Effectiveness of three-dimensional printing-assisted vascularized fibular graft for repairing metatarsal defects.
10.7507/1002-1892.202507062
- Author:
Rong ZHOU
1
;
Jihui JU
1
;
Liang YANG
1
;
Liping GUO
1
;
Yucheng LIU
1
;
Chao GENG
1
;
Zhongzheng LIU
1
;
Zefeng NIU
1
;
Shuai DONG
1
Author Information
1. Department of Wound Repair, Suzhou Ruihua Orthopedic Hospital, Suzhou Jiangsu, 215104, P. R.China.
- Publication Type:Journal Article
- Keywords:
Metatarsal defect;
bone repair;
fibular flap transplantation;
three-dimensional printing technique
- MeSH:
Humans;
Printing, Three-Dimensional;
Middle Aged;
Male;
Fibula/blood supply*;
Female;
Metatarsal Bones/injuries*;
Adult;
Bone Transplantation/methods*;
Aged;
Plastic Surgery Procedures/methods*;
Young Adult;
Treatment Outcome
- From:
Chinese Journal of Reparative and Reconstructive Surgery
2025;39(11):1447-1451
- CountryChina
- Language:Chinese
-
Abstract:
OBJECITVE:To investigate the effectiveness of three-dimensional (3D) printing-assisted vascularized fibular graft for repairing metatarsal defects.
METHODS:Between November 2021 and February 2024, 11 patients with varying degrees of metatarsal defects caused by trauma were treated. There were 10 males and 1 female, aged 22-67 years, with a mean age of 51.2 years. The defect locations were as follows: the first metatarsal in 4 cases, the fifth metatarsal in 2 cases, the first and the second metatarsals in 1 case, the first to third metatarsals in 1 case, the third and the fourth metatarsals in 1 case, the third to fifth metatarsals in 1 case, and the first to fifth metatarsals in 1 case. The preoperative American Orthopaedic Foot & Ankle Society (AOFAS) score was 67.0 (48.5, 72.5). Based on 3D-printed bilateral feet models and mirrored healthy-side foot arch angles for preoperative planning and design, the vascularized fibular graft was performed to repair the metatarsal defects. At last follow-up, the medial and lateral longitudinal arches of bilateral feet were measured on weight-bearing X-ray films, and functional assessment was conducted using the AOFAS score.
RESULTS:All operations were successfully completed, with an operation time ranging from 180 to 465 minutes (mean, 246.8 minutes). All incisions healed by first intention, with no occurrence of osteomyelitis. All patients were followed up 6-22 months (mean, 10 months). X-ray film reviews showed bone graft healing in all cases, with a healing time of 3-6 months (mean, 5 months). All patients underwent internal fixator removal at 6-12 months after operation. At last follow-up, no significant difference was observed in the medial and lateral longitudinal arches between the healthy and affected feet ( P>0.05). The AOFAS score of the affected foot was 78.0 (73.5, 84.0), showing a significant improvement compared to the preoperative score ( P<0.05). The effectiveness was rated as excellent in 1 case, good in 7 cases, fair in 2 cases, and poor in 1 case. Linear scarring remained at the donor site, with no functional impairment in adjacent joint movement.
CONCLUSION:3D printing-assisted vascularized fibular graft for repairing metatarsal defects can effectively restore the physiological angle of the foot arch, facilitate the recovery of weight-bearing alignment, promote good bone healing, and yield satisfactory clinical outcomes.
