OBJECTIVE: To analyze the cement flow in the abutment margin-crown platform switching structure by using the three-dimensional finite element analysis, in order to prove that whether the abutment margin-crown platform switching structure can reduce the inflow depth of cement in the implantation adhesive retention. METHODS: By using ANSYS 19.0 software, two models were created, including the one with regular margin and crown (Model one, the traditional group), and the other one with abutment margin-crown platform switching structure (Model two, the platform switching group). Both abutments of the two models were wrapped by gingiva, and the depth of the abutment margins was 1.5 mm submucosal. Two-way fluid structure coupling calculations were produced in two models by using ANSYS 19.0 software. In the two models, the same amount of cement were put between the inner side of the crowns and the abutments. The process of cementing the crown to the abutment was simulated when the crown was 0.6 mm above the abutment. The crown was falling at a constant speed in the whole process spending 0.1 s. Then we observed the cement flow outside the crowns at the time of 0.025 s, 0.05 s, 0.075 s, 0.1 s, and measured the depth of cement over the margins at the time of 0.1 s. RESULTS: At the time of 0 s, 0.025 s, 0.05 s, the cements in the two models were all above the abutment margins. At the time of 0.075 s, in Model one, the gingiva was squeezed by the cement and became deformed, and then a gap was formed between the gingiva and the abutment into which the cement started to flow. In Model two, because of the narrow neck of the crown, the cement flowed out from the gingival as it was pressed by the upward counterforce from the gingival and the abutment margin. At the time of 0.1 s, in Model one, the cement continued to flow deep inside with the gravity force and pressure, and the depth of the cement over the margin was 1 mm. In Model two, the cement continued to flow out from the gingival at the time of 0.075 s, and the depth of the cement over the margin was 0 mm. CONCLUSION When the abutment was wrapped by the gingiva, the inflow depth of cement in the implantation adhesive retention can be reduced in the abutment margin-crown platform switching structure.
Finite Element Analysis ; Cementation/methods* ; Gingiva ; Crowns ; Dental Abutments ; Dental Cements ; Dental Stress Analysis

Objectives: To study the design of nonmetallic crowns for deciduous molars by means of computer aided design and to analyze the key parameters of the nonmetallic crowns of deciduous molars using finite element method. Methods: The three-dimensional model of a mandibular second primary molar was constructed by using a micro-CT system. The thickness of the crown was limited to 0.5 mm and four different crown shapes (chamfer+anatomic, chamfer+non-anatomic, knife edge+anatomic and knife edge+non-anatomic) were designed. Then, the crown shape was limited as chamfer+non-anatomic and five different thicknesses of the crown (0.50, 0.75, 1.00, 1.25, 1.50 mm) were designed, and three different materials, including polyetherketoneketone (PEKK), polymethylmethacrylate (PMMA) resin and resin-infiltrated ceramic, were applied to make the crown. Stress distribution and fatigue of each component of the model under vertical and oblique loadings were analyzed by using finite element method. Non-axial retention analysis was performed on chamfer+non-anatomic crowns, made of PMMA resin, with thicknesses of 0.50, 0.75, 1.00, 1.25 and 1.50 mm. Results: Among the four crown shape designs, the chamfer+non-anatomic type crown showed the lowest von Mises stress and the highest safety factor. By comparing three different materials, the resin-infiltrated ceramic group showed obvious stress concentration on the buccal edge of the crown and the PEKK group showed stress concentration in the adhesive layer. Results of non-axial retention analysis showed that the torques required by the crowns with five thicknesses at the same rotation angle were as follows: 4 856.1, 4 038.1, 3 497.3, 3 256.3 and 3 074.3 N⋅m, respectively. The comparison of areas of the adhesives fracture among groups were as follows: 0.5 mm group < 0.75 mm group < 1.00 mm group < 1.25 mm group < 1.50 mm group. Conclusions: In the design of nonmetallic crowns for primary molars, the edge of the crown should be designed as chamfer, the shape of the inner crown should be non-anatomical and the minimum preparation amount of the occlusal surface should be 1.00 mm. Among the three materials, PMMA resin, of which elastic modulus is similar to the dentin and the dental adhesive, might be the most suitable material for the crowns of primary molars.
Ceramics ; Crowns ; Dental Stress Analysis/methods* ; Finite Element Analysis ; Molar

Biodynamics of mandibular angle fractures has been extensively discussed in the literature in search for the best way to fixate and expedite recovery of trauma patients. Pioneers like Michelet and Champy had the greatest impact on evolving of osteosynthesis in maxillofacial traumatology; they introduced their basic principles frequently used to describe the biomechanics of mandibular fixation. Their concept states when a physiologic load is applied on mandibular teeth a negative tension will be created at superior border and a positive pressure will appear at inferior border. These simple definitions are the basis for the advent of fixation modalities in mandibular angle fracture. This article sought to reassess these principals based on load location via finite elements method.
Biomechanical Phenomena ; Dental Stress Analysis ; Finite Element Analysis ; Fracture Fixation, Internal ; methods ; Humans ; Mandible ; physiopathology ; Mandibular Fractures ; physiopathology ; surgery ; Tooth ; physiology

In this study, we evaluate the influence of post surface pre-treatments on the bond strength of four different cements to glass fiber posts. Eighty extracted human maxillary central incisors and canines were endodontically treated and standardized post spaces were prepared. Four post pre-treatments were tested: (i) no pre-treatment (NS, control), (ii) sandblasting (SA), (iii) silanization (SI) and (iv) sandblasting followed by silanization (SS). Per pre-treatment, four dual-cure resin cements were used for luting posts: DMG LUXACORE Smartmix Dual, Multilink Automix, RelyX Unicem and Panavia F2.0. All the specimens were subjected to micro push-out test. Two-way analysis of variance and Tukey post hoc tests were performed (α=0.05) to analyze the data. Bond strength was significantly affected by the type of resin cement, and bond strengths of RelyX Unicem and Panavia F2.0 to the fiber posts were significantly higher than the other cement groups. Sandblasting significantly increased the bond strength of DMG group to the fiber posts.
Aluminum Oxide ; chemistry ; Composite Resins ; chemistry ; Curing Lights, Dental ; classification ; Cuspid ; pathology ; Dental Bonding ; Dental Etching ; methods ; Dental Materials ; chemistry ; Dental Stress Analysis ; instrumentation ; Glass ; chemistry ; Humans ; Incisor ; pathology ; Materials Testing ; Microscopy, Electron, Scanning ; Polymerization ; Post and Core Technique ; instrumentation ; Resin Cements ; chemistry ; Root Canal Preparation ; methods ; Self-Curing of Dental Resins ; methods ; Silanes ; chemistry ; Stress, Mechanical ; Surface Properties ; Tooth, Nonvital ; therapy

This study examined the adhesive strength of two self-adhesive methacrylate resin-based sealers (MetaSEAL and RealSeal SE) to root dentin and compared them with RealSeal and AH Plus in properties. A total of 48 extracted human single-rooted teeth were used to prepare the 0.9-mm thick longitudinal tooth slice (each per tooth). Standardized simulated canal spaces of uniform dimensions were prepared in the middle of radicular dentin. After treated with 5.25% sodium hypochlorite (NaOCl) and 17% EDTA, tooth slices were allocated randomly to four groups (n=12) in terms of different sealers used: MetaSEAL, RealSeal SE, RealSeal, and AH plus groups. The simulated canal spaces were obturated with different sealers in each group. There were 10 slabs with 20 simulated canal spaces (n=20) used in each group for push-out testing. The failure modes and the ultrastructures of fractured sealer-dentin interfaces were examined. The remaining 2 slabs in each group underwent partial demineralization for observation of the ultrastructure of resin tags. The results showed that the push-out bond strength was 12.01±4.66 MPa in MetaSEAL group, significantly higher than that in the other three groups (P<0.05). Moreover, no statistically significant differences were noted in the push-out bond strength between RealSeal SE (5.43±3.68 MPa) and AH Plus (7.34±2.83 MPa) groups and between RealSeal SE and RealSeal (2.93±1.76 MPa) groups (P>0.05). Mixed failures were predominant in the fractured sealer-dentin interfaces in MetaSEAL and AH Plus groups, while adhesive failures were frequently seen in RealSeal SE and RealSeal groups. In conclusion, after complete removal of the smear layer, MetaSEAL showed superior bond ability to root dentin. The RealSeal SE is applicable in clinical practice, with its adhesive strength similar to that of AH Plus. The self-adhesive methacrylate resin-based sealer holds promise for use in endodontic treatment.
Adhesives ; standards ; Composite Resins ; standards ; Compressive Strength ; Dental Bonding ; Dental Pulp Cavity ; ultrastructure ; Dental Stress Analysis ; methods ; Dentin ; Dentin-Bonding Agents ; standards ; Epoxy Resins ; standards ; Humans ; Materials Testing ; methods ; Methacrylates ; standards ; Microscopy, Electron, Scanning ; Root Canal Filling Materials ; standards ; Root Canal Preparation ; Tooth Root

The purpose of this study was to research the three-dimensional displacements of implant-supported cantilever fixed partial denture (CFPD) under oblique loading. One Beagle dog was used in this experiment. Two immediate implants of ITI were inserted in the mandible of the dog, and the implant-supported CFPD which used the implants as abutments was made in vitro fresh mandible. Then the digital laser speckle technique was employed to measure the three-dimensional displacements of CFPD under different oblique loading. We found that when an oblique loading was exerted on the pontic, the displacement increased with increasing of load. Under equal loading, the displacement of the abutment near to the pontic was smaller than that of the pontic but greater than that of the abut-ment far from the pontic. When oblique loading was exerted on the abutment, the displacement of the direct loaded abutment was greater than that of the other abutment and the pontic. Under the.eeual loading, the displacement of implant-supported CFPD of loading on pontic was greater than that of loading on abutments. The experiments demonstrated that implant-supported cantilever fixed partial denture (CFPD) is an effective and advisable therapy for totally? or partially edentulous patients. However, it is also suggested that the clinicians should avoid exerting oblique loading, especially the obliqe loading of the pontic when th e CPDF is used.
Animals ; Bite Force ; Dental Implant-Abutment Design ; Dental Stress Analysis ; methods ; Denture Design ; Denture, Partial, Fixed ; Dogs ; Imaging, Three-Dimensional ; Male ; Tooth Mobility

The purpose of this study was to investigate the three-dimensional displacement of the cantilever fixed partial denture (CFPD) under an oblique loading. One Beagle dog was used in this experiment. The CFPD, which used the second premolar and the first molar as abutments and the second molar as pontic, was made in vitro fresh mandible of the Beagle dog, and the digital laser speckle (DLS) technique was employed to measure the three-dimensional displacement of the CFPD under the oblique loading for the first time. We found that when an oblique loading was exerted on the pontic, the displacement of CFPD was the greatest, and the displacement of the abutment near the pontic was smaller than that of the pontic but greater than that of the abutment far from the pontic. We also found that when an oblique loading was exerted on the abutment, the displacement of the directly loaded abutment was greater than that of the other abutment and the pontic. Under the oblique loading, the displacement increased with increasing of load. The experiment demonstrated that it would be advisable for the clinicians to avoid oblique loading, especially the oblique loading of the pontic when using the CPDF. The DLS technique may be one kind of methods for measuring the three-dimensional displacements of the small and irregular objects.
Animals ; Bite Force ; Dental Abutments ; Dental Stress Analysis ; methods ; Denture Design ; Denture, Partial, Fixed ; Dogs ; Imaging, Three-Dimensional ; Lasers ; Male ; Mandible ; Occlusal Adjustment ; Tooth Mobility

The variation in hardness of enamel is a frequently used method to evaluate the influence of whiting materials on the enamel. The purpose of this study is to improve the veracity on the evaluation tests caused by the tooth itself with point selection method. Three kinds of testing point selection methods on enamel were carried out, i. e. random selection, grid measurement and symmetrical measurement, respectively. The selected points were used to measure the micro hardness by Vickers. The influence of the variation of tooth structure itself on the hardness measurements results can be reduced by using testing point selection methods of symmetry, and thus, the accuracy of the test method used in the evaluation of the influence of dental materials on tooth hardness will be guaranteed.
Animals ; Cattle ; Dental Enamel ; drug effects ; Dental Stress Analysis ; Dentin ; drug effects ; Hardness ; drug effects ; In Vitro Techniques ; Tooth Bleaching ; methods ; Tooth Crown ; drug effects

OBJEVTIVETo evaluate the effect of different restoration methods on fracture resistance of endodontically treated teeth.

METHODSFifty intact extracted maxillary first premolars were randomly divided into 5 groups. Medial-occlusal cavity models were established in all the test groups (B-E) according to the same standard, followed by treatments with defect exposure only, defect filling with light cured composite resin, indirect resin inlays, or light cured composite resin combined with Biosplint fiber. Each specimen was tested using a universal test machine at 1.00 mm/min until fracture and the fracture load was recorded. The load angle was 45 degree to the long axis of the teeth, and the load was pointed to the middle of the lingual surface on the buccal cusp. The fracture resistance was analyzed statistically.

RESULTSThe mean load to cause fracture of the samples in each group group A to E was 1.27∓0.41, 0.23∓0.17, 0.55∓0.31, 0.89∓0.40, and 0.98∓0.34 kN, respectively, showing significant differences between the groups.

CONCLUSIONThe fracture resistance of the teeth is reduced after endodontic therapy, but can be increased significantly by restoration with composite resin inlay or light cured composite resin combined with Biosplint fiber.

Bicuspid ; physiopathology ; Composite Resins ; chemistry ; Dental Materials ; chemistry ; Dental Restoration, Permanent ; methods ; Dental Stress Analysis ; Humans ; Inlays ; Maxilla ; Tooth Fractures ; physiopathology ; Tooth, Nonvital ; physiopathology ; therapy

The multi-piece post-crown technique is more effective in restoring residual root than other restoration techniques. Various types of adhesives have different material properties that affect restoration. Therefore, the choice of adhesive is particularly important for patients. However, the effect of different kinds of adhesives was not too precise by experimental methods when concerning about individual differences of teeth. One tooth root can only be restored with one type of adhesive in experiment. After the mechanical test, this tooth root cannot be restored with other adhesives. With the help of medical imaging technology, reverse engineering and finite element analysis, a molar model can be reconstructed precisely and restored using different types of adhesives. The same occlusal and chewing loads were exerted on the same restored residual root models with different types of adhesives separately. Results of von Mises stress analysis showed that the adhesives with low Young's modulus can protect the root canal effectively. However, a root canal concentration is apparently produced around the root canal orifice when chewing. Adhesives with large Young's modulus can buffer the stress concentration of the root canal orifice. However, the root canal tissue may be destroyed because the adhesive is too hard to buffer the load.
Crowns ; Dental Bonding ; Dental Cements ; Dental Pulp Cavity ; Dental Stress Analysis ; methods ; Elastic Modulus ; Finite Element Analysis ; Humans ; Post and Core Technique ; Tooth, Nonvital