OBJECTIVES: To determine the optimal timing for post space preparation of root canals sealed with epoxy resin-based AH Plus sealer in terms of its polymerization and influence on apical leakage. MATERIALS AND METHODS: The epoxy polymerization of AH Plus (Dentsply DeTrey) as a function of time after mixing (8, 24, and 72 hours, and 1 week) was evaluated using Fourier transform infrared (FTIR) spectroscopy and microhardness measurements. The change in the glass transition temperature (Tg ) of the material with time was also investigated using differential scanning calorimetry (DSC). Fifty extracted human single-rooted premolars were filled with gutta-percha and AH Plus, and randomly separated into five groups (n = 10) based on post space preparation timing (immediately after root canal obturation and 8, 24, and 72 hours, and 1 week after root canal obturation). The extent of apical leakage (mm) of the five groups was compared using a dye leakage test. Each dataset was statistically analyzed by one-way analysis of variance and Tukey's post hoc test (α = 0.05). RESULTS: Continuous epoxy polymerization of the material with time was observed. Although the T(g) values of the material gradually increased with time, the specimens presented no clear T(g) value at 1 week after mixing. When the post space was prepared 1 week after root canal obturation, the leakage was significantly higher than in the other groups (p < 0.05), among which there was no significant difference in leakage. CONCLUSIONS: Poor apical seal was detected when post space preparation was delayed until 1 week after root canal obturation.
Bicuspid ; Calorimetry, Differential Scanning ; Dataset ; Dental Pulp Cavity* ; Fourier Analysis ; Glass ; Gutta-Percha ; Humans ; Polymerization ; Polymers ; Post and Core Technique ; Root Canal Obturation ; Root Canal Preparation ; Spectrum Analysis ; Transition Temperature

OBJECTIVES: This study evaluated the influence of a multi-mode universal adhesive (MUA) containing silane (Single Bond Universal, 3M EPSE) on the bonding of resin cement to lithium disilicate. MATERIALS AND METHODS: Thirty IPS e.max CAD specimens (Ivoclar Vivadent) were fabricated. The surfaces were treated as follows: Group A, adhesive that did not contain silane (ANS, Porcelain Bonding Resin, Bisco); Group B, silane (S) and ANS; Group C, hydrofluoric acid (HF), S, and ANS; Group D, MUA; Group E, HF and MUA. Dual-cure resin cement (NX3, Kerr) was applied and composite resin cylinders of 0.8 mm in diameter were placed on it before light polymerization. Bonded specimens were stored in water for 24 hours or underwent a 10,000 thermocycling process prior to microshear bond strength testing. The data were analyzed using multivariate analysis of variance (p < 0.05). RESULTS: Bond strength varied significantly among the groups (p < 0.05), except for Groups A and D. Group C showed the highest initial bond strength (27.1 ± 6.9 MPa), followed by Group E, Group B, Group D, and Group A. Thermocycling significantly reduced bond strength in Groups B, C, and E (p < 0.05). Bond strength in Group C was the highest regardless of the storage conditions (p < 0.05). CONCLUSIONS: Surface treatment of lithium disilicate using HF and silane increased the bond strength of resin cement. However, after thermocycling, the silane in MUA did not help achieve durable bond strength between lithium disilicate and resin cement, even when HF was applied.
Adhesives* ; Ceramics* ; Dental Porcelain ; Hydrofluoric Acid ; Lithium* ; Multivariate Analysis ; Polymerization ; Polymers ; Resin Cements ; Water

Ultrafiltration is one of the most fascinating technologies, which makes it possible to improve the quality of traditional medicines for application in the pharmaceutical industry. However, researchers have paid little attention to the effect of ultrafiltration membrane on traditional medicines chemical constituents. In this work, Ophiopogon japonicus (L.f) Ker-Gawl. was used as an example to illuminate the influence of ultrafiltration with different material and molecular weight cut-off (MWCO) membrane on natural chemical constituents as measured by ultra-fast liquid chromatography coupled with ion trap time-of-flight mass spectrometry (UFLC-IT-TOF/MS). Our results indicated that ultrafiltration membrane significantly impacted homoisoflavonoids, especially homoisoflavonoids that were almost completely retained on the polyethersulfone (PES) membrane. We also found that the larger number of aglycone hydroxy and sugar moiety in steroid saponins, the higher the transmittance. Furthermore, the passage rate (%) of ophiogenin type saponins was higher than that of others. The possible adsorptive mechanisms were hydrogen bonding, hydrophobic interactions, and benzene ring interaction by π-π stacking. In conclusion, it is crucial to choose appropriate ultrafiltration membrane based on the characteristics of produce products for application of ultrafiltration technique.
Chromatography, High Pressure Liquid ; methods ; Chromatography, Liquid ; methods ; Drugs, Chinese Herbal ; Isoflavones ; analysis ; Molecular Structure ; Molecular Weight ; Ophiopogon ; chemistry ; Plant Extracts ; chemistry ; Polymers ; Saponins ; analysis ; Spectrometry, Mass, Electrospray Ionization ; methods ; Sulfones ; Ultrafiltration ; methods

Deformities in tissues and organs can be treated by using tissue engineering approach offering the development of biologically functionalized scaffolds from a variety of polymer blends which mimic the extracellular matrix and allow adjusting the material properties to meet the defect architecture. In recent years, research interest has been shown towards the development of chitosan (CS) based biomaterials for tissue engineering applications, because of its minimal foreign body reactions, intrinsic antibacterial property, biocompatibility, biodegradability and ability to be molded into various geometries and forms thereby making it suitable for cell ingrowth and conduction. The present work involves the fabrication of nanofibrous scaffold from CS and poly(vinyl alcohol) blends by free-surface electrospinning method. The morphology and functional characteristics of the developed scaffolds were assessed by field emission scanning electron microscopy and fourier transformed infra-red spectra analysis. The morphological analysis showed the average fiber diameter was 269 nm and thickness of the mat was 200–300 µm. X-ray diffraction study confirmed the crystalline nature of the prepared scaffolds, whereas hydrophilic characteristic of the prepared scaffolds was confirmed by measured contact angle. The scaffolds possess an adequate biodegradable, swelling and mechanical property that is found desirable for tissue engineering applications. The cell study using umbilical cord blood-derived mesenchymal stem cells has confirmed the in vitro biocompatibility and cell supportive property of the scaffold thereby depicting their potentiality for future clinical applications.
Biocompatible Materials ; Chitosan ; Congenital Abnormalities ; Crystallins ; Extracellular Matrix ; Foreign Bodies ; Fourier Analysis ; Fungi ; In Vitro Techniques ; Mesenchymal Stromal Cells ; Methods ; Microscopy, Electron, Scanning ; Nanofibers* ; Polymers ; Tissue Engineering* ; Umbilical Cord ; X-Ray Diffraction

In this study, porous scaffolds were produced by a thermal crosslinking of polycaprolactone diacrylate in the presence of hydroxyapatite (HA) and particulate leaching technique with sodium chloride as the water soluble porogen for bone tissue engineering applications. The prepared scaffolds were characterized using techniques such as Field Emission Scanning Electron Microscopy, Differential Scanning Calorimetry, and Attenuated Total Reflectance-Fourier Transform Infrared Spectroscopy. Moreover, dynamic mechanical properties were investigated using Dynamic Mechanical Thermal Analysis. The obtained scaffolds present a porous structure with interconnected pores and porosity around 73%. It was found that the incorporation of HA particles to polycaprolactone (PCL) matrix resulted in an increased crystallinity. Moreover, both the storage modulus (E′) and glass transition temperature (T(g)) increased, while the loss factor (tan δ) decreased due to the hindrance of the HA particles to the mobility of polymer segments. Cytocompatability of the scaffolds was assessed by MTT assay and cell attachment studies. Osteoconductivity of the scaffolds was investigated with cells alkaline phosphatase extraction. The levels of alkaline phosphatase activity were found to be higher for PCL/HA network scaffold than for PCL network scaffold. In addition, cytocompatibility of the PCL/HA network scaffold indicated no toxicity, and cells were attached and spread to the scaffold walls.
Alkaline Phosphatase ; Bone and Bones* ; Calorimetry, Differential Scanning ; Crystallins ; Durapatite* ; Glass ; Microscopy, Electron, Scanning ; Polymers ; Porosity ; Sodium Chloride ; Spectrum Analysis ; Transition Temperature ; Water

PURPOSE: The aim of this study was to appraise the some mechanical properties of polymethyl methacrylate based denture base resin polymerized by copolymerization mechanism, and to investigate the cytotoxic effect of these copolymer resins. MATERIALS AND METHODS: 2-hydroxyethyl methacrylate (HEMA) and isobutyl methacrylate (IBMA) were added to monomers of conventional heat polymerized and injection-molded poly methyl methacrylate (PMMA) resin contents of 2%, 3%, and 5% by volume and polymerization was carried out. Three-point bending test was performed to detect flexural strength and the elasticity modulus of the resins. To determine the statistical differences between the study groups, the Kruskall-Wallis test was performed. Then pairwise comparisons were performed between significant groups by Mann-Whitney U test. Agar-overlay test was performed to determine cytotoxic effect of copolymer resins. Chemical analysis was determined by FTIR spectrum. RESULTS: Synthesis of the copolymer was approved by FTIR spectroscopy. Within the conventional heat-polymerized group maximum transverse strength had been seen in the HEMA 2% concentration; however, when the concentration ratio increased, the strength decreased. In the injection-molded group, maximum transverse strength had been seen in the IBMA 2% concentration; also as the concentration ratio increased, the strength decreased. Only IBMA showed no cytotoxic effect at low concentrations when both two polymerization methods applied while HEMA showed cytotoxic effect in the injection-molded resins. CONCLUSION: Within the limitations of this study, it may be concluded that IBMA and HEMA may be used in low concentration and at high temperature to obtain non-cytotoxic and durable copolymer structure.
Denture Bases ; Elastic Modulus ; Hot Temperature ; Polymerization* ; Polymers* ; Polymethyl Methacrylate ; Spectroscopy, Fourier Transform Infrared ; Spectrum Analysis

PURPOSE: The purpose of this preliminary study was to investigate the effects of adding 4,4'-bis(N,N-diethylamino) benzophenone (DEABP) as a co-initiator to a binary photoinitiating system (camphorquinone-amine) to analyze on the degree of conversion (DC) of a light-cured resin for dental 3D printing. MATERIALS AND METHODS: Cylindrical specimens (N=60, n=30 per group, o5 mm x 1 mm) were fabricated using bisphenol A glycerolate dimethacrylate (BisGMA) both with and without DEABP. The freshly mixed resins were exposed to light in a custom-made closed chamber with nine light-emitting diode lamps (wavelength: 405 nm; power: 840 mW/cm2) for polymerization at each incidence of light-irradiation at 10, 30, 60, 180, and 300 seconds, while five specimens at a time were evaluated at each given irradiation point. Fourier-transform infrared (FTIR) spectroscopy was used to measure the DC values of the resins. Two-way analysis of variance and the Duncan post hoc test were used to analyze statistically significant differences between the groups and given times (alpha=.05). RESULTS: In the DEABP-containing resin, the DC values were significantly higher at all points in time (P<.001), and also the initial polymerization velocity was faster than in the DEABP-free resin. CONCLUSION: The addition of DEABP significantly enhanced the DC values and, thus, could potentially become an efficient photoinitiator when combined with a camphorquinone-amine system and may be utilized as a more advanced photopolymerization system for dental 3D printing.
Glycerol ; Incidence ; Polymerization ; Polymers ; Spectrum Analysis

Most main oilfields in China have already entered a "double high" development stage (high water cut, high recovery degree). To further enhance oil recovery in reservoirs after polymer flooding (RAPFs), an efficient activator formulation for promoting metabolism of endogenous microorganism was studied by aerogenic experiments, physical simulation experiments, electron microscopy scanning and pyrophosphate sequencing. Results show that the activator could activate the endogenous microorganisms in the injected water and make the pressurized gas reach 2 MPa after 60 d static culture of the activator in a high pressure vessel. The oil recovery efficiency of natural core physical simulation flooding can be improved by more than 3.0% (OOIP) in RAPFs when injected 0.35 PV activator with 1.8% mass concentration, and a lot of growth and reproduction of activated endogenous microorganism in the core was observed by electron microscopy scanning. Field trial with 1 injector and 4 producers was carried out in the east of south II block of Sa Nan in December 2011. By monitoring four effective production wells, changes of carbon isotope δ13C (PDB) content of methane and carbon dioxide were -45 per thousand to -54 per thousand and 7 per thousand to 12 per thousand. Compared with east II of Sa Nan block, the oil amount increased by 35.9%, water cut stabled at 94%. The incremental oil was 5 957 t during the three and a half years, which provides an alternative approach for further improving oil recovery in similar reservoirs.
Carbon Dioxide ; chemistry ; Carbon Isotopes ; analysis ; China ; Diphosphates ; chemistry ; Methane ; chemistry ; Oil and Gas Fields ; microbiology ; Polymers ; Water ; Water Microbiology

OBJECTIVES: This study examined the influence of the resin thickness on the polymerization of silorane- and methacrylate-based composites. MATERIALS AND METHODS: One silorane-based (Filtek P90, 3M ESPE) and two methacrylate-based (Filtek Z250 and Z350, 3M ESPE) composite resins were used. The number of photons were detected using a photodiode detector at the different thicknesses (thickness, 1, 2 and 3 mm) specimens. The microhardness of the top and bottom surfaces was measured (n = 15) using a Vickers hardness with 200 gf load and 15 sec dwell time conditions. The degree of conversion (DC) of the specimens was determined using Fourier transform infrared spectroscopy (FTIR). Scratched powder of each top and bottom surface of the specimen dissolved in ethanol for transmission FTIR spectroscopy. The refractive index was measured using a Abbe-type refractometer. To measure the polymerization shrinkage, a linometer was used. The results were analyzed using two-way ANOVA and Tukey's test at p < 0.05 level. RESULTS: The silorane-based resin composite showed the lowest filler content and light attenuation among the specimens. P90 showed the highest values in the DC and the lowest microhardness at all depth. In the polymerization shrinkage, P90 showed a significantly lower shrinkage than the rest two resin products (p < 0.05). P90 showed a significantly lower refractive index than the remaining two resin products (p < 0.05). CONCLUSIONS: DC, microhardness, polymerization rate and refractive index linearly decreased as specimen thickness linearly increased. P90 showed much less polymerization shrinkage compared to other specimens. P90, even though achieved the highest DC, showed the lowest microhardness and refractive index.
Composite Resins ; Ethanol ; Hardness ; Photons ; Polymerization* ; Polymers* ; Refractometry ; Spectroscopy, Fourier Transform Infrared ; Spectrum Analysis

OBJECTIVES: The purpose of this study was to determine a separation method for each arsenic metabolite in urine by using a high performance liquid chromatography (HPLC)- inductively coupled plasma-mass spectrometer (ICP-MS). METHODS: Separation of the arsenic metabolites was conducted in urine by using a polymeric anion-exchange (Hamilton PRP X-100, 4.6 mm x 150 mm, 5 mum) column on Agilent Technologies 1260 Infinity LC system coupled to Agilent Technologies 7700 series ICP/MS equipment using argon as the plasma gas. RESULTS: All five important arsenic metabolites in urine were separated within 16 minutes in the order of arsenobetaine, arsenite, dimethylarsinate, monomethylarsonate and arsenate with detection limits ranging from 0.15 to 0.27 mug/L (40 muL injection). We used GEQUAS No. 52, the German external quality assessment scheme and standard reference material 2669, National Institute of Standard and Technology, to validate our analyses. CONCLUSIONS: The method for separation of arsenic metabolites in urine was established by using HPLC-ICP-MS. This method contributes to the evaluation of arsenic exposure, health effect assessment and other bio-monitoring studies for arsenic exposure in South Korea.
Argon ; Arsenic* ; Cacodylic Acid ; Chromatography, Liquid ; Environmental Monitoring ; Korea ; Limit of Detection ; Plasma ; Polymers ; Spectrum Analysis*