Background: Relative Dentin Abrasivity (RDA), as set by ISO 11609, is a standardized measurement on the abrasiveness of toothpaste. There are no published RDA values for Philippine-brand toothpastes. This study evaluated the degree of abrasion of five Philippine-brand toothpastes.

Objective: To compare qualitatively and quantitatively the abrasivity of five Philippine-brand toothpastes (Brands X, U, H, HN, G) to two foreign-brand toothpastes Brand C (RDA 68) and Brand P (RDA 150).

Methods: Twenty-four bovine dentin samples were brushed with a slurry of each of the toothpaste using a toothbrushing machine. A profilometer, scanning electron microscope and a visual measuring scope were used to determine abrasivity through the before-and-after-brushing surface roughness.

Results: Ranked based on the difference of the means for surface roughness, before-and-after brushing, in decreasing order of abrasivity are: Brands P, X, U, H, C, HN, and G. Using Dunn's test-post hoc test for Kruskal-Wallis test at p ? 0.05, we showed that the abrasivity of Brands G, H, and HN were not significantly different from Brand C, and Brand X was not significantly different from Brand P. Brand U was significantly less abrasive than Brand P and significantly more abrasive than Brand C.

Conclusion: Brands G, H, and HN can be considered as low-abrasive toothpastes, Brand X a high abrasive toothpaste, and with Brand U was unclear as to category. Findings from qualitative data support the quantitative data.

Dentin ; Toothpastes ; Tooth Abrasion

The aim of this study is to investigate the end of filaments of the different toothbrushes in the market through the stereomicroscope and to evaluate the % of rounded-end filaments considered to be acceptable. 9 brands, total 11 type toothbrushes were tested. 2 toothbrushes of each type which is marked as roundedend filaments were tested. The toothbrushes which are not marked as rounded-end filaments were excluded. The domestic as well as foreign toothbrushes which are familiar to consumers were tested. 2 tufts of each toothbrushes were cut and examined by stereomicroscope using 40x magnification. The procedure was carried out with blind-technique, and the digital photographs were taken. Besides the % of rounded-end filaments, total tufts number, material of the tuft, stiffness, and other special characteristics were recorded. By the classification of Silverstone and Featherstone, rounded-end filaments were examined and counted. The results shows that there are different range of rounded-end filaments according to the toothbrush types(17.7%-91.2%). Atman toothbrush has the most rounded-end filaments(91.2%) among the observed toothbrushes, and the Advantage Plus(Oral-B) has the next(86.75%). E-Clean #411 has the least(17.70%) and E-Clean #410 of the same brand has also low % rounded-end filaments(20.60%). While G.U.M #409(Butler) has 67.90% rounded-end filaments, G.U.M #471 of the same brand has comparative low 41.83% rounded-end filaments. 4 types of total 11 have the rounded-end filaments over 80%, however other 4 types have under even 50%. Considering that the correct brushing habit with a toothbrush which has rounded-end filaments can protect the gingival injury and tooth abrasion, it is thought that we dentists need to give the correct information about toothbrush to the patients
Classification ; Dentists ; Humans ; Tooth Abrasion

This study aims to introduce the method that can relieve vibrating forces to oral environment by making an embouchure aid. Thin plastic crown forms were fabricated to prevent tooth abrasion and irritation to lip mucosa for the saxophone player. After application to the player, the most comfort form was chosen and delivered to 3 professional saxophone players. After 5 mon, the players responded to the survey. This embouchure aid did not disturb playing and gave comfort to lower lip. In general, the players preferred thin soft type and thought it caused little effect on sound. Far too little attention has been paid to the problems encountered by single-reed wind instrumentalist who suffer from tooth abrasion and irritation to lip mucosa. The embouchure aid not only prevent tooth damage but also diminish the discomfort of tight embouchure.
Crowns ; Lip ; Mucous Membrane ; Plastics ; Tooth ; Tooth Abrasion ; Wind

OBJECTIVETo investigate the relationship between wedge-shaped defects and occlusal interference.

METHODSFollowing examination from 46 patients, a total of 157 teeth were identified to have the criteria set for wedge-shaped defects and regarded as the experiment group. Also, 157 adjacent teeth exhibiting no such noncarious cervical lesions were randomly selected from the same group of patients and regarded as the control group. The distribution of occlusal force and time were examined with T-Scan II system in 46 patients with wedge-shaped defects in intercuspal occlusion position, protrusive movement and lateral movement. Occlusal interference and premature contact were evaluated and compared between the two groups.

RESULTSThe proportion of the teeth with premature contact in experiment group was 6.37%, while the control group was 2.55%, there was no significant difference between the two groups (P > 0.05). The total proportion with occlusal interferences in experiment group was 23.57%, which was significantly higher than that of the control group (10.19%, P < 0.05), in experiment group the proportion with working side interferences was 15.92%, and in control group, the proportion was 3.82%, there was significant difference between the two groups (P < 0.01). At the same time, the teeth with occlusal interferences had more serious degree of the wedge-shape defects than those with no occlusal interference.

CONCLUSIONThe increased occlusal force has relation to the formation as well as severity of wedge-shaped defects.

Bicuspid ; Bite Force ; Dental Occlusion ; Humans ; Male ; Tooth Abrasion

OBJECTIVESTo investigate the occlusal characteristics and the condition of tooth abrasion in patients with cracked tooth and to discuss the etiology of the cracked tooth and the relationships between occlusal disorder, tooth abrasion and cracked tooth.

METHODSTwenty-seven patients with cracked tooth were selected. The occlusal courses were recorded by T-ScanIII system in intercuspal position, protrusive movement and lateral movement. Teeth with cracked tooth were regarded as the cracked tooth group, and the healthy adjacent teeth as the control group. The distribution of premature contact, occlusal interference, the center of occlusal force were examined. The abrasive conditions of the two groups were recorded according to the Smith tooth wear index and compared.

RESULTSThere were more teeth with occlusal interference in cracked tooth group (20 teeth) than in the control group (6 teeth), which was significantly different (OR = 5.67, chi(2) = 8.45, P = 0.003). In 24 patients with single affected tooth, the center of occlusal force (COF) located in the inside and outside ellipse were 6 teeth (25%) and 18 teeth (75%) respectively, Z test showed that there were statistical differences between the cracked tooth group and normal people. In cracked tooth group, the proportion of the teeth with abrasion was higher in teeth with occlusal interference than those without occlusal interference (chi(2) = 4.79, P = 0.029).

CONCLUSIONSThe formation of the cracked tooth was related to the occlusal disorder and associated with the tooth abrasion.

Adult ; Dental Occlusion ; Female ; Humans ; Male ; Middle Aged ; Tooth Abrasion ; complications ; Tooth Fractures ; etiology

PURPOSE: The aim of this study was to identify the effects of three aesthetic restorative materials on the wear between tooth and restoration by a pin-on-disk manner. MATERIALS AND METHODS: Six aesthetic restorative materials were used to prepare disk specimens for wear test, which were Lava Zirconia as zirconia group, Vintage MP and Cerabien ZR as veneering porcelain group, Gradia Direct microhybrid composite containing prepolymerized fillers, Filtek Z250 microhybrid composite containing zirconia glass and colloidal silica particles, and Filtek Z350 nanocomposite as composite resin group. Vertical loss of the worn cusp, change of the surface roughness of the restoration materials, and the surface topography were investigated after wear test under 9.8-N contact load. RESULTS: The porcelain groups (Vintage MP and Cerabien ZR) caused the largest vertical loss of teeth when compared with those of the composite resin and zirconia groups, and Filtek Z250 microhybrid composite results in the second-largest vertical loss of teeth. The surface of Filtek Z350 nanocomposite was deeply worn out, but visible wear on the surface of the zirconia and Gradia Direct microhybrid composite was not observed. When the zirconia surface was roughened by sand-blasting, vertical loss of teeth considerably increased when compared with that in the case of fine polished zirconia. CONCLUSION: It was identified that microhybrid composite resin containing a prepolymerized filler and zirconia with reduced surface roughness by polishing were the most desirable restorative materials among the tested materials to prevent the two-body wear between aesthetic restorative material and tooth.
Colloids ; Dental Enamel ; Dental Porcelain ; Glass ; In Vitro Techniques ; Nanocomposites ; Silicon Dioxide ; Tooth ; Tooth Abrasion

OBJECTIVETo clinically investigate and identify the occlusal force as one of factors relative to formation of wedge-shaped defects.

METHODS123 subjects, selected from a group of middle-aged and elderly people in an urban area were divided into four groups: control, light, middle and severe group according to the severity of wedge-shaped defects. Cuspid, first and second premolars, and first molar in maxilla were examined for occlusal force by occlusometer, and the peak value of occlusal contact strain on every maxillary tooth was studied by photocclusion.

RESULTSSignificant reduce of occlusive force in the defected teeth was found than that of in the control teeth. The occlusal contact strain of first premolars with defects by photocclusion was statistically increased. The relative occlusal contact strain of first premolars and first molar of defects was higher than that of their proximate teeth.

CONCLUSIONOcclusal force could have relation to the formation of wedge-shaped defects.

Adult ; Aged ; Bite Force ; Female ; Humans ; Male ; Middle Aged ; Tooth Abrasion ; etiology

OBJECTIVETo study the concentration of stresses at the cervix with simulating restoration of tooth defects.

METHODSA two-dimensional finite element model of a mandible first premolar with defect from longitudinal section was developed. The model was simulatedly restored, respectively by composite resin and glass ionomer cement, and then investigated stress variation in the cervical area.

RESULTSIn the restored models, both of materials improved the concentration of stresses at the cervical area. The composite resin and the glass ionomer cement restorations made the maximum principal stresses declined respectively to 36.2 MPa and 42.5 MPa, which were close to the value of normal tooth in the deepest area of defects.

CONCLUSIONThe concentration of stresses are improved in the cervical area with teeth defects restored.

Composite Resins ; Dental Restoration, Permanent ; Finite Element Analysis ; Glass Ionomer Cements ; Humans ; Tooth Abrasion ; physiopathology ; therapy

OBJECTIVETo perform the quantitative study of tooth occlusal surface wear by a noncontact 3D image survey system.

METHODSThirty-two old people's complete dental casts in five years which had normal occlusion were studied. The same way was used to determine the individual reference surface, and the range of the maxillary first molar occlusal surface was delimited by the unite regulation. Then the quantity of wear in five years and wear rate of maxillary first molar occlusal surface were measured by the noncontact 3D image survey system.

RESULTSWear of maxillary first molar occlusal surfaces was as follows: the mean height loss was 0.293 mm in five years and the mean wear rate was 0.059 mm/year; the mean volume loss was 97.881 mm(3) in five years and the mean wear rate was 19.576 mm(3)/year.

CONCLUSIONSUnder the necessary conditions, the noncontact 3D image survey system is an effective method to measure the wear of dental occlusal surface, but some set-up conditions need to be improved further.

Adult ; Dental Models ; Dental Occlusion ; Female ; Humans ; Imaging, Three-Dimensional ; Male ; Middle Aged ; Tooth Abrasion

To improve the oral health status of Korean people, it is necessary to encourage proper oral hygiene management habits, such as toothbrushing, through appropriate health promotion techniques. Therefore, the purpose of this study was to evaluate the removal of plaque and tooth abrasion using ultra-soft (filament 0.11~0.12 mm) and soft toothbrushes for toothbrushing. The plaque removal was performed using a dentiform and Arti-spray, and the Patient Hygiene Performance (PHP) index was calculated as the sum total score divided by the total number of surfaces. In the abrasivity experiment, according to the number of brushings, a micro Vickers hardness tester was used, and a sample in the range of 280~380 Vickers hardness number was selected. The number of toothbrushing stroke were 1,800 (2 months), 5,400 (6 months), 10,800 (12 months), and 21,600 (24 months). The tooth abrasion was measured using a scanning electron microscope. Statistical analysis was performed using IBM SPSS Statistics 22.0 and a p-value < 0.05 was considered significant. According to the results, there was no statistically significant difference in the degree of plaque removal between ultra-soft and soft toothbrushes. The difference in tooth abrasion between before and after toothbrushing was found to be greater with the soft toothbrushes than with the ultra-soft toothbrushes. Therefore, the ultra-soft toothbrush not only lowers tooth damage by reducing tooth abrasion, but also shows a similar ability to remove plaque as soft toothbrushes.
Dental Plaque ; Hardness ; Hardness Tests ; Health Promotion ; Humans ; Hygiene ; Oral Health ; Oral Hygiene ; Stroke ; Tooth Abrasion* ; Tooth* ; Toothbrushing