BACKGROUND:Arthroscopic anchor repair has become the main treatment method for rotator cuff tears at present.Among them,the insertion status of the anchor is a key factor in the success or failure of the operation.However,currently,the impact of the insertion depth of the anchor on the stress of the bone tunnel and the anchor under different bone density conditions remains unclear.OBJECTIVE:To explore the stress distribution of the bone tunnel and the anchor when the insertion depth of the anchor varies under different bone density conditions by using three-dimensional finite element analysis technology.METHODS:The CT image data of the humerus of volunteers were collected,and the models of the humerus and the anchor were constructed by using Mimics,3-Matic,and Solidworks software.In 3-Matic,holes with distances of 0,2,4,6,and 8 mm from the surface of the humerus were respectively created at the same position of the humerus and assembled with the anchor.In Mimics,values were assigned based on the CT gray value to obtain a model with normal bone mass(T value ≥-1.0).The parameters were changed to construct models with reduced bone mass(-2.5＜T value＜-1.0)and osteoporosis(T value＜-2.5).In each model,a 70 N pulling force was applied to the anchor along the direction tangent to the inner edge of the bone tunnel.The stress distribution and magnitude of the bone tunnel and the anchor when inserted at different depths under different bone density conditions were observed.RESULTS AND CONCLUSION:(1)When the insertion depth was the same,as the bone density decreased,the maximum equivalent stress of the anchor increased,while the maximum equivalent stress of the bone tunnel decreased.(2)When the bone density was the same,as the insertion depth of the anchor increased,the maximum equivalent stress of the anchor decreased.When the insertion depth was 4 mm,the stress of the bone tunnel was the smallest and the distribution was relatively uniform.The stress of the anchor was mainly distributed around the lower anchor hole and the proximal thread,and the stress of the bone tunnel was mainly at the part in contact with the proximal thread.The increase in the insertion depth would change the uniformity and pattern of the stress distribution,while the bone density had a relatively small impact on the stress distribution pattern.(3)It is concluded that the bone density of the humerus is crucial for the anchor repair of rotator cuff tears.It is recommended that clinicians measure the bone density of the greater tuberosity of the humerus before the operation.Excessive insertion depth of the anchor does not significantly increase its stability.Clinicians can conduct personalized preoperative assessments by using the finite element analysis method in combination with the actual situation of patients to achieve the best surgical results.

BACKGROUND:The quadriceps strength of patients with osteoporosis and sarcopenia is significantly reduced,which can further reduce the function of the knee joint,affect the function of the lower limbs and even lead to a decrease in whole-body coordination.It is speculated that a reasonable quadriceps training program and personalized guidance are beneficial to the recovery of knee joint function in patients with osteoporosis and sarcopenia.OBJECTIVE:To observe the effect of short-term moderate-intensity resistance rehabilitation training on the mass and function of the quadriceps and knee joint function in patients with osteoporosis and sarcopenia.METHODS:Using the integrated physical examination and rehabilitation model,375 patients with osteoporosis and sarcopenia were screened at the Health Management Center of Shanghai Public Health Clinical Center.They underwent 12 weeks of combined/comprehensive exercise rehabilitation based on resistance exercise,including quadriceps resistance isotonic and isometric contraction training twice a week(3-5 sets each time,10-15 minutes per set)and aerobic exercise/balance exercise two or three times a week(30 minutes each time).Assessments and data collection were performed before rehabilitation training,12 weeks after rehabilitation training,and at follow-up 12 weeks after stopping rehabilitation training,mainly including knee joint range of motion and proprioception,quadriceps muscle strength,and cross-sectional area(magnetic resonance imaging results),pain,knee joint function(Hospital for Special Surgery score)and walking function("up-and-go"time and 6 m pace test results)as well as the patient's psychological status assessment.RESULTS AND CONCLUSION:All 375 patients completed 12 weeks of rehabilitation training and 12 weeks of follow-up without any adverse events.(1)Compared with before training,the patients' gait speed and knee range of motion increased significantly after 12 weeks of rehabilitation training(P＜0.01),the time of"stand-to-walk"decreased(P＜0.01),and the proprioception of the knee joint and the strength of the quadriceps femoris were significantly improved(P＜0.01);and at the follow-up visit 12 weeks after stopping training,the above indicators and functions of the patients were well maintained(P＞0.05).(2)Magnetic resonance imaging results showed that the effective cross-sectional area of the quadriceps femoris did not improve significantly after 12 weeks of rehabilitation training(P＞0.05);but the Hospital for Special Surgery score of knee joint function increased significantly(P＜0.01),and the visual analog pain scale score decreased significantly(P＜0.01),suggesting that this may be related to the improvement of quadriceps femoris quality by resistance rehabilitation training.(3)The results of the Hospital Anxiety and Depression Scale score showed that the anxiety and depression scores of the patients continued to decrease,both at 12 weeks of rehabilitation training and at 12 weeks after stopping training(P＜0.01).It is suggested that resistance rehabilitation training of the quadriceps can help patients with osteoporosis and sarcopenia to restore quadriceps muscle strength,increase range of motion,improve proprioception and joint stability,thereby enhancing knee joint function,reducing pain,improving depression and anxiety,and to a certain extent promoting the coordinated recovery of the musculoskeletal system.

BACKGROUND:One of the advantages of clear aligner treatment is molar distalization.However,tooth tilting movement and loss of anterior anchorage may occur during treatment.There are few studies on whether these problems can be improved by selecting clear aligners with different thicknesses and edges to improve the clinical treatment effect.OBJECTIVE:To analyze the control ability of clear aligners with different thickness and edges on the central incisor,lateral incisor,and second molar when pushing the maxillary second molar distally by three-dimensional finite element analysis.METHODS:Three-dimensional finite element analysis models of bilateral maxillary second molar distalization with clear aligner,maxillary dentition,periodontal ligament,and alveolar bone with different thicknesses and margins were established by Mimics,Geomagic Wrap,3-matic and SolidWorks software,respectively.There were 16 combinations of four thicknesses(0.4,0.5,0.625,and 0.75 mm)and four margins(scallop,straight,straight extension 2 mm and straight extension 4 mm).The data were imported into Ansys Workbench software for design and solution.The mean value,peak value and distribution of the periodontal ligament equivalent stress of the second molar,the equivalent stress and the maximum initial displacement of the second molar,and the control ability of each appliance on the second molar,central incisor,and lateral incisor were analyzed.RESULTS AND CONCLUSION:(1)The mean equivalent stress of periodontal ligament of the second molar,the equivalent stress of the second molar and the maximum initial displacement of the second molar increased with the extension of the appliance edge and the increase of the thickness of the appliance in the 16 groups of models.(2)When the thickness of appliances was the same,the maximum equivalent stress of the second molar in the linear appliance group was the highest,and the maximum equivalent stress of the second molar in the linear extended appliance group was greater than that in the scallop appliance group.When the edge of the appliance was the same,the periodontal ligament equivalent stress peak of the second molar increased with the increase of the thickness of the appliance.The equivalent stress distribution in the periodontal ligament of the second molar in the linear extendable appliance group was more uniform than that in the scallop appliance group and the linear appliance group.(3)When the thickness of the appliance was the same,the scallop-shaped appliance had the worst control on the second molar.When the edge of the appliance was the same,with the increase of the thickness of the appliance,the control of the second molar by the linear extender appliance was gradually stronger than that by the linear appliance.The control of the central incisor was stronger and more stable with the linear extended 2 mm appliance,while the control of the lateral incisor was stronger and more stable with the linear appliance.(4)The results showed that when using clear aligners to push molars distally,extending the edge of the appliance could improve the control of the molars and reduce the tilting movement of the teeth.The design of a straight extension margin of 2 mm for the central incisor and a straight edge for the lateral incisor can enhance the control of the anchorage incisor and reduce the labial inclination of the anterior teeth.

BACKGROUND:Arthroscopic anchor repair has become the main treatment method for rotator cuff tears at present.Among them,the insertion status of the anchor is a key factor in the success or failure of the operation.However,currently,the impact of the insertion depth of the anchor on the stress of the bone tunnel and the anchor under different bone density conditions remains unclear.OBJECTIVE:To explore the stress distribution of the bone tunnel and the anchor when the insertion depth of the anchor varies under different bone density conditions by using three-dimensional finite element analysis technology.METHODS:The CT image data of the humerus of volunteers were collected,and the models of the humerus and the anchor were constructed by using Mimics,3-Matic,and Solidworks software.In 3-Matic,holes with distances of 0,2,4,6,and 8 mm from the surface of the humerus were respectively created at the same position of the humerus and assembled with the anchor.In Mimics,values were assigned based on the CT gray value to obtain a model with normal bone mass(T value ≥-1.0).The parameters were changed to construct models with reduced bone mass(-2.5＜T value＜-1.0)and osteoporosis(T value＜-2.5).In each model,a 70 N pulling force was applied to the anchor along the direction tangent to the inner edge of the bone tunnel.The stress distribution and magnitude of the bone tunnel and the anchor when inserted at different depths under different bone density conditions were observed.RESULTS AND CONCLUSION:(1)When the insertion depth was the same,as the bone density decreased,the maximum equivalent stress of the anchor increased,while the maximum equivalent stress of the bone tunnel decreased.(2)When the bone density was the same,as the insertion depth of the anchor increased,the maximum equivalent stress of the anchor decreased.When the insertion depth was 4 mm,the stress of the bone tunnel was the smallest and the distribution was relatively uniform.The stress of the anchor was mainly distributed around the lower anchor hole and the proximal thread,and the stress of the bone tunnel was mainly at the part in contact with the proximal thread.The increase in the insertion depth would change the uniformity and pattern of the stress distribution,while the bone density had a relatively small impact on the stress distribution pattern.(3)It is concluded that the bone density of the humerus is crucial for the anchor repair of rotator cuff tears.It is recommended that clinicians measure the bone density of the greater tuberosity of the humerus before the operation.Excessive insertion depth of the anchor does not significantly increase its stability.Clinicians can conduct personalized preoperative assessments by using the finite element analysis method in combination with the actual situation of patients to achieve the best surgical results.

BACKGROUND:The quadriceps strength of patients with osteoporosis and sarcopenia is significantly reduced,which can further reduce the function of the knee joint,affect the function of the lower limbs and even lead to a decrease in whole-body coordination.It is speculated that a reasonable quadriceps training program and personalized guidance are beneficial to the recovery of knee joint function in patients with osteoporosis and sarcopenia.OBJECTIVE:To observe the effect of short-term moderate-intensity resistance rehabilitation training on the mass and function of the quadriceps and knee joint function in patients with osteoporosis and sarcopenia.METHODS:Using the integrated physical examination and rehabilitation model,375 patients with osteoporosis and sarcopenia were screened at the Health Management Center of Shanghai Public Health Clinical Center.They underwent 12 weeks of combined/comprehensive exercise rehabilitation based on resistance exercise,including quadriceps resistance isotonic and isometric contraction training twice a week(3-5 sets each time,10-15 minutes per set)and aerobic exercise/balance exercise two or three times a week(30 minutes each time).Assessments and data collection were performed before rehabilitation training,12 weeks after rehabilitation training,and at follow-up 12 weeks after stopping rehabilitation training,mainly including knee joint range of motion and proprioception,quadriceps muscle strength,and cross-sectional area(magnetic resonance imaging results),pain,knee joint function(Hospital for Special Surgery score)and walking function("up-and-go"time and 6 m pace test results)as well as the patient's psychological status assessment.RESULTS AND CONCLUSION:All 375 patients completed 12 weeks of rehabilitation training and 12 weeks of follow-up without any adverse events.(1)Compared with before training,the patients' gait speed and knee range of motion increased significantly after 12 weeks of rehabilitation training(P＜0.01),the time of"stand-to-walk"decreased(P＜0.01),and the proprioception of the knee joint and the strength of the quadriceps femoris were significantly improved(P＜0.01);and at the follow-up visit 12 weeks after stopping training,the above indicators and functions of the patients were well maintained(P＞0.05).(2)Magnetic resonance imaging results showed that the effective cross-sectional area of the quadriceps femoris did not improve significantly after 12 weeks of rehabilitation training(P＞0.05);but the Hospital for Special Surgery score of knee joint function increased significantly(P＜0.01),and the visual analog pain scale score decreased significantly(P＜0.01),suggesting that this may be related to the improvement of quadriceps femoris quality by resistance rehabilitation training.(3)The results of the Hospital Anxiety and Depression Scale score showed that the anxiety and depression scores of the patients continued to decrease,both at 12 weeks of rehabilitation training and at 12 weeks after stopping training(P＜0.01).It is suggested that resistance rehabilitation training of the quadriceps can help patients with osteoporosis and sarcopenia to restore quadriceps muscle strength,increase range of motion,improve proprioception and joint stability,thereby enhancing knee joint function,reducing pain,improving depression and anxiety,and to a certain extent promoting the coordinated recovery of the musculoskeletal system.

Objective: To establish an accurate and rapid typing method for Rh typing of samples from patients who have received recent blood transfusions by utilizing the difference in osmotic fragility between fresh and old red blood cells. Methods: A lysing solution suitable for destroying old RBCs was prepared. Sixty-one samples collected in our hospital in 2024 with Rh typing of double groups were treated with the lysing solution to remove the old allogeneic red blood cells while preserving the patient's own fresh red blood cells, followed by repeat Rh typing tests. Results: For 61 samples with Rh typing in double groups, 41 were accurately detected identified through the red blood cell lysis method, yielding an identification rate of 67.21%. No significant difference was observed compared to the detection rate of the commonly used capillary centrifugation modified method (χ =0.103, P>0.05). Conclusion: The red blood cell lysis method provides a novel and rapid experimental approach for clinical use in processing Rh-typed samples that are of double groups, thereby offering a basis for Rh compatibility blood transfusion.

Functional dyspepsia （FD） is a prioritized disease category where traditional Chinese medicine （TCM） demonstrates distinct therapeutic advantages. The current western medicine treatment for FD is mainly based on proton pump inhibitors and prokinetic agents， with digestive enzymes， probiotics and antidepressants serving as adjuvant medication， yet such therapies still have certain limitations. TCM treatment for FD includes oral administration of Chinese herbal formulas and Chinese patent medicines， as well as external TCM therapies such as acupuncture and moxibustion， acupoint application， hot medicinal compress therapy， rubbing with ointment， medicinal iontophoresis， auricular acupoint therapy and tui na （Chinese medical massage）. The combined treatment of FD with integrated TCM and western medicine can significantly improve clinical effectiveness and reduce adverse reactions. The common mechanisms underlying the therapeutic effects of both TCM and western medicine revolve around the core pathological processes of FD， mainly focusing on restoring gastrointestinal motility， regulating the levels of brain-gut peptides， modulating intestinal microecology， and ameliorating inflammatory status. The differential mechanisms lie in the precise targeting feature of western medicine versus the holistic-regulating and multi-target characteristics of TCM， and the two approaches exert a synergistic effect to enhance efficacy. This paper proposes to leverage the advantages of TCM in holistic regulation and the strengths of western medicine in targeted treatment， so as to provide personalized and comprehensive treatment regimens for FD patients.

ObjectiveTo systematically evaluate the methodological quality and measurement properties of traditional Chinese medicine （TCM） syndrome efficacy evaluation scales， and to provide evidence-based references for selecting high-quality assessment tools in TCM clinical practice. MethodsChina National Knowledge Infrastructure （CNKI）， Wanfang Data， VIP Database， Chinese Biomedical Literature Database （CBM）， PubMed， the Cochrane Library， Embase， and Web of Science were searched from inception to April 2， 2025， for studies evaluating the measurement properties of TCM syndrome efficacy evaluation scales. Data were extracted， and the methodological quality and measurement properties of the included scales were assessed according to the consensus-based standards for the selection of health measurement instruments （COSMIN）. Recommendation levels were formulated based on the grading of evidence. ResultsA total of 46 studies were included， involving 22 generic syndrome efficacy evaluation scales and 24 disease-specific syndrome efficacy evaluation scales. None of the scales reported cross-cultural validity or measurement error. According to the recommendation grades， 2 scales met Grade A recommendations and are suggested for clinical use； 38 scales were classified as Grade B， indicating potential applicability but requiring further validation； and 6 scales were classified as Grade C， suggesting the need for further refinement. ConclusionExisting TCM syndrome efficacy evaluation scales exhibit substantial variability in methodological quality， incomplete reporting of measurement properties， and insufficient attention to scale revision. Future efforts should emphasize standardized design in the development of TCM syndrome scales， strengthen validation procedures for key measurement properties， and prioritize dynamic revision of scales， thereby providing high-quality tools to support the precise evaluation of syndrome efficacy.

AIM: To investigate variation patterns of corneal biomechanical parameters and binocular symmetry among children of different genders aged 8-16 years.METHODS:A retrospective study was conducted, and children who underwent optometric examinations at the ophthalmology department of our hospital were enrolled between January 2022 and December 2024. Measurements included the flat keratometry(K1), steep keratometry(K2), and mean curvature(Km)of the anterior corneal surface, horizontal visible iris diameter(HVID), central corneal thickness(CCT), corneal endothelial cell density(CECD), average cell size(ACS), coefficient of variation(CV), and hexagonality(HEX). Corneal parameters and binocular differences were compared between genders and across age groups.RESULTS:A total of 621 children(1 242 eyes)were enrolled in this study, including 284 males(568 eyes), 337 females(674 eyes), 528 children aged 8-12 years(1 056 eyes), and 93 children aged 13-16 years(186 eyes). In children aged 8-16 years, the K1, K2, Km and CV of both eyes, as well as the interocular CCT differences in boys were significantly lower than those in girls(all P<0.05), while the HVID and HEX of both eyes, as well as the CCT of the left eye in boys were significantly higher than those in girls(all P<0.05). Children aged 8-12 years had significantly higher K1, Km, CECD and HEX in both eyes, and significantly lower ACS in both eyes than those aged 13-16 years(all P<0.05). K1, K2, Km, CECD and HEX in both eyes were negatively correlated with age(P<0.05); ACS in both eyes was positively correlated with age(P<0.001); K1 and Km of the right eye were positively correlated with the CECD of the right eye(P<0.05), and K1 and CCT of the left eye were positively correlated with the CECD of the left eye(P<0.05).CONCLUSION:Significant gender differences exist in corneal parameters among children aged 8 to 16 years, while binocular symmetry remained stable.

Objective To investigate the dietary structure and nutritional metabolism indicators in patients with type 2 diabetic nephropathy and to analyze the relationship with renal injury. Methods From January 2022 to February 2024, 296 patients with type 2 diabetic nephropathy were included in the hospital for investigation. According to the measurement results of 24h urinary protein quantification, these patients were divided into mild, moderate and severe renal injury groups. The diet, nutritional metabolism and renal injury indicators were compared, and the correlation was analyzed. Results The total energy intake, protein, fat and carbohydrate energy supply ratio were decreased with the aggravation of renal injury while the levels of hemoglobin (Hgb), total protein (TP), globulin (GLB), albumin (ALB), triglyceride (TG) and high density lipoprotein cholesterol (HDL-C) were enhanced (P<0.05), and the total cholesterol (TC) and low density lipoprotein cholesterol (LDL-C) were manifested as severe injury group>moderate injury group>mild injury group (P<0.05). Total intake, carbohydrate energy supply ratio, Hgb, TP, GLB, ALB, TG and HDL-C were positively correlated with 24h urinary protein quantification, and the other indicators were negatively correlated with 24h urinary protein quantification (P<0.05). Conclusion The patients with type 2 diabetic nephropathy generally have unreasonable dietary structure and poor nutritional metabolism, both of which are associated with the degree of renal injury. It is recommended to strengthen the diet management, optimize the energy supply ratio, monitor the biochemical indicators and adjust the treatment regimen.