OBJECTIVE: To study microstructure, friction and wear behaviors of silicon-lithium spray coating on the surface of zirconia ceramics and to preliminarily evaluate its esthetic so as to provide support and guidance for the clinical application. METHODS: Zirconia ceramic specimens were randomly divided into three groups: coating group (two subgroups), polishing group (two subgroups), and glazing group (four subgroups), with 10 samples in each subgroup. The two subgroups of coating group were the zirconia ceramics with the untreated and preliminary polishing surfaces sprayed with silicon-lithium coating, respectively. The two subgroups of polishing group were preliminary polishing and fine polishing of zirconia ceramics, respectively. The four subgroups of glazing group were preliminarily polished zirconia ceramics glazed with Biomic and Stain/Glaze products, respectively; and untreated zirconia ceramics glazed with Biomic and Stain/Glaze products, respectively. The above 8 subgroups of zirconia ceramic specimens were used as friction pairs with 80 steatite ceramics for 50 000 chewing cycles under 50 N vertical load and artificial saliva lubrication using chewing simulation. Scanning electron microscope was used to observe the microstructure of the surface and section of the coating group, and the thickness of the coating and glazing were measured. The linear roughness of the coating and polishing groups was mea-sured using a laser confocal scanning microscope. Vickers hardness was measured using a microhardness tester and the esthetic of zirconia ceramic full crown sprayed with silicon-lithium coating was preliminarily evaluated. White light interferometer was used to measure the width, the maximum depth and the volume of the wear scars of each group, and the wear depth of steatite ceramics and wear rate of zirconia ceramic specimens were calculated. Kruskal-Wallis nonparametric test and Dunn's multiple comparisons test were used to analyze the wear depth of each group (α=0.05). RESULTS: The microstructures of the silica-lithium spray coatings on the untreated and preliminarily polished zirconia ceramic surfaces showed the protruding defects, and the line roughness of coating group was larger than that of the polishing group. The median thickness of the silica-lithium spray coating on the preliminarily polished zirconia ceramic was 13.0 μm (interquartile range, IQR: 11.6, 17.9), while that of the silica-lithium spray coating on the untreated zirconia ceramic was 4.4 μm (IQR: 4.1, 4.7). The Vickers hardness and wear rate of the coating group were between the polishing group and the glazing group. The wear depths of the wear scars of steatite ceramics were the glazing group, coating group, and polishing group in descending order, and there was statistically significant difference between glazing and polishing groups (P < 0.05). With the increase of polishing procedure, the wear depth of steatite ceramics decreased in each subgroups. The orders of maximum depth and volume of wear scars of zirconia ceramic were the glazing group, coating group, and polishing group in descending order, and there was statistically significant difference in the maximum depth of wear scars between glazing and polishing groups (P < 0.05). CONCLUSION The silica-lithium spray coating on the zirconia ceramic, can be used as a new method for zirconia ceramic surface treatment, because it can increase the esthetic of zirconia ceramics compared with polishing and reduce the wear of steatite ceramics compared with glazing.
Humans ; Silicon ; Materials Testing ; Friction ; Lithium ; Cicatrix ; Surface Properties ; Silicon Dioxide ; Zirconium/chemistry* ; Ceramics ; Dental Porcelain

Thyroid storm and thionamide-induced agranulocytosis are both rare and serious medical emergencies. We report a case of a patient in which these two rare events simultaneously occurred. A 33-year-old male, maintained on Methimazole for Graves’ Disease, presented with fever, throat pain, and uncontrolled thyrotoxic symptoms. Methimazole was promptly discontinued. Thyroid storm was alternatively treated with lithium, hydrocortisone, and propranolol. Agranulocytosis was managed supportively with GCSF and empiric antibiotics. Lithium was maintained until after radioablation. When thionamides are contraindicated, lithium is a viable option for the acute management of thyroid storm and a bridge to definitive therapy.
Methimazole ; Lithium

This paper introduces the distribution of global lithium resources and absorption, distribution, metabolism and excretion of lithium in the human body, discussing the positive effect of lithium in the environment on the nervous system and its neuroprotective mechanism. The tiny amounts of lithium that enter the body through the food chain have been linked to beneficial health effects, such as improved cognition and reduced depression and violence. However, the safe dose range of lithium is narrow, and the health effects of drinking high concentrations of lithium water in high-lithium areas are unclear. It is necessary to study the health effects and mechanisms of different doses of lithium, especially high concentrations of lithium in the environment.
Central Nervous System ; Humans ; Lithium ; Violence

BACKGROUND: Accumulating evidence suggests that lithium influences mesenchymal stem cell (MSC) proliferation and osteogenic differentiation. As decreased bone formation in femoral heads is induced by glucocorticoids (GCs), we hypothesized that lithium has a protective effect on GC-induced osteonecrosis of femoral heads (ONFH). METHODS: A rat ONFH model was induced by methylprednisolone (MP) and the effect of lithium chloride on the models was evaluated. Micro-computed tomography (CT)-based angiography and bone scanning were performed to analyze the vessels and bone structure in the femoral heads. Hematoxylin and eosin and immunohistochemical staining were performed to evaluate the trabecular structure and osteocalcin (OCN) expression, respectively. Bone marrow-derived MSCs were isolated from the models, and their proliferative and osteogenic ability was evaluated. Western blotting and quantitative real-time polymerase chain reaction were performed to detect osteogenic-related proteins including Runx2, alkaline phosphatase, and Collagen I. RESULTS: Micro-CT analysis showed a high degree of osteonecrotic changes in the rats that received only MP injection. Treatment with lithium reduced this significantly in rats that received lithium (MP + Li group); while 18/20 of the femoral heads in the MP showed severe osteonecrosis, only 5/20 in the MP + Li showed mild osteonecrotic changes. The MP + Li group also displayed a higher vessel volume than the MP group (0.2193 mm3vs. 0.0811 mm3, P < 0.05), shown by micro-CT-based angiography. Furthermore, histological analysis showed better trabecular structures and more OCN expression in the femoral heads of the MP + Li group compared with the MP group. The ex vivo investigation indicated higher proliferative and osteogenic ability and upregulated osteogenic-related proteins in MSCs extracted from rats in the MP + Li group than that in the MP group. CONCLUSIONS We concluded that lithium chloride has a significant protective effect on GC-induced ONFH in rats and that lithium also enhances MSC proliferation and osteogenic differentiation in rats after GC administration.
Animals ; Cell Differentiation ; Femur Head ; Femur Head Necrosis/drug therapy* ; Glucocorticoids ; Lithium Chloride ; Mesenchymal Stem Cells ; Osteogenesis ; Rats ; Rats, Sprague-Dawley ; X-Ray Microtomography

PURPOSE: To investigate the influence of crown material (lithium-disilicate, 3Y-TZP zirconia) and abutment type (rigid implant, resin tooth with artificial periodontium) on wear performance of their antagonist teeth and adjacent teeth.MATERIALS AND METHODS: A mandibular left first molar (#36) with adjacent human teeth (mandibular left second premolar: #35, mandibular left second molar: #37) and antagonistic human teeth (maxillary left second premolar: #25, maxillary left first molar: #26, maxillary left second molar: #27) was prepared simulating a section of the jaw. Samples were made with extracted human molars (Reference), crowned implants (Implant), or crowned resin tooth analogues (Tooth). Crowns (tooth #36; n = 16/material) were milled from lithium-disilicate (Li, IPS e.max CAD) or 3Y-TZP zirconia (Zr, IPS e.max ZirCAD, both Ivoclar Vivadent). Thermal cycling and mechanical loading (TCML) in the chewing simulator were applied simulating 15 years of clinical service. Wear traces were analyzed (frequency [n], depth [µm]) and evaluated using scanning electron pictures. Wear results were compared by one-way-ANOVA and post-hoc-Bonferroni (α = 0.05).RESULTS: After TCML, no visible wear traces were found on Zr. Li showed more wear traces (n = 30–31) than the reference (n = 21). Antagonistic teeth #26 showed more wear traces in contact to both ceramics (n = 27–29) than to the reference (n = 21). Strong wear traces (> 350 µm) on antagonists and their adjacent teeth were found only in crowned groups. Abutment type influenced number and depth of wear facets on the antagonistic and adjacent teeth.CONCLUSION: The clinically relevant model with human antagonistic and adjacent teeth allowed for a limited comparison of the wear situation. The total number of wear traces and strong wear on crowns, antagonistic and adjacent teeth were influenced by crown material.
Bicuspid ; Ceramics ; Crowns ; Humans ; Jaw ; Lithium ; Mastication ; Molar ; Tooth

BACKGROUND: Most studies have reported that suicide mortality rates are negatively associated with lithium levels in tap water; however, a few studies showed either no association or a positive association. Thus, the association between suicide mortality and lithium levels in tap water remains controversial. To clarify the association, our study evaluated the association between lithium levels in tap water and suicide mortality rates in Miyazaki Prefecture of Japan, after adjusting for confounding factors. METHODS: We measured lithium levels in tap water across the 26 municipalities of Miyazaki Prefecture in Japan. We examined the standardized mortality ratio (SMR) for suicide in each municipality and used the data as the average suicide SMRs over 5 years (2009-2013). Weighted least-squares regression analysis, adjusted for the size of each municipality's population, was used to investigate the association between lithium levels in tap water and suicide SMRs. In addition to a crude model, in an adjusted model, potential confounding factors (proportion of elderly people, proportion of one-person households, annual marriage rate, annual mean income, unemployment rate, the density of medical doctors per 100,000 people, annual total rainfall, and proportion of people with a college education or higher) were added as covariates. RESULTS: We showed that male and female suicide SMRs were not associated with lithium levels in tap water in Miyazaki Prefecture. After adjusting for confounders, male suicide SMRs were significantly and positively associated with the proportion of elderly people in the population and annual total rainfall, and female suicide SMRs were associated with the proportion of elderly people in the population. CONCLUSIONS No association between lithium levels in tap water and suicide mortality rates was found in Miyazaki Prefecture.
Drinking Water ; analysis ; Female ; Humans ; Japan ; Lithium ; analysis ; Male ; Suicide ; statistics & numerical data

A sensitive and simple liquid chromatography-tandem mass spectrometry method was developed and validated for the simultaneous quantification of ticagrelor and its active metabolite, AR-C124910XX from 50 µL human plasma using tolbutamide as an internal standard as per regulatory guidelines. Analytes in plasma were extracted by simple protein precipitation using acetonitrile, followed by chromatographic separation with an Acclaim™ RSLC 120 C₁₈ column (2.2 µm, 2.1 × 100 mm) and a gradient acetonitrile-water mobile phase containing 0.1% formic acid within 8 min. Mass spectrometric detection and quantitation were conducted by selected reaction-monitoring on a negative electrospray ionization mode with the following transitions: m/z 521.11 → 361.10, 477.03 → 361.10, and 269.00 → 169.60 for ticagrelor, AR-C124910XX, and tolbutamide, respectively. The lower limit of quantifications was 0.2 ng/mL with linear ranges of 0.2–2,500 ng/mL (r² ≥ 0.9949) for both analytes. All validation data, including selectivity, cross-talk, precision, accuracy, matrix effect, recovery, dilution integrity, stability, and incurred sample reanalysis, were well within acceptable limits. This assay method was validated using K₂-EDTA as the specific anticoagulant. Also, the anticoagulant effect was tested by lithium heparin, sodium heparin, and K₃-EDTA. No relevant anticoagulant effect was observed. This validated method was effectively used in the determination of ticagrelor and its active metabolite, AR-C124910XX, in plasma samples from patients with myocardial infarction.
Heparin ; Humans ; Lithium ; Mass Spectrometry ; Methods ; Myocardial Infarction ; Pharmacokinetics ; Plasma ; Tolbutamide

OBJECTIVES: Previous studies have revealed inconsistent results on amygdala volume in adult bipolar disorder (BD) patients compared to healthy controls (HC). Since the amygdala encompasses multiple subregions, the subtle volume changes in each amygdala nucleus might have not been fully reflected in the measure of the total amygdala volume, causing discrepant results. Thus, we aimed to investigate volume changes in each amygdala subregion and their association with subtypes of BD, lithium use and clinical status of BD. METHODS: Fifty-five BD patients and 55 HC underwent T1-weighted structural magnetic resonance imaging. We analyzed volumes of the whole amygdala and each amygdala subregion, including the anterior amygdaloid area, cortico-amygdaloid transition area, basal, lateral, accessory basal, central, cortical, medial and paralaminar nuclei using the atlas in the FreeSurfer. The volume difference was analyzed using a one-way analysis of covariance with individual volumes as dependent variables, and age, sex, and total intracranial volume as covariates. RESULTS: The volumes of whole right amygdala and subregions including basal nucleus, accessory basal nucleus, anterior amygdaloid area, and cortico-amygdaloid transition area in the right amygdala of BD patients were significantly smaller for the HC group. No significant volume difference between bipolar I disorder and bipolar II disorder was found after the Bonferroni correction. The trend of larger volume in medial nucleus with lithium treatment was not significant after the Bonferroni correction. No significant correlation between illness duration and amygdala volume, and insignificant negative correlation were found between right central nucleus volume and depression severity. CONCLUSIONS: Significant volume decrements of the whole amygdala, basal nucleus, accessory basal nucleus, anterior amygdaloid area, and cortico-amygdaloid transition area were found in the right hemisphere in adult BD patients, compared to HC group. We postulate that such volume changes are associated with altered functional activity and connectivity of amygdala nuclei in BD.
Adult ; Amygdala ; Basolateral Nuclear Complex ; Bipolar Disorder ; Cerebellar Nuclei ; Corticomedial Nuclear Complex ; Depression ; Humans ; Image Processing, Computer-Assisted ; Lithium ; Magnetic Resonance Imaging

PURPOSE: To evaluate the polishing effect on roughness and color change of pressed and layering ceramics after immersion in coffee solution.
Ceramics ; Coffee ; Diamond ; Immersion ; Lithium ; Microscopy, Electron, Scanning ; Pigmentation ; Spectrophotometry

PURPOSE: To investigate and compare the surface roughness (SR), weight and height of monolithic zirconia (MZ), ceramometal (CM), lithium disilicate glass ceramic (LD), composite resin (CR), and their antagonistic human teeth enamel. MATERIALS AND METHODS: 32 disc shaped specimens for the four test materials (n=8) and 32 premolars were prepared and randomly divided. SR, weight and height of the materials and the antagonist enamel were recorded before and after subjecting the specimens to 240,000 wear-cycles (49 N/0.8 Hz/5℃/50℃). SR, height, weight, and digital microscopic qualitative evaluation were measured. RESULTS: CM (0.23 + 0.08 µm) and LD (0.68 + 0.16 µm) exhibited the least and highest mean difference in the SR, respectively. ANOVA revealed significance (P=.001) between the materials for the SR. Paired T-Test showed significance (P < .05) for the pre- and post-SR for all the materials. For the antagonistic enamel, no significance (P=.987) was found between the groups. However, the pre- and post-SR values of all the enamel groups were significant (P < .05). Wear cycles had significant effect on enamel weight loss against all the materials (P < .05). CR and MZ showed the lowest and highest height loss of 0.14 mm and 0.46 mm, respectively. CONCLUSION: MZ and CM are more resistant to SR against the enamel than LD and CR. Enamel worn against test materials showed similar SR. Significant variations in SR values for the tested materials (MZ, LD, CM, and CR) against the enamel were found. Wear simulation significantly affected the enamel weight loss against all the materials, and enamel antagonist against MZ and CM showed more height loss.
Bicuspid ; Ceramics ; Dental Enamel ; Evaluation Studies as Topic ; Glass ; Humans ; Lithium ; Tooth ; Tooth Wear ; Weight Loss