OBJECTIVE: To compare the cyclic fatigue resistance of nickel-titanium files made by 3 new heat treatment in simulated S-shaped root canals at different temperatures. METHODS: Gold heat-treated nickel-titanium files TruNatomy (25 mm, tip size 26#/0.04) and ProTaper Gold (25 mm, tip size 25#/0.08) were selected as the experimental group, M wire technique nickel-titanium file ProTaper Next (25 mm, tip size 25#/0.06) was selected as the control group. It was speculated that the Gold technique used in TruNatomy nickel-titanium file was R phase separation technique, which included a complete intermediate R-phase, increasing its flexibility. ProTaper Gold was a CM wire nickel-titanium file and the increased phase transformation temperature by heat treatment introduced martensite at room temperature, while it underwent gold heat treatment on the surface, generating an intermediate R phase during phase transformation, providing hyperelastic. ProTaper Next used M wire technique, M wire included austenite at room temperature, where heat mechanical processing introduced hardened martensite, which was incapable of participating phase transformation. Because of the lower elastic modulus of hardened martensite than austenite, the flexibility of the file was increased. Twenty instruments of each nickel-titanium file were submitted to the cyclic fatigue test by using a simulated canal with double curvatures at room tem-perature (24 ℃) and 65 ℃, 10 instruments of each nickel-titanium file were selected at each temperature (n=10). At the same temperature, the number of cyclic fatigue (NCF) and fragment length were analyzed by using One-Way analysis of variance at a significance level of P < 0.05. NCF and fragment length of the same nickel-titanium file at room temperature and 65 ℃ were compared by paired sample t test and the significance level was α=0.05. Fractured surfaces were analyzed by using scanning electron microscope. RESULTS: In double-curved canals, all the failure of the files due to cyclic fatigue was first seen in the apical curvature before the coronal curvature. At room temperature, in the apical curvature, NCF of TruNatomy was 344.4±96.6, ProTaper Gold was 175.0±56.1, ProTaper Next was 133.3±39.7, NCF of Tru Natomy was the highest (P < 0.05). In the coronal curvature, NCF of TruNatomy was 618.3± 75.3, ProTaper Gold was 327.5±111.8, ProTaper Next was 376.6±67.9, NCF of TruNatomy was also the highest (P < 0.05). There was no significant difference among the apical and coronal fragment length of the 3 nickel-titanium files (P>0.05). At 65 ℃, in the apical curvature, NCF of TruNatomy was 289.6±65.8, ProTaper Gold was 187.5±75.4, ProTaper Next was 103.0±38.5, NCF of TruNatomy was the highest (P < 0.05). In the coronal curvature, NCF of TruNatomy was 454.2±45.4, ProTaper Gold was 268.3±31.4, ProTaper Next was 283.8±31.7, NCF of TruNatomy was also the highest (P < 0.05). The apical fragment length of ProTaper Next was the highest (P < 0.05), and there was no significant difference among coronal fragment length of the 3 nickel-titanium files (P>0.05). Compared with room temperature, at 65 ℃, in the coronal curvature, NCF of TruNatomy decreased significantly (P < 0.05). The fractured surfaces of the three nickel-titanium files demonstrated typical cyclic fatigue. CONCLUSION Gold heat-treated nickel-titanium file had better cyclic fatigue resistance than M wire nickel-titanium file in S-shaped root canals.
Nickel/chemistry* ; Titanium/chemistry* ; Hot Temperature ; Root Canal Preparation/methods* ; Humans ; Materials Testing ; Gold/chemistry* ; Dental Alloys/chemistry* ; Stress, Mechanical

Rice stripe virus (RSV) causes dramatic losses in rice production worldwide. In this study, two monoclonal antibodies (MAbs) 16E6 and 11C1 against RSV and a colloidal gold-based immunochromatographic strip were developed for specific, sensitive, and rapid detection of RSV in rice plant and planthopper samples. The MAb 16E6 was conjugated with colloidal gold and the MAb 11C1 was coated on the test line of the nitrocellulose membrane of the test strip. The specificity of the test strip was confirmed by a positive reaction to RSV-infected rice plants and small brown planthopper (SBPH), and negative reactions to five other rice viruses, healthy rice plants, four other vectors of five rice viruses, and non-viruliferous SBPH. Sensitivity analyses showed that the test strip could detect the virus in RSV-infected rice plant tissue crude extracts diluted to 1:20 480 (w/v, g/mL), and in individual viruliferous SBPH homogenate diluted to 1:2560 (individual SPBH/μL). The validity of the developed strip was further confirmed by tests using field-collected rice and SBPH samples. This newly developed test strip is a low-cost, fast, and easy-to-use tool for on-site detection of RSV infection during field epidemiological studies and paddy field surveys, and thus can benefit decision-making for RSV management in the field.
Antibodies, Monoclonal/chemistry* ; China ; Chromatography, Affinity/methods* ; Collodion/chemistry* ; Colloids/chemistry* ; Gold Colloid/chemistry* ; Materials Testing ; Membranes, Artificial ; Oryza/virology* ; Plant Diseases/virology* ; Reproducibility of Results ; Sensitivity and Specificity ; Species Specificity ; Tenuivirus/isolation & purification*

In maxillofacial surgery, there is a significant need for the design and fabrication of porous scaffolds with customizable bionic structures and mechanical properties suitable for bone tissue engineering. In this paper, we characterize the porous Ti6Al4V implant, which is one of the most promising and attractive biomedical applications due to the similarity of its modulus to human bones. We describe the mechanical properties of this implant, which we suggest is capable of providing important biological functions for bone tissue regeneration. We characterize a novel bionic design and fabrication process for porous implants. A design concept of "reducing dimensions and designing layer by layer" was used to construct layered slice and rod-connected mesh structure (LSRCMS) implants. Porous LSRCMS implants with different parameters and porosities were fabricated by selective laser melting (SLM). Printed samples were evaluated by microstructure characterization, specific mechanical properties were analyzed by mechanical tests, and finite element analysis was used to digitally calculate the stress characteristics of the LSRCMS under loading forces. Our results show that the samples fabricated by SLM had good structure printing quality with reasonable pore sizes. The porosity, pore size, and strut thickness of manufactured samples ranged from (60.95± 0.27)% to (81.23±0.32)%, (480±28) to (685±31) μm, and (263±28) to (265±28) μm, respectively. The compression results show that the Young's modulus and the yield strength ranged from (2.23±0.03) to (6.36±0.06) GPa and (21.36±0.42) to (122.85±3.85) MPa, respectively. We also show that the Young's modulus and yield strength of the LSRCMS samples can be predicted by the Gibson-Ashby model. Further, we prove the structural stability of our novel design by finite element analysis. Our results illustrate that our novel SLM-fabricated porous Ti6Al4V scaffolds based on an LSRCMS are a promising material for bone implants, and are potentially applicable to the field of bone defect repair.
Alloys ; Bionics ; Bone Substitutes/chemistry* ; Bone and Bones/pathology* ; Compressive Strength ; Elastic Modulus ; Finite Element Analysis ; Humans ; Lasers ; Materials Testing ; Maxillofacial Prosthesis Implantation ; Porosity ; Pressure ; Printing, Three-Dimensional ; Prostheses and Implants ; Prosthesis Design ; Stress, Mechanical ; Surgery, Oral/instrumentation* ; Tissue Engineering/methods* ; Titanium/chemistry*

Arthroscopy ; adverse effects ; instrumentation ; methods ; Diagnostic Equipment ; adverse effects ; microbiology ; Disinfection ; methods ; Equipment Failure ; Humans ; Materials Testing ; methods ; Orthopedic Equipment ; adverse effects ; microbiology ; Postoperative Complications ; etiology ; prevention & control

Microarc oxidation (MAO) has become a promising technique for the surface modification of implants. Therefore, the aims of this study were to further quantitatively and qualitatively evaluate the osteointegration abilities of MAO-treated and smooth surface (SF) implants in vivo and to investigate the areas in which the superiority of MAO-treated implants are displayed. In a rabbit model, a comprehensive histomorphological, osteogenic, mineralizational, and integrative assessment was performed using light microscopy, fluorescence microscopy, confocal laser scanning microscopy, and radiographic analyses. Compared with the SF groups, the MAO-treated groups exhibited more active contact osteogenesis, as well as distant osteogenesis, under fluorescence examination, the mineral apposition rate was found to be greater for all of the MAO-treated implants, and the osteointegration index (OI) value was greater in the MAO-treated groups at different times. In conclusion, the calcium-rich amorphous layer created by MAO provided a better environment for osteointegration, with more active contact osteogenesis, a more rapid mineral apposition rate and greater OI values.
Animals ; Bone-Implant Interface ; physiology ; Dental Implantation, Endosseous ; methods ; Dental Implants ; Femur ; surgery ; Implants, Experimental ; Materials Testing ; Microscopy, Confocal ; Microscopy, Electron, Scanning ; Microscopy, Fluorescence ; Models, Animal ; Osseointegration ; physiology ; Oxidation-Reduction ; Rabbits ; Spectrometry, X-Ray Emission ; Surface Properties ; Titanium

OBJECTIVETo fabricate organic-inorganic composite tissue engineering scaffolds for reconstructing calcified cartilage layer based on three-dimensional (3D) printing technique.

METHODSThe scaffolds were developed by 3D-printing technique with highly bioactive calcium-magnesium silicate ultrafine particles of 1%, 3% and 5% of mass fraction, in which the organic phases were composed of type I collagen and sodium hyaluronate. The 3D-printed scaffolds were then crosslinked and solidified by alginate and CaCl₂ aerosol. The pore size and distribution of inorganic phase were observed with scanning electron microscope (SEM); the mechanical properties were tested with universal material testing machine, and the porosity of scaffolds was also measured.

RESULTSPore size was approximately (212.3 ± 34.2) μm with a porosity of (48.3 ± 5.9)%, the compressive modulus of the scaffolds was (7.2 ± 1.2) MPa, which was irrelevant to the percentage changes of calcium-magnesium silicate, the compressive modulus was between that of cartilage and subchondral bone.

CONCLUSIONThe porous scaffolds for calcified cartilage layer have been successfully fabricated, which would be used for multi-layered composite scaffolds in osteochondral injury.

Bioprinting ; Cartilage ; growth & development ; Materials Testing ; Porosity ; Printing, Three-Dimensional ; Tissue Engineering ; methods ; Tissue Scaffolds ; chemistry

We conducted this study to investigate the synergistic effect of human urine-derived stem cells (USCs) and surface modified composite scaffold for bladder reconstruction in a rat model. The composite scaffold (Polycaprolactone/Pluronic F127/3 wt% bladder submucosa matrix) was fabricated using an immersion precipitation method, and heparin was immobilized on the surface via covalent conjugation. Basic fibroblast growth factor (bFGF) was loaded onto the heparin-immobilized scaffold by a simple dipping method. In maximal bladder capacity and compliance analysis at 8 weeks post operation, the USCs-scaffold(heparin-bFGF) group showed significant functional improvement (2.34 ± 0.25 mL and 55.09 ± 11.81 microL/cm H2O) compared to the other groups (2.60 ± 0.23 mL and 56.14 ± 9.00 microL/cm H2O for the control group, 1.46 ± 0.18 mL and 34.27 ± 4.42 microL/cm H2O for the partial cystectomy group, 1.76 ± 0.22 mL and 35.62 ± 6.69 microL/cm H2O for the scaffold group, and 1.92 ± 0.29 mL and 40.74 ± 7.88 microL/cm H2O for the scaffold(heparin-bFGF) group, respectively). In histological and immunohistochemical analysis, the USC-scaffold(heparin-bFGF) group showed pronounced, well-differentiated, and organized smooth muscle bundle formation, a multi-layered and pan-cytokeratin-positive urothelium, and high condensation of submucosal area. The USCs seeded scaffold(heparin-bFGF) exhibits significantly increased bladder capacity, compliance, regeneration of smooth muscle tissue, multi-layered urothelium, and condensed submucosa layers at the in vivo study.
Adult Stem Cells/cytology/metabolism/*transplantation ; Animals ; Biocompatible Materials/chemistry ; Cell Differentiation ; Fibroblast Growth Factor 2/administration & dosage ; Heparin/administration & dosage ; Humans ; Materials Testing ; Models, Animal ; Poloxamer ; Polyesters ; Rats ; Reconstructive Surgical Procedures ; Regeneration ; Tissue Engineering/*methods ; Tissue Scaffolds/chemistry ; Urinary Bladder/anatomy & histology/physiology/*surgery ; Urine/*cytology

OBJECTIVETo evaluate the effect of microwave sintering on the translucency of zirconia and to compare these effect with those of conventional sintering. The relationship between the microstructure of specimens and translucency was investigated.

METHODSA total of 10 disc-shaped specimens were fabricated from 2 commercial brands of zirconia, namely, Zenostar and Lava. Each group included 5 discs. Conventional sintering was performed according to the manufacturers' specifications. The maximum temperature for Zenostar was 1,490 °C, whereas that for Lava was 1,500 °C. The dwelling time was 2 h. The sintering temperature for microwave sintering was 1,420 °C, heating rate was 15 °C · min⁻¹, and dwelling time was 30 min. After sintering, the translucency parameter (TP) of the specimens were measured with ShadeEye NCC. The sintered density of the specimens was determined by Archimedes' method. The grain size and microstructure of the specimens were investigated by scanning electron microscopy.

RESULTSDensity and translucency slightly increased by microwave sintering, but no significant difference was found between microwave and conventional sintering (P > 0.05). Small and uniform microstructure were obtained from microwave sintering. The mean TP of Lava was significantly higher than that of Zenostar (P < 0.001).

CONCLUSIONThe translucency of zirconia sintered by microwave sintering is similar to that of the zirconia sintered by conventional sintering.

Ceramics ; chemistry ; Dental Prosthesis Design ; methods ; Heating ; Materials Testing ; Microscopy, Electron, Scanning ; Microwaves ; Surface Properties ; Technology, Dental ; methods ; Zirconium ; chemistry

OBJECTIVETo investigate the impact of cuff pressure on airway leak pressure in laryngeal mask airway(LMA)Supreme and Flexible.

METHODSPatients about to have elective breast surgery were divided into Supreme group(35 cases)and Flexible group(33 cases). After general induction of anesthesia,LMA Supreme or Flexible was inserted by one anesthesiologist. We confirmed the LMA location,adjusted the cuff pressure,and recorded the peak airway leak pressures under different cuff pressures(10,20,30,40,and 50 cmH2O).

RESULTSIn Supreme group,peak airway leak pressures [(24.46±5.43),(25.11±5.51),(25.86±5.57),(26.17±5.72)cmH2O] under 20,30,40,and 50 cmH2O cuff pressure showed no significant difference(P>0.05)between each other,but significantly higher than that under 10 cmH2O cuff pressure(20.80±4.63)cmH2O(P<0.05). And in the Flexible group,peak airway leak pressures [(20.09±2.98),(20.70±3.08),(21.21±3.15)cmH2O] under 30,40,50 cmH2O cuff pressure also showed no significant difference(P>0.05)between each other,but significantly higher than those under 10 or 20 cmH2O cuff pressure [(17.52±2.39),(18.61±2.42)cmH2O]. Mean peak airway leak pressure [(25.40±5.52) cmH2O] of LMA Supreme was significantly higher than that of LMA Flexible(20.67±3.06)cmH2O(P<0.05).

CONCLUSIONSMean airway leak pressure of LMA Supreme is higher than LMA Flexible. The lowest cuff pressure to meet the tightness requirement with LMA Supreme is 20 cmH2O,which is lower than Flexible(30 cmH2O).

Air Pressure ; Anesthesia ; methods ; Humans ; Laryngeal Masks ; Materials Testing

This study examined the adhesive strength of two self-adhesive methacrylate resin-based sealers (MetaSEAL and RealSeal SE) to root dentin and compared them with RealSeal and AH Plus in properties. A total of 48 extracted human single-rooted teeth were used to prepare the 0.9-mm thick longitudinal tooth slice (each per tooth). Standardized simulated canal spaces of uniform dimensions were prepared in the middle of radicular dentin. After treated with 5.25% sodium hypochlorite (NaOCl) and 17% EDTA, tooth slices were allocated randomly to four groups (n=12) in terms of different sealers used: MetaSEAL, RealSeal SE, RealSeal, and AH plus groups. The simulated canal spaces were obturated with different sealers in each group. There were 10 slabs with 20 simulated canal spaces (n=20) used in each group for push-out testing. The failure modes and the ultrastructures of fractured sealer-dentin interfaces were examined. The remaining 2 slabs in each group underwent partial demineralization for observation of the ultrastructure of resin tags. The results showed that the push-out bond strength was 12.01±4.66 MPa in MetaSEAL group, significantly higher than that in the other three groups (P<0.05). Moreover, no statistically significant differences were noted in the push-out bond strength between RealSeal SE (5.43±3.68 MPa) and AH Plus (7.34±2.83 MPa) groups and between RealSeal SE and RealSeal (2.93±1.76 MPa) groups (P>0.05). Mixed failures were predominant in the fractured sealer-dentin interfaces in MetaSEAL and AH Plus groups, while adhesive failures were frequently seen in RealSeal SE and RealSeal groups. In conclusion, after complete removal of the smear layer, MetaSEAL showed superior bond ability to root dentin. The RealSeal SE is applicable in clinical practice, with its adhesive strength similar to that of AH Plus. The self-adhesive methacrylate resin-based sealer holds promise for use in endodontic treatment.
Adhesives ; standards ; Composite Resins ; standards ; Compressive Strength ; Dental Bonding ; Dental Pulp Cavity ; ultrastructure ; Dental Stress Analysis ; methods ; Dentin ; Dentin-Bonding Agents ; standards ; Epoxy Resins ; standards ; Humans ; Materials Testing ; methods ; Methacrylates ; standards ; Microscopy, Electron, Scanning ; Root Canal Filling Materials ; standards ; Root Canal Preparation ; Tooth Root