OBJECTIVE: To explore the role of antibiotic-eluting absorbable calcium sulfate in treating periprosthetic infection after one-stage revision of knee arthroplasty. METHODS: A retrospective analysis was performed on 36 patients(36 knees)who underwent phaseⅠrevision for periprosthesis infection after total knee arthroplasty from January 2018 to March 2022. All patients were underwent knee cavity puncture before operation and had positive results of aseptic body fluid culture, 21 patients received revision combined with antibiotic loaded calcium sulfate at stageⅠ(calcium sulfate group) during operation, and 15 patients underwent renovation at stageⅠ(revision group). There were 9 males and 12 females in calcium sulfate group, aged from 54 to 76 years old with an average of(67.6±6.2) years old. There were 15 patients in revision group, including 4 males and 11 females, aged from 60 to 75 years old with average of (69.6±4.1) years old. The levels of serum C-reactive protein (CRP), interleukin-6 (IL-6) at 7, 14, 30 and 90 days after operation were compared between two groups, and the rate of end-infection control at follow-up were compared. The systemic antibiotic application time, hospital stay and postoperative complications were observed between two groups. RESULTS: Calcium sulfate group were followed up for 12 to 29 months with an average of(18.9±4.2) months, and the infection control rate was 90.5%;while revision group were followed up 18 to 29 months with average of (21.6±3.7) months, and the infection control rate was 86.7% (13/15). There were no significant differences in follow-up time and infection control rate between two groups(P>0.05). Postoperative levels of CRP and IL-6 at 7, 14 and 30 days in calcium sulfate group were (32.79±11.48), (15.50±6.52), (9.36±3.32) mg·L^-1 and (17.31±6.15) pg·ml^-1, respectively;which were lower than those in revision group (40.65±11.32), (30.15±10.57), (18.97±5.86) mg·L^-1 and (25.54±6.73) pg·ml^-1, had statistical differences(P<0.05). There were no significant differences in IL-6 levels at 7 and 14 days after operation and CRP levels at 90 days after operation between two groups (P>0.05). The hospitalization time and systemic antibiotic application time in calcium sulfate group were (18.4±2.2) and (63.5±21.4) d, respectively;which were better than those in revision group (20.5±2.4) and (82.7±16.9) d, and had statistical differences(P<0.05). No significant wound complications and hypercalcemia were observed in calcium sulfate group. CONCLUSION Antibiotic eluted absorbable calcium sulfate could be used to treat periprosthetic knee infection, significantly reducing CRP levels in the early postoperative period, shortening hospital stay and systemic antibiotic application time, but it does not significantly improve the control rate of revision infection at stageⅠ.
Humans ; Male ; Female ; Aged ; Prosthesis-Related Infections/surgery* ; Middle Aged ; Calcium Sulfate/administration & dosage* ; Arthroplasty, Replacement, Knee/adverse effects* ; Retrospective Studies ; Anti-Bacterial Agents/therapeutic use* ; Interleukin-6/blood* ; C-Reactive Protein/metabolism* ; Reoperation ; Knee Prosthesis/adverse effects*

PURPOSE: End-stage knee osteoarthritis (OA) patients are the primary candidates for total knee arthroplasty (TKA). However, most morphological refinements of TKA prosthesis are based on anatomical data from the knees of healthy individuals. This study aimed to determine whether differences exist in key bony morphological characteristics of the distal femur and proximal tibia between osteoarthritic knees and healthy knees. METHODS: This was a retrospective cross-sectional observational study with a case-control design. Patients who were aged ≥ 50 years, had no history of trauma, fracture, or surgery in the studied knee, and had no obvious knee flexion contracture were included in this study by CT scans. Patients who met the American College of Rheumatology clinical criteria for knee OA were included in the study group. Kellgren-Lawrence grade III or IV knees were studied (for bilateral cases, the more severely affected knee was chosen). Patients who presented with unilateral knee pain or trauma were included in the control group, with CT scans from the opposite (asymptomatic) knee used for analyzing. The studied knee had a Kellgren-Lawrence grade of 0 or I and showed no abnormalities upon physical examination. Archived knee CT scans from 160 patients were divided into 2 groups: the study group (80 moderate-to-severe OA knees) and the control group (80 healthy knees). After 3-dimensional reconstruction and virtual cutting using a CT workstation, 13 morphological parameters of the distal femur and proximal tibia were compared between the 2 groups using independent-samples t-tests. RESULTS: No significant group differences in the femoral anteroposterior dimension (p = 0.797), height of the lateral femoral condyle (p = 0.268), posterior condylar angle (p = 0.240), tibial anteroposterior dimension (p = 0.536), or tibial lateral anteroposterior dimension (p = 0.702) were observed. However, the femoral mediolateral dimension (p = 0.002), distal femoral aspect ratio (femoral mediolateral dimension/femoral anteroposterior dimension) (p < 0.001), height of the femoral trochlear groove (p < 0.001), height of the medial femoral condyle (p < 0.001), tibial mediolateral dimension (p = 0.001), proximal tibial aspect ratio (tibial mediolateral dimension/tibial anteroposterior dimension) (p = 0.004), tibial medial anteroposterior dimension (p = 0.005), and tibial asymmetry ratio (tibial medial anteroposterior dimension/tibial lateral anteroposterior dimension) (p = 0.006) were all significantly greater in the study group. CONCLUSION Knees with moderate-to-severe OA are significantly wider than healthy knees, and OA is a risk factor for increased tibial platform asymmetry. When refining the morphological parameters of TKA prostheses, the specific bony morphological characteristics of OA knees should be taken into account to reduce the potential risk of femoral or tibial component underhang and facilitate optimal balance between tibial component fit and rotational alignment.
Humans ; Osteoarthritis, Knee/pathology* ; Male ; Female ; Cross-Sectional Studies ; Retrospective Studies ; Arthroplasty, Replacement, Knee ; Middle Aged ; Aged ; Case-Control Studies ; Prosthesis Design ; Knee Prosthesis ; Femur/anatomy & histology* ; Tibia/anatomy & histology* ; Tomography, X-Ray Computed ; Knee Joint/diagnostic imaging*

Compared with total knee arthroplasty, unicondylar knee replacement has the advantage of preserving the knee tissue structure and motor function to the greatest extent. Pre-clinical in-vitro test is an important tool to evaluate the safety and effectiveness of unicondylar knee prostheses, and it is also a key focus of the product registration process. Through collection, comparison, and analysis of current regulations, technical standards, guidelines, and related research literature, this paper expounds on the relevant research methods for the pre-clinical in-vitrotesting of unicondylar knee prostheses. At the same time, in conjunction with current evaluation requirements and experience, the study discusses the focus of pre-clinical performance research for unicondylar knee prostheses during the registration process to clarify the performance evaluation requirements of this product category. This aims to provide a reference for the pre-clinical performance research of unicondylar knee prostheses and to standardize industry testing standards.
Knee Prosthesis ; Arthroplasty, Replacement, Knee ; Humans ; Prosthesis Design ; Materials Testing

The wrist joint is a highly mobile functional joint. Wrist conditions including traumatic and degenerative arthritis, rheumatoid arthritis, and giant cell tumors of the distal radius, cause significant pain and mobility impairment. In joint surgery, the decision to use joint prostheses to reconstruct joint function is greatly influenced by the characteristics of the prosthesis (Mok et al., 2016). However, traditional implants have limitations such as shape mismatch, inadequate implant-bone interface strength which causes loosening, and poor bone ingrowth (Zhang et al., 2014).
Humans ; Joint Prosthesis ; Wrist Joint/surgery* ; Prosthesis Design ; Arthroplasty, Replacement ; Arthritis, Rheumatoid/surgery*

The reconstruction of the temporomandibular joint presents a multifaceted clinical challenge in the realm of head and neck surgery, underscored by its relatively infrequent occurrence and the lack of comprehensive clinical guidelines. This review aims to elucidate the available approaches for TMJ reconstruction, with a particular emphasis on recent groundbreaking advancements. The current spectrum of TMJ reconstruction integrates diverse surgical techniques, such as costochondral grafting, coronoid process grafting, revascularized fibula transfer, transport distraction osteogenesis, and alloplastic TMJ replacement. Despite the available options, a singular, universally accepted 'gold standard' for reconstructive techniques or materials remains elusive in this field. Our review comprehensively summarizes the current available methods of TMJ reconstruction, focusing on both autologous and alloplastic prostheses. It delves into the differences of each surgical technique and outlines the implications of recent technological advances, such as 3D printing, which hold the promise of enhancing surgical precision and patient outcomes. This evolutionary progress aims not only to improve the immediate results of reconstruction but also to ensure the long-term health and functionality of the TMJ, thereby improving the quality of life for patients with end-stage TMJ disorders.
Humans ; Temporomandibular Joint/surgery* ; Temporomandibular Joint Disorders/surgery* ; Transplantation, Autologous ; Arthroplasty, Replacement/methods* ; Joint Prosthesis ; Plastic Surgery Procedures/methods*

Prosthesis loosening is the leading cause of postoperative revision in unicompartmental knee arthroplasty (UKA). The deviation of medial and lateral translational installation of the prosthesis during surgery is a common clinical phenomenon and an important factor in increasing the risk of prosthesis loosening. This study established a UKA finite element model and a bone-prosthesis fixation interface micromotion prediction model. The predicted medial contact force and joint motion of the knee joint from a patient-specific lower extremity musculoskeletal multibody dynamics model of UKA were used as boundary conditions. The effects of 9 femoral component medial and lateral translational installation deviations on the Von Mises stress of the proximal tibia, the contact stress, and the micro-motion of the bone prosthesis fixation interface were quantitatively studied. It was found that compared with the neutral position (a/A of 0.492), the lateral translational deviation of the femoral component significantly increased the tibial Von Mises stress and the bone-prosthesis fixation interface contact stress. The maximum Von Mises stress and the maximum contact stress of the fixation interface increased by 14.08% and 143.15%, respectively, when a/A was 0.361. The medial translational deviation of the femoral component significantly increased the bone-prosthesis fixation interface micro-motion. The maximum value of micromotion under the conditions of femoral neutral and medial translation deviation was in the range of 20-50 μm, which is suitable for osseointegration. Therefore, based on considerations such as the micromotion range suitable for osseointegration reported in the literature, the risk of reducing prosthesis loosening, and factors that may induce pain, it is recommended that clinicians control the mounting position of the femoral component during surgery within the safe range of 0-4 mm medial translation deviation.
Humans ; Arthroplasty, Replacement, Knee/methods* ; Finite Element Analysis ; Biomechanical Phenomena ; Knee Prosthesis ; Tibia/surgery* ; Femur/surgery* ; Stress, Mechanical ; Prosthesis Failure ; Knee Joint/surgery* ; Prosthesis Design

The orientation of the acetabular cup in hip joint anteroposterior radiograph is a key factor in evaluating the postoperative outcomes of total hip arthroplasty (THA). Currently, measurement of the acetabular cup anteversion angle primarily relies on manual drawing of auxiliary lines by orthopedic surgeons and calculations using scientific calculators. This study proposes an automated computer-aided measurement method for the acetabular cup anteversion angle based on hip joint anteroposterior radiograph. The proposed method segments hip prosthesis images using an improved Otsu algorithm, identifies feature points at the acetabular cup opening by combining circle-fitting theory and the cup's geometric characteristics, and fits an ellipse to the cup opening to calculate the anteversion angle. A total of 104 hip joint anteroposterior radiographs, including 71 right-sided and 81 left-sided prostheses, were analyzed. Two orthopedic surgeons independently measured the postoperative anteversion angles, and the results were compared with computer-generated measurements for correlation analysis. Spearman and Pearson correlation analyses demonstrated significant correlations between the proposed method and manual measurements for both the right group ( r = 0.795, P < 0.01) and the left group ( r = 0.859, P < 0.01). This method provides a reliable reference for orthopedic surgeons to assess postoperative prognosis.
Humans ; Acetabulum/anatomy & histology* ; Arthroplasty, Replacement, Hip/methods* ; Algorithms ; Hip Prosthesis ; Hip Joint/diagnostic imaging* ; Radiography ; Image Processing, Computer-Assisted/methods*

Although metal blocks have been widely used for reconstructing uncontained tibial bone defects, the influence of their elastic modulus on the stability of tibial prosthesis fixation remains unclear. Based on this, a finite element model incorporating constrained condylar knee (CCK) prosthesis, tibia, and metal block was established. Considering the influence of the post-restraint structure of the prosthesis, the effects of variations in the elastic modulus of the block on the von Mises stress distribution in the tibia and the block, as well as on the micromotion at the bone-prosthesis fixation interface, were investigated. Results demonstrated that collision between the insert post and femoral prosthesis during tibial internal rotation increased tibial von Mises stress, significantly influencing the prediction of block elastic modulus variation. A decrease in the elastic modulus of the metal block resulted in increased von Mises stress in the proximal tibia, significantly reduced von Mises stress in the distal tibia, decreased von Mises stress of the block, and increased micromotion at the bone-prosthesis fixation interface. When the elastic modulus of the metal block fell below that of bone cement, inadequate block support substantially increased the risk of stress shielding in the distal tibia and fixation interface loosening. Therefore, this study recommends that biomechanical investigations of CCK prostheses must consider the post-constraint effect, and the elastic modulus of metal blocks for bone reconstruction should not be lower than 3 600 MPa.
Knee Prosthesis ; Humans ; Finite Element Analysis ; Tibia/surgery* ; Elastic Modulus ; Arthroplasty, Replacement, Knee/methods* ; Stress, Mechanical ; Metals ; Prosthesis Design ; Knee Joint/surgery* ; Biomechanical Phenomena

OBJECTIVE: To analyze the short-term effectiveness and safety of personalized three-dimensional (3D) printed customized prostheses in severe Paprosky type Ⅲ acetabular bone defects. METHODS: A retrospective analysis was conducted on 8 patients with severe Paprosky type Ⅲ acetabular bone defects and met the selection criteria between January 2023 and June 2024. There were 3 males and 5 females, with an average age of 64.6 years ranged from 56 to 73 years. All primary replacement prostheses were non-cemented, including 1 ceramic-ceramic interface, 1 ceramic-polyethylene interface, and 6 metal-polyethylene interfaces. The time from the primary replacement to the revision was 4 days to 18 years. The reasons for revision were aseptic loosening in 5 cases, revision after exclusion in 2 cases, and repeated dislocation in 1 case. The preoperative Harris score was 39.5±3.7 and the visual analogue scale (VAS) score was 7.1±0.8. The operation time, intraoperative blood loss, hospital stay, and complications were recorded. The hip function was evaluated by Harris score, and the degree of pain was evaluated by VAS score. The acetabular cup abduction angle, anteversion angle, rotational center height, greater trochanter height, and femoral offset were measured on X-ray film. RESULTS: The operation time was 95-223 minutes, with an average of 151.13 minutes. The intraoperative blood loss was 600-3 500 mL, with an average of 1 250.00 mL. The hospital stay was 13-20 days, with an average of 16.88 days. All 8 patients were followed up 2-12 months, with an average of 6.4 months. One patient had poor wound healing after operation, which healed well after active symptomatic treatment. One patient had lower limb intermuscular vein thrombosis, but no thrombosis was found at last follow-up. No serious complications such as aseptic loosening, infection, dislocation, and periprosthetic fracture occurred during the follow-up. At last follow-up, the Harris score was 72.0±6.2 and the VAS score was 1.8±0.7, which were significantly different from those before operation ( t=-12.011, P<0.001; t=16.595, P<0.001). On the second day after operation, the acetabular cup abduction angle ranged from 40° to 49°, with an average of 44.18°, and the acetabular cup anteversion angle ranged from 19° to 26°, with an average of 21.36°, which were within the "Lewinneck safety zone". There was no significant difference in the rotational center height, greater trochanter height, and femoral offset between the healthy side and the affected side ( P>0.05). CONCLUSION The use of personalized 3D printed customized prostheses for the reconstruction of severe Paprosky type Ⅲ acetabular bone defects can alleviate pain and enhances hip joint function, and have good postoperative prosthesis position, without serious complications and have good safety.
Humans ; Printing, Three-Dimensional ; Male ; Female ; Middle Aged ; Acetabulum/surgery* ; Aged ; Retrospective Studies ; Hip Prosthesis ; Prosthesis Design ; Arthroplasty, Replacement, Hip/instrumentation* ; Reoperation ; Treatment Outcome

OBJECTIVE: To investigate the effectiveness of digital three-dimensional (3D) printing osteotomy guide plate assisted total knee arthroplasty (TKA) in treatment of knee osteoarthritis (KOA) patients with femoral internal implants. METHODS: The clinical data of 55 KOA patients who met the selection criteria between July 2021 and October 2023 were retrospectively analyzed. Among them, 26 cases combined with femoral implants were treated with digital 3D printing osteotomy guide plate assisted TKA (guide plate group), and 29 cases were treated with conventional TKA (control group). There was no significant difference in gender, age, body mass index, side, Kellgren-Lawrence classification, preoperative visual analogue scale (VAS) score, Hospital for Special Surgery (HSS) knee score, knee range of motion, and other baseline data between the two groups ( P>0.05). The operation time, intraoperative blood loss, incision length, postoperative first ambulation time, surgical complications; VAS score, knee HSS score, knee range of motion before operation, at 1 week and 3 months after operation, and at last follow-up; distal femoral lateral angle, proximal tibial medial angle, hip-knee-ankle angle and other imaging indicators at last follow-up were recorded and compared between the two groups. RESULTS: The operation time, incision length, intraoperative blood loss, and postoperative first ambulation time in the guide plate group were significantly lower than those in the control group ( P<0.05). In the control group, there were 1 case of incision rupture and bleeding and 1 case of lower limb intermuscular venous thrombosis, which was cured after symptomatic treatment. There was no complication such as neurovascular injury, incision infection, or knee prosthesis loosening in both groups. Patients in both groups were followed up 12-26 months, with an average of 16.25 months. The VAS score, HSS score, and knee range of motion improved at each time point after operation in both groups, and further improved with time after operation, the differences were significant ( P<0.05). The above indicators in the guide plate group were significantly better than those in the control group at 1 week and 3 months after operation ( P<0.05), and there was no significant difference between the two groups at last follow-up ( P>0.05). At last follow-up, the distal femoral lateral angle, the proximal tibial medial angle, and the hip-knee-ankle angle in the guide plate group were significantly better than those in the control group ( P<0.05). CONCLUSION The application of digital 3D printing osteotomy guide plate assisted TKA in the treatment of KOA patients with femoral implants can simplify the surgical procedures, overcome limitations of conventional osteotomy guides, reduce surgical trauma, achieve individualized and precise osteotomy, and effectively restore lower limb alignment and knee joint function.
Humans ; Arthroplasty, Replacement, Knee/instrumentation* ; Osteoarthritis, Knee/surgery* ; Osteotomy/instrumentation* ; Male ; Retrospective Studies ; Female ; Printing, Three-Dimensional ; Femur/surgery* ; Middle Aged ; Bone Plates ; Range of Motion, Articular ; Aged ; Treatment Outcome ; Surgery, Computer-Assisted/methods* ; Knee Prosthesis ; Knee Joint/surgery* ; Operative Time