Effect of slurry proportion on the microstructure and properties of dental lithium disilicate ceramics manufactured through 3D printing.
10.7518/hxkq.2025.2024335
- Author:
Baoxin LIN
1
;
Xiaoxuan CHEN
1
;
Ruyi LI
1
;
Qianbing WAN
1
;
Xibo PEI
1
Author Information
1. State Key Laboratory of Oral Diseases & National Center for Stomatology & National Clinical Research Center for Oral Diseases & Dept. of Prosthodontics, West China Hospital of Stomatology, Sichuan University, Chengdu 610041, China.
- Publication Type:Journal Article
- Keywords:
3D printing;
dental ceramics;
lithium disilicate;
slurry proportion;
stereo lithography apparatus
- MeSH:
Printing, Three-Dimensional;
Dental Porcelain/chemistry*;
Ceramics/chemistry*;
Materials Testing;
Particle Size
- From:
West China Journal of Stomatology
2025;43(2):175-182
- CountryChina
- Language:Chinese
-
Abstract:
OBJECTIVES:This study aims to use 3D prin-ting technology based on the principle of stereo lithography apparatus (SLA) to shape dental lithium disilicate ceramics and study the effects of different slurry proportions on the microstructure and properties of heat-treated samples.
METHODS:The experimental group comprised lithium disilicate ceramics manufactured through SLA 3D printing, and the control group comprised lithium disilicate ceramics (IPS e.max CAD) fabricated through commercial milling. An array of different particle sizes of lithium disilicate ceramic powder materials (nano and micron) was selected for mixing with photocurable acrylate resin. The proportion of experimental raw materials was adjusted to prepare five groups of ceramic slurries for 3D printing (Groups S1-S5) on the basis of rheological properties, stability, and other factors. Printing, debonding, and sintering were conducted on the experimental group with the optimal ratio, followed by measurements of microstructure, crystallographic information, shrinkage, and mechanical properties.
RESULTS:Five groups of lithium disilicate ceramic slurries were prepared, of which two groups with high solid content (75%) (Groups S2 and S3) were selected for 3D printing. X-ray diffraction and scanning electron microscopy results showed that lithium disilicate was the main crystalline phase in Groups S2 and S3, and its microstructure was slender, uniform, and compact. The average grain sizes of Groups S2 and S3 were (559.79±84.58) nm and (388.26±61.49) nm, respectively (P<0.05). Energy spectroscopy revealed that the samples in the two groups contained a high proportion of Si and O elements. After heat treatment, the shrinkage rate of the two groups of ceramic samples was 18.00%-20.71%. Test results revealed no statistical difference in all mechanical properties between Groups S2 and S3 (P>0.05). The flexural strengths of Groups S2 and S3 were (231.79±21.71) MPa and (214.86±46.64) MPa, respectively, which were lower than that of the IPS e.max CAD group (P<0.05). The elasticity modulus of Groups S2 and S3 were (87.40±12.99) GPa and (92.87±19.76) GPa, respectively, which did not significantly differ from that of the IPS e.max CAD group (P>0.05). The Vickers hardness values of Groups S2 and S3 were (6.53±0.19) GPa and (6.25±0.12) GPa, respectively, which were higher than that of the IPS e.max CAD group (P<0.05). The fracture toughness values of Groups S2 and S3 were (1.57±0.28) MPa·m0.5 and (1.38±0.17) MPa·m0.5, respectively, which did not significantly differ from that of the IPS e.max CAD group (P>0.05).
CONCLUSIONS:The combination of lithium disilicate ceramic powders with different particle sizes can yield a slurry with high solid content (75%) and suitable viscosity and stability. The dental lithium disilicate ceramic material is successfully prepared by using 3D printing technology. The 3D-printed samples show a small shrinkage rate after heat treatment. Their microstructure conforms to the crystal phase of lithium disilicate ceramics, and their mechanical properties are close to those of milled lithium disilicate ceramics.
