OBJECTIVE: To establish a three-dimensional finite element model of a digital wire loop space maintainer for the mandible and primary tooth loss, in order to investigate the stress, deformation, and shear force experienced by patients with the loss of the second primary molar when wearing the wire loop space maintainer. METHODS: Cone beam computed tomography (CBCT) scans were performed on the patients to create a digital model of the mandible with the absence of the second primary molar using Mimics 21.0 software. A digital model integrating the crown's retention and the wire loop structure of the full crown and ring wire loop space maintainer was constructed using pediatric space maintainer design software, utilizing three different materials: cobalt-chromium alloy, polyether ether ketone (PEEK), and titanium alloy. In ANSYS Work Beach 2023 R2 software, vertical loads of 70 N, tilted 45° along the long axis of the tooth loads of 70 N, and a 10 N load on the surface of the wire loop were applied to the occlusal surfaces of models 46 and 84, simulating centric and lateral occlusions during chewing with the wire loop space maintainer in place. The stress states of the wire loop space maintainer and supporting teeth were analyzed. RESULTS: Under various loading conditions, the maximum principal stress of the ring wire loop space maintainer was significantly lower than that of the full crown. Stress contour maps indicated that the peak of the maximum principal stress occurred at the junction of the wire loop and crown structure, indicating that this area was more susceptible to fracture. The ring wire loop space maintainer made from PEEK material exhibited the lowest maximum shear stress on the internal organizational surfaces, with equivalent stresses of 23.18 MPa and 36.35 MPa for models 46 and 84, respectively. Stress contour maps demonstrated that the maximum stress on tooth 46 was located at its mesial, while the maximum stress on tooth 84 was situated near the root area on its distal, in contact with the wire loop space maintainer. CONCLUSION In cases of second primary molar loss, wearing the digital ring wire loop space maintainer can effectively distribute stress, and the ring wire loop space maintainer made from PEEK material reduces the stress experienced by supporting teeth to some extent, demonstrating its superiority in clinical application.
Finite Element Analysis ; Humans ; Tooth, Deciduous ; Cone-Beam Computed Tomography ; Space Maintenance, Orthodontic/methods* ; Imaging, Three-Dimensional ; Orthodontic Wires ; Dental Stress Analysis ; Mandible ; Stress, Mechanical

In this paper, a preliminary stress/strain analysis of the design structure of a nickel-titanium alloy patent foramen ovale occluder is conducted with the finite element simulation analysis method. In the analysis, solid structure modeling is carried out on three different specifications of domestic patent foramen ovale occluders. Referring to the test method of fatigue performance in inspection standard YY/T 1553-2017, an initial installation deformation is applied to the model, and then the fatigue displacement of 2 mm is applied to the sample to make the model fatigue deformation. The fatigue safety factors of each type of occluder are obtained by strain simulation analysis. The results indicate that the minimum fatigue safety factors of the three specifications of domestic patent foramen ovale occluders are 2.09, 2.35 and 2.06 respectively, which all meet the design of fatigue safety factor greater than 1. Among them, 1818 and 3030 specifications of patent foramen ovale occluders have close values in minimum fatigue safety factors, and both are lower than that of 1825 model. Therefore, it is recommended to carry out physical fatigue tests on both 1818 and 3030 specifications to further verify the fatigue performance of the products.
Finite Element Analysis ; Titanium ; Nickel ; Alloys ; Foramen Ovale, Patent ; Materials Testing ; Septal Occluder Device ; Stress, Mechanical

The periodontal ligament (PDL) plays a crucial role in transmitting and dispersing occlusal force, acting as mechanoreceptor for muscle activity during chewing, as well as mediating orthodontic tooth movement. It transforms mechanical stimuli into biological signals, influencing alveolar bone remodeling. Recent research has delved deeper into the biological and mechanical aspects of PDL, emphasizing the importance of understanding its structure and mechanical properties comprehensively. This review focuses on the latest findings concerning both macro- and micro- structural aspects of the PDL, highlighting its mechanical characteristics and factors that influence them. Moreover, it explores the mechanotransduction mechanisms of PDL cells under mechanical forces. Structure-mechanics-mechanotransduction interplay in PDL has been integrated ultimately. By providing an up-to-date overview of our understanding on PDL at various scales, this study lays the foundation for further exploration into PDL-related biomechanics and mechanobiology.
Periodontal Ligament/cytology* ; Humans ; Biomechanical Phenomena ; Mechanotransduction, Cellular/physiology* ; Stress, Mechanical

Mechanical ventilation (MV) is currently widely used in the treatment of respiratory failure and anesthesia surgery, and is a commonly used respiratory support method for critically ill patients; however, improper usage of MV can lead to ventilator-induced lung injury (VILI), which poses a significant threat to patient life. Alveolar epithelial cell (AEC) has the functions of mechanosensation and mechanotransduction. Physiological mechanical stretching is beneficial for maintaining the lineage homeostasis and normal physiological functions of AEC cells, while excessive mechanical stretching can cause damage to AEC cells. Damage to AEC cells is an important aspect in the occurrence and development of VILI. Understanding the effects of mechanical stretching on AEC cells is crucial for developing safe and effective MV strategies, preventing the occurrence of VILI, and improving the clinical prognosis of VILI patients. From the perspective of cell mechanics, this paper aims to briefly elucidate the mechanical properties of AEC cells, mechanosensation and mechanotransduction of mechanical stretching in AEC cells, and the injury and repair of AEC cells under mechanical stretch stimulation, and potential mechanisms with the goal of helping clinical doctors better understand the pathophysiological mechanism of VILI caused by MV, improve their understanding of VILI, provide safer and more effective strategies for the use of clinical MV, and provide theoretical basis for the prevention and treatment of VILI.
Humans ; Mechanotransduction, Cellular ; Ventilator-Induced Lung Injury ; Stress, Mechanical ; Alveolar Epithelial Cells ; Respiration, Artificial/adverse effects* ; Epithelial Cells ; Pulmonary Alveoli/cytology* ; Animals

OBJECTIVES: This study aims to analyze the biomechanics of three kinds of rigid internal fixation methods for condylar head fractures. METHODS: A three dimensional finite element model of the normal mandible was constructed. It was then used to prepare condylar head fracture finite element model and three kinds of rigid internal fixation finite element model (unilateral tension screw, bilateral tension screw, tension screw+titanium plate). The mechanical characteristics and changes of the mandible condyle under the same mechanical conditions were compared among the three different rigid internal fixation methods. RESULTS: The maximum equivalent stress and displacement of the non-free end of condyle under the rigid internal fixation method of unilateral tension screw were 71.03 MPa and 4.72 mm, respectively. The maximum equivalent stress and displacement of the free end of condyle were 78.45 MPa and 4.50 mm, respectively. The maximum stress of fracture suture was 3.27 MPa. The maximum equivalent stress and displacement of the non-free end of condyle under the rigid internal fixation method of bilateral tension screw were 70.52 MPa and 4.00 mm, respectively. The maximum equivalent stress and displacement of the free end of condyle were 72.49 MPa and 3.85 mm, respectively. The maximum stress of fracture suture was 2.33 MPa. The maximum equivalent stress and maximum displacement of the non-free end of condyle under the rigid internal fixation method of tension screw+titanium plate were 67.26 MPa and 2.66 mm, respectively. The maximum equivalent stress and maximum displacement of the free end of condyle were 69.66 MPa and 2.50 mm, respectively. The maximum stress of fracture suture was 2.18 MPa. CONCLUSIONS The tension screw+titanium plate rigid internal fixation method is the most conducive to biomechanical distribution for condylar head fractures.
Fracture Fixation, Internal/instrumentation* ; Mandibular Condyle/surgery* ; Biomechanical Phenomena ; Bone Screws ; Finite Element Analysis ; Humans ; Mandibular Fractures/surgery* ; Bone Plates ; Titanium ; Stress, Mechanical

OBJECTIVES: This study explores the differences in fluid flow within alveolar cancellous bone at various sites under orthodontic forces and elucidates the relationship between fluid shear stress and bone remodeling. These fin-dings lay the groundwork for understanding the biomechanical mechanisms of orthodontic tooth movement. METHODS: Stress relaxation tests were performed on human alveolar bone samples to determine material parameters by using the Prony series. An inverse model of alveolar bone was then developed for numerical simulations of fluid-structure interactions to calculate fluid flow within cancellous bone. Meanwhile, a rat model of tooth movement was established to investigate variations in bone remodeling speeds across different regions. RESULTS: The microstructural distribution of cancellous alveolar bone was similar in humans and rats. The bone volume fraction and trabecular thickness gradually decreased from root cervical region to root apical region, while the trabecular space gradually increased. Under the influence of orthodontic forces, fluid shear stress within cancellous bone showed spatial variability across different levels, with the highest shear stress occurring at the root apical region, ranging from 0 to 0.936 6 Pa. Additionally, the rat model of tooth movement indicated that bone remodeling occurred more rapidly at the root apical region. CONCLUSIONS Fluid stimulation has a remarkable effect on al-veolar bone remodeling, causing changes in the structure of alveolar bone and ultimately regulating the speed of structu-ral remodeling.
Bone Remodeling ; Animals ; Tooth Movement Techniques ; Rats ; Alveolar Process/physiology* ; Stress, Mechanical ; Humans ; Biomechanical Phenomena ; Cancellous Bone/physiology* ; Shear Strength

Prosthesis loosening is the leading cause of postoperative revision in unicompartmental knee arthroplasty (UKA). The deviation of medial and lateral translational installation of the prosthesis during surgery is a common clinical phenomenon and an important factor in increasing the risk of prosthesis loosening. This study established a UKA finite element model and a bone-prosthesis fixation interface micromotion prediction model. The predicted medial contact force and joint motion of the knee joint from a patient-specific lower extremity musculoskeletal multibody dynamics model of UKA were used as boundary conditions. The effects of 9 femoral component medial and lateral translational installation deviations on the Von Mises stress of the proximal tibia, the contact stress, and the micro-motion of the bone prosthesis fixation interface were quantitatively studied. It was found that compared with the neutral position (a/A of 0.492), the lateral translational deviation of the femoral component significantly increased the tibial Von Mises stress and the bone-prosthesis fixation interface contact stress. The maximum Von Mises stress and the maximum contact stress of the fixation interface increased by 14.08% and 143.15%, respectively, when a/A was 0.361. The medial translational deviation of the femoral component significantly increased the bone-prosthesis fixation interface micro-motion. The maximum value of micromotion under the conditions of femoral neutral and medial translation deviation was in the range of 20-50 μm, which is suitable for osseointegration. Therefore, based on considerations such as the micromotion range suitable for osseointegration reported in the literature, the risk of reducing prosthesis loosening, and factors that may induce pain, it is recommended that clinicians control the mounting position of the femoral component during surgery within the safe range of 0-4 mm medial translation deviation.
Humans ; Arthroplasty, Replacement, Knee/methods* ; Finite Element Analysis ; Biomechanical Phenomena ; Knee Prosthesis ; Tibia/surgery* ; Femur/surgery* ; Stress, Mechanical ; Prosthesis Failure ; Knee Joint/surgery* ; Prosthesis Design

This article aims to compare and analyze the biomechanical differences between wing-shaped titanium plates and traditional titanium plates in fixing acetabular anterior column and posterior hemi-transverse (ACPHT) fracture under multiple working conditions using the finite element method. Firstly, four sets of internal fixation models for acetabular ACPHT fractures were established, and the hip joint stress under standing, sitting, forward extension, and abduction conditions was calculated through analysis software. Then, the stress of screws and titanium plates, as well as the stress and displacement of the fracture end face, were analyzed. Research has found that when using wing-shaped titanium plates to fix acetabular ACPHT fractures, the peak stress of screws decreases under all working conditions, while the peak stress of wing-shaped titanium plates decreases under standing and sitting conditions and increases under forward and outward extension conditions. The relative displacement and mean stress of the fracture end face decrease under all working conditions, but the values are higher under forward and outward extension conditions. Wing-shaped titanium plates can reduce the probability of screw fatigue failure when fixing acetabular ACPHT fractures and can bear greater loads under forward and outward extension conditions, improving the mechanical stability of the pelvis. Moreover, the stress on the fracture end surface is more conducive to stimulating fracture healing and promoting bone tissue growth. However, premature forward and outward extension rehabilitation exercises should not be performed.
Titanium ; Bone Plates ; Humans ; Acetabulum/surgery* ; Fracture Fixation, Internal/methods* ; Biomechanical Phenomena ; Finite Element Analysis ; Bone Screws ; Fractures, Bone/surgery* ; Stress, Mechanical ; Working Conditions

Alveolar bone reconstruction simulation is an effective means for quantifying orthodontics, but currently, it is not possible to directly obtain human alveolar bone material models for simulation. This study introduces a prediction method for the equivalent shear modulus of three-dimensional random porous materials, integrating the first-order Ogden hyperelastic model to construct a computed tomography (CT) based porous hyperelastic Ogden model (CT-PHO) for human alveolar bone. Model parameters are derived by combining results from micro-CT, nanoindentation experiments, and uniaxial compression tests. Compared to previous predictive models, the CT-PHO model shows a lower root mean square error (RMSE) under all bone density conditions. Simulation results using the CT-PHO model parameters in uniaxial compression experiments demonstrate more accurate prediction of the mechanical behavior of alveolar bone under compression. Further prediction and validation with different individual human alveolar bone samples yield accurate results, confirming the generality of the CT-PHO model. The study suggests that the CT-PHO model proposed in this paper can estimate the material properties of human alveolar bone and may eventually be used for bone reconstruction simulations to guide clinical treatment.
Humans ; Tomography, X-Ray Computed/methods* ; Porosity ; Alveolar Process/physiology* ; Bone Density ; Computer Simulation ; Elasticity ; X-Ray Microtomography ; Stress, Mechanical ; Finite Element Analysis ; Models, Biological

In order to investigate the mechanical response of lumbar vertebrae during gait cycle in adolescents with idiopathic scoliosis (AIS), the present study was based on computed tomography (CT) data of AIS patients to construct model of the left support phase (ML) and model of the right support phase (MR), respectively. Firstly, material properties, boundary conditions and load loading were set to simulate the lumbar vertebra-pelvis model. Then, the difference of stress and displacement in the lumbar spine between ML and MR was compared based on the stress and displacement cloud map. The results showed that in ML, the lumbar stress was mostly distributed on the convex side, while in MR, it was mostly distributed on the concave side. The stress of the two types of stress mainly gathered near the vertebral arch plate, and the stress of the vertebral arch plate was transmitted to the vertebral body through the pedicle with the progress of gait. The average stress of the intervertebral tissue in MR was greater than that in ML, and the difference of stress on the convex and convex side was greater. The displacement of lumbar vertebrae in ML decreased gradually from L1 to L5. The opposite is true in MR. In conclusion, this study can accurately quantify the stress on the lumbar spine during gait, and may provide guidance for brace design and clinical decision making.
Humans ; Lumbar Vertebrae/diagnostic imaging* ; Scoliosis/diagnostic imaging* ; Adolescent ; Gait/physiology* ; Biomechanical Phenomena ; Tomography, X-Ray Computed ; Stress, Mechanical ; Female ; Male