BACKGROUND:Lumbar degenerative disease is a disease of the musculoskeletal system that primarily affects the intervertebral structures,and the disease is treated with lumbar fusion and disc replacement.OBJECTIVE:To conduct comparative analysis of the differences between lumbar fusion,mechanical lumbar disc prosthesis replacement,and viscoelastic lumbar disc prosthesis replacement.METHODS:The computerized tomography images of a healthy adult were used to construct a finite element model of the L2-L5 normal lumbar spine with Mimic,Geomagic,and Ansys software.The equipment required for lumbar fusion and lumbar spine replacement was constructed using modeling software,and the L3-L4 segment of the lumbar spine was processed according to the surgical requirements for lumbar fusion and intervertebral disc replacement,creating the corresponding finite element model.Specific boundary conditions were applied to extract the mobility of each lumbar spine segment,the stresses on the neighboring intervertebral discs,and the stresses on the prosthesis lining.RESULTS AND CONCLUSION:(1)Compared with the preoperative period,the maximum stress in the upper neighboring discs increased by 64.09％and 39.79％in the forward flexion and lateral bending states if the original mobility was maintained after lumbar fusion surgery.The maximum stress in the lower neighboring discs increased by 24.39％and 20.98％in forward flexion and lateral bending.This suggested that the upper adjacent discs would suffer greater stress changes than the lower adjacent discs during heavy physical labor.(2)Disc replacement did not show significant changes in adjacent disc stress,with mechanical prosthesis replacement slightly reducing adjacent disc stress,while viscoelastic prosthesis replacement was more in line with the biological properties of the disc,with maximum adjacent disc stress similar to that of the preoperative period.(3)In terms of stability,the mechanical prosthesis replacement segment showed a 51.67％increase in range of motion in the lateral bending state and a 53.27％increase in range of motion in the posterior extension state,whereas the viscoelastic prosthesis was better able to maintain mobility in the replacement segment.(4)In addition,the stresses in the liner of the mechanical prosthesis were mainly concentrated in the edge region,and this stress distribution may lead to edge wear and thus affect the service life of the prosthesis.

BACKGROUND:Lumbar degenerative disease is a disease of the musculoskeletal system that primarily affects the intervertebral structures,and the disease is treated with lumbar fusion and disc replacement.OBJECTIVE:To conduct comparative analysis of the differences between lumbar fusion,mechanical lumbar disc prosthesis replacement,and viscoelastic lumbar disc prosthesis replacement.METHODS:The computerized tomography images of a healthy adult were used to construct a finite element model of the L2-L5 normal lumbar spine with Mimic,Geomagic,and Ansys software.The equipment required for lumbar fusion and lumbar spine replacement was constructed using modeling software,and the L3-L4 segment of the lumbar spine was processed according to the surgical requirements for lumbar fusion and intervertebral disc replacement,creating the corresponding finite element model.Specific boundary conditions were applied to extract the mobility of each lumbar spine segment,the stresses on the neighboring intervertebral discs,and the stresses on the prosthesis lining.RESULTS AND CONCLUSION:(1)Compared with the preoperative period,the maximum stress in the upper neighboring discs increased by 64.09％and 39.79％in the forward flexion and lateral bending states if the original mobility was maintained after lumbar fusion surgery.The maximum stress in the lower neighboring discs increased by 24.39％and 20.98％in forward flexion and lateral bending.This suggested that the upper adjacent discs would suffer greater stress changes than the lower adjacent discs during heavy physical labor.(2)Disc replacement did not show significant changes in adjacent disc stress,with mechanical prosthesis replacement slightly reducing adjacent disc stress,while viscoelastic prosthesis replacement was more in line with the biological properties of the disc,with maximum adjacent disc stress similar to that of the preoperative period.(3)In terms of stability,the mechanical prosthesis replacement segment showed a 51.67％increase in range of motion in the lateral bending state and a 53.27％increase in range of motion in the posterior extension state,whereas the viscoelastic prosthesis was better able to maintain mobility in the replacement segment.(4)In addition,the stresses in the liner of the mechanical prosthesis were mainly concentrated in the edge region,and this stress distribution may lead to edge wear and thus affect the service life of the prosthesis.

Objective To establish an efficient DNA extraction method for the batch identification of genotypes in model mice.Methods We extracted total DNA from transgenic mouse tails using four methods:alkaline simplified group,alkaline routine group,protease K cleavage group and DNA extraction kit group.The purity and concentration of DNA obtained by the four methods were measured,the effects of gel electrophoresis were evaluated,and the time and experimental costs of the four methods were compared.Results The protease K cleavage method produced the highest concentration of DNA,followed by the simplified alkaline boiling and routine alkaline boiling method.The reagent kit produced the highest DNA purity,followed by the simplified alkaline boiling method.The DNA templates obtained by the four method could be amplified by polymerase chain reaction and gel electrophoresis to obtain clear DNA target bands.In addition,the DNA template extracted by the simplified alkaline boiling method could be used for gene identification after storage at-20℃for 1 month,as well as requiring the least time and lowest costs.Conclusions The simplified alkaline boiling method is currently the simplest,fastest,and most economical DNA template-extraction method for batch identification of genotypes in model mice.

Objectives:The study assessed the relationship between atherogenic index of plasma(AIP)and the rapid progression of coronary non-target lesions.Methods:A total of 1 247 patients with coronary artery disease who underwent two coronary angiography examinations at Fuwai Hospital,Chinese Academy of Medical Sciences between January 2010 and September 2014 were enrolled in this retrospective study.The AIP is defined as the base 10 logarithm of the ratio of the concentrations of triglyceride to high-density lipoprotein cholesterol.Patients were divided into the high AIP group(n=623)and the low AIP group(n=624)based on the median value of AIP.Lesion rapid progression is defined as an increase of more than 10%in the lumen stenosis of the lesion with a stenosis rate of more than 50%,or an increase of more than 30%in the lumen stenosis rate of the lesion with a stenosis rate of less than 50%,or a progression to total occlusion within 2 years.Results:Median AIP was 0.39(0.23-0.56)in this patient cohort.Rapid progression of non-target lesions occurred in 65(5.21%),including 42(6.74%)in the high AIP group.The Kaplan-Meier curve showed that the cumulative incidence of rapid progression of non-target lesions was higher in the high AIP group than in the low AIP group(HR=1.751,95%CI:1.053-2.912,log-rank P=0.028).In univariate cox analysis,the AIP and high AIP correlated with rapid progression of non-target lesions.After multivariate adjustment,AIP was an independent risk factor for rapid progression of non-target lesions(adjusted HR=2.731,95%CI:1.090-6.844,P=0.032).Conclusions:AIP is an independent risk factor for rapid progression of non-target lesions.AIP should be considered as a biomarker for estimating the risk of cardiovascular disease,along with other traditional risk factors.

Objective:To investigate the effect of CT-derived fractional flow reserve (CT-FFR) measurement sites on the values and the diagnostic performance, and to determine the optimal measurement site for CT-FFR using invasive FFR as the reference standard.Methods:This study was part of the CT-FFR CHINA clinical trial. Patients with suspected coronary artery disease who were scheduled for invasive coronary angiography (ICA) were prospectively recruited from five clinical centers across the country from November 2018 to March 2020. Each enrolled patient underwent coronary CT angiography (CCTA), CT-FFR, ICA, and invasive pressure wire-based FFR assessments sequentially within one week. Four groups of CT-FFR values were obtained on each enrolled target vessels according to different CT-FFR measurement locations: 1, 2, 3 cm distal to the target lesion, and terminal vessel groups. Spearman and Bland-Altman analyses were used to explore the correlation and consistency of CT-FFR values and FFR values at different measurement sites. The measurement deviation of CT-FFR was also compared. Diagnostic accuracy and performance of CT-FFR, including sensitivity, specificity, positive predictive value, negative predictive value, and area under the receiver operating characteristic curve (AUC), in discriminating myocardial ischemia were analyzed across all measurement site groups on a per-vessel level, using FFR as the reference standard.Results:A total of 289 patients with 345 target lesion vessels were included. According to CCTA, there were 51 target vessels (14.8%) with<50% stenosis, 106 vessels (30.7%) with 50%-69% stenosis, and 188 vessels (54.5%) with stenosis≥70%. At per-vessel level, CT-FFR and FFR values at each measurement position group were highly positively correlated: 1 cm distal to target lesion group, r=0.734 ( P<0.001); 2 cm distal to target lesion group, r=0.732 ( P<0.001); 3 cm distal to target lesion group, r=0.737 ( P<0.001); terminal vessel group was 0.719 ( P<0.001). At per-vessel level, CT-FFR and FFR values of all measurement sites were in good agreement (Bland-Altman analysis results): 1 cm distal to target lesion group, 0.014 (95% LoA 0.002-0.026); 2 cm distal to target lesion group, 0.026 (95% LoA 0.015-0.038); 3 cm distal to target lesion group, 0.040 (95% LoA 0.039-0.051); terminal vessel group, 0.075 (95% LoA 0.064-0.087). And at per-vessel level, the accuracy of diagnosing myocardial ischemia with CT-FFR at 1 cm was highest [84.6% (95% CI 80.4%-88.3%)], and the lowest accuracy in the terminal vessel group [67.0% (95% CI 61.7%-72.0%)]. However, there was no significant difference in the diagnostic accuracy of CT-FFR at 1 cm, 2 cm [80.6% (95% CI 76.1%-84.6%)] and 3 cm [77.5% (95% CI 72.6%-81.7%)]. AUC of CT-FFR at 1 cm distal to the lesion were both highest for global level and moderately stenosis (50%-69%) lesions [0.85 (95% CI 0.81-0.89), 0.84 (95% CI 0.77-0.90)]. And the differences were statistically significant among the four measurement location groups (all P<0.05). Conclusions:The deviation of CT-FFR increases with measurement site distance distal to target lesions. One centimeter distal to the target lesion is the optimal measurement site, and the CT-FFR value here shows the highest diagnostic performance for myocardial ischemic lesions, especially for moderate stenosis.

Objective To observe the value of synthetic MRI(SyMRI)MAGnetic resonance image Compilation(MAGiC)sequence parameters for differentiating cervical squamous cell carcinoma and cervical adenocarcinoma.Methods Sixty-six patients with pathologically confirmed cervical cancer were retrospectively enrolled and divided into cervical squamous cell carcinoma group(n=56)and cervical adenocarcinoma group(n=10).Quantitative MAGiC parameters were collected and compared between groups,and those being significantly different were combined to construct a logistic regression model.The performance of each parameter alone and their combination for differentiating cervical squamous cell carcinoma and cervical adenocarcinoma was evaluated with receiver operating characteristic(ROC)curve and the area under the curve(AUC).Results In cervical adenocarcinoma group,lesions's T1 and T2 were higher,while R1 and R2 were lower than those in cervical squamous cell carcinoma group(all P＜0.05).No statistically significant difference of proton density was found between groups(P＞0.05).The AUC of T1,T2,R1,R2 alone and their combination for differentiating cervical squamous cell carcinoma and cervical adenocarcinoma was 0.959,0.945,0.961,0.942 and 0.996,respectively,and no significant difference was found between each two ones(Z=0.267 to 1.396,all P＞0.05).Conclusion SyMRI had high value for differentiating cervical squamous cell carcinoma and cervical adenocarcinoma.

BACKGROUND: The available evidence regarding the benefits of percutaneous coronary intervention (PCI) on patients receiving dialysis with coronary artery disease (CAD) is limited and inconsistent. This study aimed to evaluate the association between PCI and clinical outcomes as compared with medical therapy alone in patients undergoing dialysis with CAD in China. METHODS: This multicenter, retrospective study was conducted in 30 tertiary medical centers across 12 provinces in China from January 2015 to June 2021 to include patients on dialysis with CAD. The primary outcome was major adverse cardiovascular events (MACE), defined as a composite of cardiovascular death, non-fatal myocardial infarction, and non-fatal stroke. Secondary outcomes included all-cause death, the individual components of MACE, and Bleeding Academic Research Consortium criteria types 2, 3, or 5 bleeding. Multivariable Cox proportional hazard models were used to assess the association between PCI and outcomes. Inverse probability of treatment weighting (IPTW) and propensity score matching (PSM) were performed to account for potential between-group differences. RESULTS: Of the 1146 patients on dialysis with significant CAD, 821 (71.6%) underwent PCI. After a median follow-up of 23.0 months, PCI was associated with a 43.0% significantly lower risk for MACE (33.9% [ n  = 278] vs . 43.7% [ n  = 142]; adjusted hazards ratio 0.57, 95% confidence interval 0.45-0.71), along with a slightly increased risk for bleeding outcomes that did not reach statistical significance (11.1% vs . 8.3%; adjusted hazards ratio 1.31, 95% confidence interval, 0.82-2.11). Furthermore, PCI was associated with a significant reduction in all-cause and cardiovascular mortalities. Subgroup analysis did not modify the association of PCI with patient outcomes. These primary findings were consistent across IPTW, PSM, and competing risk analyses. CONCLUSION This study indicated that PCI in patients on dialysis with CAD was significantly associated with lower MACE and mortality when comparing with those with medical therapy alone, albeit with a slightly increased risk for bleeding events that did not reach statistical significance.
Humans ; Percutaneous Coronary Intervention/methods* ; Male ; Female ; Coronary Artery Disease/drug therapy* ; Retrospective Studies ; Renal Dialysis/methods* ; Middle Aged ; Aged ; China ; Proportional Hazards Models ; Treatment Outcome

Objective To assess the impact of freeze-drying and dry heat virus inactivation processes on the activity ofα2-macroglobulin(A2M)derived from human plasma Cohn fraction Ⅳ.Methods A2M derived from human plasma Cohn fraction Ⅳ was prepared and subjected to programmed freeze-drying with dry heat virus inactivation.The lyophilized products were evaluated for their appearance,water content,and validation of the viral inactivation process.The bioactivity of the products before and after lyophilization as well as before and after dry heat inactivation was determined via trypsin inhibition,and the comparisons were studied.Results The appearance of the lyophilized product was fluffy,and the water content was(5.83±0.45)％.The specific activities of the samples before and after lyophilization were(10.199±0.137)and(10.033±0.201)μg/mg,respectively,with no statistically significantdifference between the two groups(P＞0.05).The viral inactivation of the samples was carried out by using dry heat inactivation conditions at 100 ℃ for 30 min.After inactivation,the reduction was ≥5.125 LgTCID50/0.1 mL in Pseudorabies virus(PRV)titers,≥4.500 LgTCID50/0.1 mL in Sindbis virus(SinV)titers,≥6.375 LgTCID50/0.1 mL in encephalomyocarditis virus(EMCV)titers,and≥4.500 LgTCID50/0.1 mL in porcine parvovirus(PPV)titers.The specific activities of the samples before and after dry heat were(9.921±0.292)and(10.091±0.278)μ g/mg,respectively,with no statistically significant difference between the two groups.Conclusion A2M derived from human plasma Cohn fraction Ⅳ,when subjected to freeze-drying followed by dry heat inactivation at 100 ℃ for 30 minutes,can effectively inactivate viruses without altering the biological activity of the product.

Elemene is widely recognized as an effective anti-cancer compound and is routinely administered in Chinese clinical settings for the management of several solid tumors, including non-small cell lung cancer (NSCLC). However, its detailed molecular mechanism has not been adequately demonstrated. In this research, it was demonstrated that elemene effectively curtailed NSCLC growth in the patient-derived xenograft (PDX) model. Mechanistically, employing high-throughput screening techniques and subsequent biochemical validations such as microscale thermophoresis (MST), microRNA-145-5p (miR-145-5p) was pinpointed as a critical target through which elemene exerts its anti-tumor effects. Interestingly, elemene serves as a binding stabilizer for miR-145-5p, demonstrating a strong binding affinity (dissociation constant (K _D) = 0.39 ± 0.17 μg/mL) and preventing its degradation both in vitro and in vivo, while not interfering with the synthesis of the primary microRNA transcripts (pri-miRNAs) and precursor miRNAs (pre-miRNAs). The stabilization of miR-145-5p by elemene resulted in an increased level of this miRNA, subsequently suppressing NSCLC progression through the miR-145-5p/mitogen-activated protein kinase kinase kinase 3 (MAP3K3)/nuclear factor kappaB (NF-κB) pathway. Our findings provide a new perspective on revealing the interaction patterns between clinical anti-tumor drugs and miRNAs.

Objective To investigate the abnormal changes characteristics of the degree centrality(DC)of the brain functional network in patients with benign paroxysmal positional vertigo(BPPV)in the classical frequency band(0.010-0.080 Hz),the slow-4 frequency band(0.027-0.073 Hz),and the slow-5 frequency band(0.010-0.027 Hz).Methods Twenty patients with BPPV(BPPV group)and 14 healthy controls(HC)(HC group)were selected.Resting-state functional magnetic resonance imaging(rs-fMRI)scans were performed,and the clinical data were analyzed.The DC method was used to analyze the changes of centrality of resting state network in patients with BPPV.Results Compared with the HC group,the BPPV group showed an increase in DC in the left caudate nucleus in the classical frequency band(P＜0.05),and a decrease in DC in the right auxiliary motor region in the classical frequency band(P＜0.05);within the slow-4 frequency band,no significant differences were observed in brain regions(P＞0.05);within the slow-5 frequency band,the BPPV group showed an increase in DC in the left thalamus(P＜0.05),while the left anterior cingulate and paracingulate gyrus showed a decrease in DC(P＜0.05).Conclusion Patients with BPPV have spontaneous activity disorders in multiple brain regions at resting states,and these changes show frequency band specificity.