptor for muscle activity during chewing, as well as mediating orthodontic tooth movement. It transforms mechanical stimuli into biological signals, influencing alveolar bone remodeling. Recent research has delved deeper into the biological and mechanical aspects of PDL, emphasizing the importance of understanding its structure and mechanical properties comprehensively. This review focuses on the latest findings concerning both macro- and micro- structural aspects of the PDL, highlighting its mechanical characteristics and factors that influence them. Moreover, it explores the mechanotransduction mechanisms of PDL cells under mechanical forces. Structure-mechanics-mechanotransduction interplay in PDL has been integrated ultimately. By providing an up-to-date overview of our understanding on PDL at various scales, this study lays the foundation for further exploration into PDL-related biomechanics and mechanobiology.
Periodontal Ligament/cytology* ; Humans ; Biomechanical Phenomena ; Mechanotransduction, Cellular/physiology* ; Stress, Mechanical

Mechanical ventilation (MV) is currently widely used in the treatment of respiratory failure and anesthesia surgery, and is a commonly used respiratory support method for critically ill patients; however, improper usage of MV can lead to ventilator-induced lung injury (VILI), which poses a significant threat to patient life. Alveolar epithelial cell (AEC) has the functions of mechanosensation and mechanotransduction. Physiological mechanical stretching is beneficial for maintaining the lineage homeostasis and normal physiological functions of AEC cells, while excessive mechanical stretching can cause damage to AEC cells. Damage to AEC cells is an important aspect in the occurrence and development of VILI. Understanding the effects of mechanical stretching on AEC cells is crucial for developing safe and effective MV strategies, preventing the occurrence of VILI, and improving the clinical prognosis of VILI patients. From the perspective of cell mechanics, this paper aims to briefly elucidate the mechanical properties of AEC cells, mechanosensation and mechanotransduction of mechanical stretching in AEC cells, and the injury and repair of AEC cells under mechanical stretch stimulation, and potential mechanisms with the goal of helping clinical doctors better understand the pathophysiological mechanism of VILI caused by MV, improve their understanding of VILI, provide safer and more effective strategies for the use of clinical MV, and provide theoretical basis for the prevention and treatment of VILI.
Humans ; Mechanotransduction, Cellular ; Ventilator-Induced Lung Injury ; Stress, Mechanical ; Alveolar Epithelial Cells ; Respiration, Artificial/adverse effects* ; Epithelial Cells ; Pulmonary Alveoli/cytology* ; Animals

OBJECTIVES: This study aims to analyze the biomechanics of three kinds of rigid internal fixation methods for condylar head fractures. METHODS: A three dimensional finite element model of the normal mandible was constructed. It was then used to prepare condylar head fracture finite element model and three kinds of rigid internal fixation finite element model (unilateral tension screw, bilateral tension screw, tension screw+titanium plate). The mechanical characteristics and changes of the mandible condyle under the same mechanical conditions were compared among the three different rigid internal fixation methods. RESULTS: The maximum equivalent stress and displacement of the non-free end of condyle under the rigid internal fixation method of unilateral tension screw were 71.03 MPa and 4.72 mm, respectively. The maximum equivalent stress and displacement of the free end of condyle were 78.45 MPa and 4.50 mm, respectively. The maximum stress of fracture suture was 3.27 MPa. The maximum equivalent stress and displacement of the non-free end of condyle under the rigid internal fixation method of bilateral tension screw were 70.52 MPa and 4.00 mm, respectively. The maximum equivalent stress and displacement of the free end of condyle were 72.49 MPa and 3.85 mm, respectively. The maximum stress of fracture suture was 2.33 MPa. The maximum equivalent stress and maximum displacement of the non-free end of condyle under the rigid internal fixation method of tension screw+titanium plate were 67.26 MPa and 2.66 mm, respectively. The maximum equivalent stress and maximum displacement of the free end of condyle were 69.66 MPa and 2.50 mm, respectively. The maximum stress of fracture suture was 2.18 MPa. CONCLUSIONS The tension screw+titanium plate rigid internal fixation method is the most conducive to biomechanical distribution for condylar head fractures.
Fracture Fixation, Internal/instrumentation* ; Mandibular Condyle/surgery* ; Biomechanical Phenomena ; Bone Screws ; Finite Element Analysis ; Humans ; Mandibular Fractures/surgery* ; Bone Plates ; Titanium ; Stress, Mechanical