Background and Objectives: Clinical characteristics and outcomes in acute heart failure (AHF) vary by phenotype. We assessed phenotype-specific features, treatment patterns, and outcomes in a nationwide Korean cohort. Methods: The Korean Heart Failure III registry prospectively enrolled 7,351 AHF admissions at 47 hospitals. Among 6,777 patients with available left ventricular ejection fraction (EF), phenotypes were defined as heart failure with reduced EF (HFrEF, ≤40%), mildly reduced EF (HFmrEF,41–49%), or preserved EF (HFpEF, ≥50%). The primary endpoint was a 12-month composite of all-cause death or heart transplantation, evaluated from index admission and, among hospital survivors, from discharge. We used inverse probability weighting (multinomial generalized boosted models with stabilized, trimmed weights) and weighted Cox proportional-hazards models to estimate hazard ratios (HRs). Results: Phenotype distribution was 58.9% HFrEF, 13.6% HFmrEF, and 27.5% HFpEF. Crude 12-month composite rates from index admission were 13.4% (HFrEF), 12.7% (HFmrEF), and 16.8% (HFpEF). After weighting, from index admission, HFmrEF (HR, 0.892; 95% confidence interval [CI], 0.731–1.088) and HFpEF (HR, 1.101; 95% CI, 0.939–1.291) did not differ from HFrEF; from discharge, HFpEF had modestly higher risk (HR, 1.207; 95% CI, 1.008–1.445) whereas HFmrEF did not (HR, 1.039; 95% CI, 0.844–1.279). Hyponatremia and chronic kidney disease were consistent adverse markers, while angiotensin-converting enzyme inhibitor/ angiotensin II receptor blocker use at discharge was protective. Conclusions Across the EF spectrum, phenotypes showed distinct profiles and risk. Postdischarge risk was modestly higher in HFpEF, supporting phenotype-tailored care and systematic discharge optimization in Korean patients with AHF.

Excessive wear of the teeth, which causes functional, aesthetic problems, or sensitivity symptoms, is referred to as pathological wear. If this leads to the collapse of occlusion, extensive restoration is necessary to restore function and aesthetics.When restoring pathologically worn dentition, it is essential to identify the cause of the wear before determining treatment plan to get a favorable prognosis. In this case, a patient exhibited severe tooth wear with decreased vertical dimension and clinical, radiographic examination, and medical history indicated the pathological wear caused by a combination of factors. Consequently, full-mouth rehabilitation was indicated and the vertical occlusal height was determined considering the appropriate restorative space. Based on the causes of the wear, the restoration method, materials, and occlusal pattern were selected and successfully restored to normal occlusal state through full-mouth rehabilitation with zirconia full-veneered crowns.

Purpose: . The purpose of this study is to analyze the biomechanical differences in rotation angle-torque according to the type of implant and to compare the effects of contamination and sandblasting on the removal torque value (RTV) of abutment screws. Materials and methods: . For this study, an automated device for tightening and loosening implant screws was developed, and each 15 implant-abutment complexes of external and internal connection type were prepared, divided into three groups according to the surface treatment of the screw:control group (no treatment), experimental group-1 (artificial saliva contamination and chlorhexidine (CHX) rinsing), and experimental group-2 (artificial saliva contamination, CHX rinsing, and subsequent 50 µm Al 2 O 3 sandblasting). FirstRTV was measured for each group, followed by different post-treatment procedures for the screws, and then Second-RTV was measured. During the procedure, the removal torque value and rotation angle vs. time were recorded at a 20 data/s.A standardized protocol was followed for all the tightening and loosening procedures: screw was tightened with 30 Ncm torque and maintained for 5 s, and then rotated in the reverse direction until the torque value reached 0 Ncm. After 10min of rest period, the screws were loosened to initial point. Results: . Statistical analysis of measured data revealed that the internal connection type showed significantly higher First-RTV compared to the external connection type, however, no significant differences in Second-RTV were found. Both experimental groups 1and 2 showed a decrease in RTVs for both implant types, while the control group showed a decrease in RTV only for the internal type. The internal connection type required a significantly larger rotation angle during the tightening and loosening process. Conclusion . Within the limitations of this study, both artificial saliva contamination and CHX cleansing, as well as sandblasting, decreased RTV in both internal and external connection types. Internal connections were more susceptible to the effects of contaminants.

The occlusal collapse resulting from loss of posterior tooth support and attrition necessitates treatment aimed at restoring normal function and aesthetics.Particularly in cases where there is insufficient space for restoration, full mouth rehabilitation accompanied by increased vertical dimension is necessary. This case report presents a complete mouth rehabilitation of a patient with inadequate anterior restoration space due to loss of posterior tooth support, utilizing guided implant surgery, facial scan, virtual articulator, and jaw motion tracker.

Excessive wear of the teeth, which causes functional, aesthetic problems, or sensitivity symptoms, is referred to as pathological wear. If this leads to the collapse of occlusion, extensive restoration is necessary to restore function and aesthetics.When restoring pathologically worn dentition, it is essential to identify the cause of the wear before determining treatment plan to get a favorable prognosis. In this case, a patient exhibited severe tooth wear with decreased vertical dimension and clinical, radiographic examination, and medical history indicated the pathological wear caused by a combination of factors. Consequently, full-mouth rehabilitation was indicated and the vertical occlusal height was determined considering the appropriate restorative space. Based on the causes of the wear, the restoration method, materials, and occlusal pattern were selected and successfully restored to normal occlusal state through full-mouth rehabilitation with zirconia full-veneered crowns.

Purpose: . The purpose of this study is to analyze the biomechanical differences in rotation angle-torque according to the type of implant and to compare the effects of contamination and sandblasting on the removal torque value (RTV) of abutment screws. Materials and methods: . For this study, an automated device for tightening and loosening implant screws was developed, and each 15 implant-abutment complexes of external and internal connection type were prepared, divided into three groups according to the surface treatment of the screw:control group (no treatment), experimental group-1 (artificial saliva contamination and chlorhexidine (CHX) rinsing), and experimental group-2 (artificial saliva contamination, CHX rinsing, and subsequent 50 µm Al 2 O 3 sandblasting). FirstRTV was measured for each group, followed by different post-treatment procedures for the screws, and then Second-RTV was measured. During the procedure, the removal torque value and rotation angle vs. time were recorded at a 20 data/s.A standardized protocol was followed for all the tightening and loosening procedures: screw was tightened with 30 Ncm torque and maintained for 5 s, and then rotated in the reverse direction until the torque value reached 0 Ncm. After 10min of rest period, the screws were loosened to initial point. Results: . Statistical analysis of measured data revealed that the internal connection type showed significantly higher First-RTV compared to the external connection type, however, no significant differences in Second-RTV were found. Both experimental groups 1and 2 showed a decrease in RTVs for both implant types, while the control group showed a decrease in RTV only for the internal type. The internal connection type required a significantly larger rotation angle during the tightening and loosening process. Conclusion . Within the limitations of this study, both artificial saliva contamination and CHX cleansing, as well as sandblasting, decreased RTV in both internal and external connection types. Internal connections were more susceptible to the effects of contaminants.

The occlusal collapse resulting from loss of posterior tooth support and attrition necessitates treatment aimed at restoring normal function and aesthetics.Particularly in cases where there is insufficient space for restoration, full mouth rehabilitation accompanied by increased vertical dimension is necessary. This case report presents a complete mouth rehabilitation of a patient with inadequate anterior restoration space due to loss of posterior tooth support, utilizing guided implant surgery, facial scan, virtual articulator, and jaw motion tracker.

Excessive wear of the teeth, which causes functional, aesthetic problems, or sensitivity symptoms, is referred to as pathological wear. If this leads to the collapse of occlusion, extensive restoration is necessary to restore function and aesthetics.When restoring pathologically worn dentition, it is essential to identify the cause of the wear before determining treatment plan to get a favorable prognosis. In this case, a patient exhibited severe tooth wear with decreased vertical dimension and clinical, radiographic examination, and medical history indicated the pathological wear caused by a combination of factors. Consequently, full-mouth rehabilitation was indicated and the vertical occlusal height was determined considering the appropriate restorative space. Based on the causes of the wear, the restoration method, materials, and occlusal pattern were selected and successfully restored to normal occlusal state through full-mouth rehabilitation with zirconia full-veneered crowns.

Purpose: . The purpose of this study is to analyze the biomechanical differences in rotation angle-torque according to the type of implant and to compare the effects of contamination and sandblasting on the removal torque value (RTV) of abutment screws. Materials and methods: . For this study, an automated device for tightening and loosening implant screws was developed, and each 15 implant-abutment complexes of external and internal connection type were prepared, divided into three groups according to the surface treatment of the screw:control group (no treatment), experimental group-1 (artificial saliva contamination and chlorhexidine (CHX) rinsing), and experimental group-2 (artificial saliva contamination, CHX rinsing, and subsequent 50 µm Al 2 O 3 sandblasting). FirstRTV was measured for each group, followed by different post-treatment procedures for the screws, and then Second-RTV was measured. During the procedure, the removal torque value and rotation angle vs. time were recorded at a 20 data/s.A standardized protocol was followed for all the tightening and loosening procedures: screw was tightened with 30 Ncm torque and maintained for 5 s, and then rotated in the reverse direction until the torque value reached 0 Ncm. After 10min of rest period, the screws were loosened to initial point. Results: . Statistical analysis of measured data revealed that the internal connection type showed significantly higher First-RTV compared to the external connection type, however, no significant differences in Second-RTV were found. Both experimental groups 1and 2 showed a decrease in RTVs for both implant types, while the control group showed a decrease in RTV only for the internal type. The internal connection type required a significantly larger rotation angle during the tightening and loosening process. Conclusion . Within the limitations of this study, both artificial saliva contamination and CHX cleansing, as well as sandblasting, decreased RTV in both internal and external connection types. Internal connections were more susceptible to the effects of contaminants.

The occlusal collapse resulting from loss of posterior tooth support and attrition necessitates treatment aimed at restoring normal function and aesthetics.Particularly in cases where there is insufficient space for restoration, full mouth rehabilitation accompanied by increased vertical dimension is necessary. This case report presents a complete mouth rehabilitation of a patient with inadequate anterior restoration space due to loss of posterior tooth support, utilizing guided implant surgery, facial scan, virtual articulator, and jaw motion tracker.