Background: This study explores effective fixation methods for Pauwel type III femoral neck fractures by evaluating the biomechanical benefits of adding a screw to the Femoral Neck System (FNS). Methods: Computed tomography (CT) scans of an 82-year-old female patient with an intertrochanteric fracture were used to establish a finite element femur model with heterogeneous material properties. Finite element models of Pauwel type III fractures were created with and without an additional screw. The central and inferior trajectories of the FNS bolt were examined separately and combined with an additional screw for virtual fixation. Walking and stair-climbing loads were applied. Results: With the addition of a screw, both peak maximum and minimum principal strains consistently stayed comparable or decreased in models with both central and inferior bolt trajectories, while the volume of elements with principal strain exceeding 1% decreased by more than half. The peak von Mises stress observed in the implants ranged from 215.7 to 359.3 MPa, remaining below the titanium alloy's yield strength of 800 MPa. For normal walking, the addition of a screw to the central bolt trajectory model decreased the fracture gap by 50.6% and reduced sliding distance by 8.6%. For the inferior bolt trajectory, the gap was reduced by 57.9% and sliding distance by 25.0%.Under stair-climbing conditions, these improvements were also evident; the central trajectory model saw a halved fracture gap and a 7.9% decrease in sliding distance, while the inferior trajectory model experienced a 55.7% gap reduction and a 27.2% decrease in sliding distance. The additional screw increased the area ratio of the fracture site experiencing interfragmentary compression 34%–39%, while the additional screw alleviated peak interfragmentary compression by 12%–18% under both normal walking and stair-climbing conditions. Conclusions The addition of a screw reduced the fracture gap, sliding distance, and peak interfragmentary compression, while increasing the area ratio of interfragmentary compression under both walking and stair-climbing loads, regardless of the FNS bolt trajectory, suggesting a better mechanical environment for fracture healing.

Background: This study explores effective fixation methods for Pauwel type III femoral neck fractures by evaluating the biomechanical benefits of adding a screw to the Femoral Neck System (FNS). Methods: Computed tomography (CT) scans of an 82-year-old female patient with an intertrochanteric fracture were used to establish a finite element femur model with heterogeneous material properties. Finite element models of Pauwel type III fractures were created with and without an additional screw. The central and inferior trajectories of the FNS bolt were examined separately and combined with an additional screw for virtual fixation. Walking and stair-climbing loads were applied. Results: With the addition of a screw, both peak maximum and minimum principal strains consistently stayed comparable or decreased in models with both central and inferior bolt trajectories, while the volume of elements with principal strain exceeding 1% decreased by more than half. The peak von Mises stress observed in the implants ranged from 215.7 to 359.3 MPa, remaining below the titanium alloy's yield strength of 800 MPa. For normal walking, the addition of a screw to the central bolt trajectory model decreased the fracture gap by 50.6% and reduced sliding distance by 8.6%. For the inferior bolt trajectory, the gap was reduced by 57.9% and sliding distance by 25.0%.Under stair-climbing conditions, these improvements were also evident; the central trajectory model saw a halved fracture gap and a 7.9% decrease in sliding distance, while the inferior trajectory model experienced a 55.7% gap reduction and a 27.2% decrease in sliding distance. The additional screw increased the area ratio of the fracture site experiencing interfragmentary compression 34%–39%, while the additional screw alleviated peak interfragmentary compression by 12%–18% under both normal walking and stair-climbing conditions. Conclusions The addition of a screw reduced the fracture gap, sliding distance, and peak interfragmentary compression, while increasing the area ratio of interfragmentary compression under both walking and stair-climbing loads, regardless of the FNS bolt trajectory, suggesting a better mechanical environment for fracture healing.

Background: This study explores effective fixation methods for Pauwel type III femoral neck fractures by evaluating the biomechanical benefits of adding a screw to the Femoral Neck System (FNS). Methods: Computed tomography (CT) scans of an 82-year-old female patient with an intertrochanteric fracture were used to establish a finite element femur model with heterogeneous material properties. Finite element models of Pauwel type III fractures were created with and without an additional screw. The central and inferior trajectories of the FNS bolt were examined separately and combined with an additional screw for virtual fixation. Walking and stair-climbing loads were applied. Results: With the addition of a screw, both peak maximum and minimum principal strains consistently stayed comparable or decreased in models with both central and inferior bolt trajectories, while the volume of elements with principal strain exceeding 1% decreased by more than half. The peak von Mises stress observed in the implants ranged from 215.7 to 359.3 MPa, remaining below the titanium alloy's yield strength of 800 MPa. For normal walking, the addition of a screw to the central bolt trajectory model decreased the fracture gap by 50.6% and reduced sliding distance by 8.6%. For the inferior bolt trajectory, the gap was reduced by 57.9% and sliding distance by 25.0%.Under stair-climbing conditions, these improvements were also evident; the central trajectory model saw a halved fracture gap and a 7.9% decrease in sliding distance, while the inferior trajectory model experienced a 55.7% gap reduction and a 27.2% decrease in sliding distance. The additional screw increased the area ratio of the fracture site experiencing interfragmentary compression 34%–39%, while the additional screw alleviated peak interfragmentary compression by 12%–18% under both normal walking and stair-climbing conditions. Conclusions The addition of a screw reduced the fracture gap, sliding distance, and peak interfragmentary compression, while increasing the area ratio of interfragmentary compression under both walking and stair-climbing loads, regardless of the FNS bolt trajectory, suggesting a better mechanical environment for fracture healing.

Background: This study explores effective fixation methods for Pauwel type III femoral neck fractures by evaluating the biomechanical benefits of adding a screw to the Femoral Neck System (FNS). Methods: Computed tomography (CT) scans of an 82-year-old female patient with an intertrochanteric fracture were used to establish a finite element femur model with heterogeneous material properties. Finite element models of Pauwel type III fractures were created with and without an additional screw. The central and inferior trajectories of the FNS bolt were examined separately and combined with an additional screw for virtual fixation. Walking and stair-climbing loads were applied. Results: With the addition of a screw, both peak maximum and minimum principal strains consistently stayed comparable or decreased in models with both central and inferior bolt trajectories, while the volume of elements with principal strain exceeding 1% decreased by more than half. The peak von Mises stress observed in the implants ranged from 215.7 to 359.3 MPa, remaining below the titanium alloy's yield strength of 800 MPa. For normal walking, the addition of a screw to the central bolt trajectory model decreased the fracture gap by 50.6% and reduced sliding distance by 8.6%. For the inferior bolt trajectory, the gap was reduced by 57.9% and sliding distance by 25.0%.Under stair-climbing conditions, these improvements were also evident; the central trajectory model saw a halved fracture gap and a 7.9% decrease in sliding distance, while the inferior trajectory model experienced a 55.7% gap reduction and a 27.2% decrease in sliding distance. The additional screw increased the area ratio of the fracture site experiencing interfragmentary compression 34%–39%, while the additional screw alleviated peak interfragmentary compression by 12%–18% under both normal walking and stair-climbing conditions. Conclusions The addition of a screw reduced the fracture gap, sliding distance, and peak interfragmentary compression, while increasing the area ratio of interfragmentary compression under both walking and stair-climbing loads, regardless of the FNS bolt trajectory, suggesting a better mechanical environment for fracture healing.

BACKGROUND/OBJECTIVES: Accurate estimation of nutrient intake from food consumption requires reliable food composition data. However, since nutrient content changes during cooking, the application of raw ingredient composition may lead to overestimation, particularly for energy and fat in meat dishes. In this study, the suitability of applying cooked food codes for meat dishes to improve the validity of recipe-based nutrient content estimation was evaluated.MATERIALS/METHODS: Pork (thin-sliced and thick-cut belly and shoulder butt) and beef (tenderloin, loin, rib meat, and brisket point) were examined for cooking yield after grilling and their nutrient contents were estimated. Each cut was portioned to 100 g of raw meat and cooked in triplicate. Nutrient content was calculated using both raw and cooked meat codes from the Korean Standard Food Composition Table, and differences in energy, fat, and protein content were compared. RESULTS: When grilled under standardized conditions, the average cooking yield was approximately 65% for pork and 80% for beef (P < 0.0001). Thin slices of pork belly had a lower yield (62.6%) than thicker cuts (68.0%), while beef brisket point had the lowest yield among beef cuts (63.6%). Applying cooked meat codes and measured cooking yields resulted in overall decreases in energy (−10% to −50%) and fat (−20% to −60%) content, with slight increase in protein (up to +34%, P < 0.0001). For beef tenderloin, additional comparisons using matched raw and grilled data from the United States Department of Agriculture SR Legacy Database showed smaller percent differences in energy, fat, and protein than those obtained from the Korean database. CONCLUSION Incorporating measured cooking yields and corresponding cooked meat codes into recipe-based databases can improve the accuracy of nutrient intake estimation. The development of nutrient databases that reflect differences in cooking conditions—including temperature, duration, and doneness—should be prioritized to enhance the validity of national dietary surveys.

Objective: Primary frozen shoulder causes significant pain and progressively restricts shoulder movements. Diagnosis is made clinically based on patient history and physical examination. Management is mainly non-invasive owing to its self-limiting clinical course. However, clinical practice guidelines for frozen shoulder have not yet been developed in Korea. The developed guidelines aim to provide evidence-based recommendations for the diagnosis and treatment of frozen shoulder. Methods: A guideline development committee reviewed the literature from four databases (PubMed, Embase, Cochrane Library, and KMbase). Using the Population, Intervention, Comparator, and Outcome (PICO) framework, the committee formulated two backgrounds and 16 key questions to address common clinical concerns. Recommendations were made using the Grading of Recommendations, Assessment, Development, and Evaluation framework. Results: Diabetes, thyroid disease, and dyslipidemia significantly increase the risk of developing a frozen shoulder. Although frozen shoulder is often self-limiting, some patients may experience long-term functional disabilities. Ultrasound and magnetic resonance imaging should be used as adjunctive tools alongside clinical diagnosis, and rather than as independent diagnostic methods. Noninvasive approaches, such as medications, physical modalities, exercises, electrical stimulation, and manual therapy, may reduce pain and improve shoulder function. Other noninvasive interventions have limited evidence, and their application should be based on clinical judgment. Intra-articular steroid injections are recommended for treatment, and physiotherapy or hydrodilation with steroid injections can also be beneficial. Conclusion These guidelines provide evidence-based recommendations for diagnosing and treating primary frozen shoulder.

COVID-19 can lead to pulmonary complications, including organizing pneumonia.Steroids are essential in treating post-COVID-19 organizing pneumonia. However, research on the clinical benefits of initiating steroid treatment early for this condition is limited. To investigate the steroid initiation time in its association with treatment duration and corticosteroid dose for treating post-COVID-19 organizing pneumonia, we analyzed the data of 91 patients with post-COVID-19 organizing pneumonia at Chonnam National University Hospital between October 2020 and December 2022.Patients were categorized into early and late groups based on time from COVID-19 diagnosis to steroid initiation time for organizing pneumonia. The mean time interval between COVID-19 infection and steroid initiation time for treating organizing pneumonia, was 18.4±8.6 days. Within the early treatment group (treatment initiated ＜18.4 days after COVID-19), which included 55 patients, the mean duration of steroid treatment was 43.1±18.3days. In contrast, the late treatment group (initiated ≥18.4 days after COVID-19), which consisted of 36 patients, had a longer mean duration of steroid treatment 59.1±22.6 days) (p＜0.01). Regarding corticosteroid dosing, the early treatment group had an average dosage of 0.5±0.3 mg/kg/day, in contrast to the late group, which averaged 0.8±0.3 mg/kg/day (p＜0.01). Regression analysis showed steroid initiation time significantly influenced treatment duration (=0.80 , p＜0.01) and dosage (=0.03, p＜0.01). The clinical benefits of early steroid treatment for post-COVID-19 organizing pneumonia may lie in its association with reduced steroid treatment duration and dosage.

Background: The benefits of transradial access (TRA) over transfemoral access (TFA) for bifurcation percutaneous coronary intervention (PCI) are uncertain because of the limited availability of device selection. This study aimed to compare the procedural differences and the in-hospital and long-term outcomes of TRA and TFA for bifurcation PCI using secondgeneration drug-eluting stents (DESs). Methods: Based on data from the Coronary Bifurcation Stenting Registry III, a retrospective registry of 2,648 patients undergoing bifurcation PCI with second-generation DES from 21 centers in South Korea, patients were categorized into the TRA group (n = 1,507) or the TFA group (n = 1,141). After propensity score matching (PSM), procedural differences, in-hospital outcomes, and device-oriented composite outcomes (DOCOs; a composite of cardiac death, target vessel-related myocardial infarction, and target lesion revascularization) were compared between the two groups (772 matched patients each group). Results: Despite well-balanced baseline clinical and lesion characteristics after PSM, the use of the two-stent strategy (14.2% vs. 23.7%, P = 0.001) and the incidence of in-hospital adverse outcomes, primarily driven by access site complications (2.2% vs. 4.4%, P = 0.015), were significantly lower in the TRA group than in the TFA group. At the 5-year follow-up, the incidence of DOCOs was similar between the groups (6.3% vs. 7.1%, P = 0.639). Conclusion The findings suggested that TRA may be safer than TFA for bifurcation PCI using second-generation DESs. Despite differences in treatment strategy, TRA was associated with similar long-term clinical outcomes as those of TFA. Therefore, TRA might be the preferred access for bifurcation PCI using second-generation DES.

Background: During the coronavirus disease 2019 (COVID-19) pandemic, there was a shortage of medical resources and the need for proper treatment guidelines for brain tumor patients became more pressing. Thus, the Korean Society for Neuro-Oncology (KSNO), a multidisciplinary academic society, has undertaken efforts to develop a guideline that is tailored to the domestic situation and that can be used in similar crisis situations in the future. As part II of the guideline, this consensus survey is to suggest management options in specific clinical scenarios during the crisis period. Methods: The KSNO Guideline Working Group consisted of 22 multidisciplinary experts on neuro-oncology in Korea. In order to confirm a consensus reached by the experts, opinions on 5 specific clinical scenarios about the management of brain tumor patients during the crisis period were devised and asked. To build-up the consensus process, Delphi method was employed. Results: The summary of the final consensus from each scenario are as follows. For patients with newly diagnosed astrocytoma with isocitrate dehydrogenase (IDH)-mutant and oligodendroglioma with IDH-mutant/1p19q codeleted, observation was preferred for patients with low-risk, World Health Organization (WHO) grade 2, and Karnofsky Performance Scale (KPS) ≥60, while adjuvant radiotherapy alone was preferred for patients with high-risk, WHO grade 2, and KPS ≥60. For newly diagnosed patients with glioblastoma, the most preferred adjuvant treatment strategy after surgery was radiotherapy plus temozolomide except for patients aged ≥70 years with KPS of 60 and unmethylated MGMT promoters. In patients with symptomatic brain metastasis, the preferred treatment differed according to the number of brain metastasis and performance status. For patients with newly diagnosed atypical meningioma, adjuvant radiation was deferred in patients with older age, poor performance status, complete resection, or low mitotic count. Conclusion It is imperative that proper medical care for brain tumor patients be sustained and provided, even during the crisis period. The findings of this consensus survey will be a useful reference in determining appropriate treatment options for brain tumor patients in the specific clinical scenarios covered by the survey during the future crisis.