This study compared the microleakages and compressive strengths of various base materials.
To evaluate microleakages, 50 extracted permanent premolars were prepared. The teeth divided into 5 groups of 10 each according to the base materials. Cavities with a 5.0 mm width, 3.0 mm length, and 3.0 mm depth were formed on the buccal surfaces of the teeth. After filling the cavities with different base materials, a composite resin was used for final restoration. Each specimen was immersed in 2% methylene blue solution and then observed under a stereoscopic microscope (× 30). To evaluate the compressive strength, 5 cylindrical specimens were prepared for each base material. A universal testing machine was used to measure the compressive strength.
The microleakage was highest in the Riva light cureTM group and lowest in the BiodentineTM and Well-RootTM PT groups. For the compressive strengths, in all groups, acceptable strength values for base materials were found. The highest compressive strength was observed in the Fuji II LCTM group and the lowest strength in the Well-RootTM PT group.

The aim of this study was to evaluate and compare the microstructural properties and mineralization quality of mesiodens with permanent and primary central incisors.Fifteen mesiodens, permanent and primary central incisors were collected. The enamel rod diameter and enamel thickness were observed and measured using field emission scanning electron microscope (FE-SEM). Chemical composition of the enamel was analyzed using energy dispersive X-ray spectrometer (EDS). The measurements were then assessed using the one-way ANOVA and Tukey test.There was no statistically significant difference in the enamel rod diameter between mesiodens and permanent central incisors. However, enamel rods of primary central incisors were smaller than remaining two groups. The thickness of enamel was thick in order of permanent central incisors, mesiodens, primary central incisors. In the composition analysis using EDS, there was no difference in the Ca/P ratio and Ca/C ratio between mesiodens and permanent central incisors, but small in primary central incisors.In conclusion, the microstructural properties of mesiodens were more similar to those of permanent central incisors compared to primary central incisors. Futher, the mineralization quality of mesiodens did not differ significantly from that of permanent central incisors.
Dental Enamel ; Incisor ; Miners

The aim of this study was to compare the degree of conversion and polymerization shrinkage of low and high viscosity bulk-fill giomer-based and resin-based composites. Two bulk-fill giomer (Beautifil Bulk Restorative (BBR), Beautifil Bulk Flowable (BBF)), two bulk-fill (Tetric N-Ceram Bulk-fill (TBF), SureFil SDR flow (SDR)) and two conventional resin composites (Tetric N-Ceram (TN), Tetric N-flow (TF)) were selected for this study. The degree of conversion was measured by using Fourier transform infrared spectroscopy. Polymerization shrinkage was measured with the linometer. For all depth, BBR had the lowest degree of conversion and SDR had the highest. At 4 mm, the degree of conversion of low and high viscosity bulk-fill giomer resin composites was lower than that of bulk-fill resin composites (p < 0.05). At the depth between 2 mm and 4 mm, there were significant difference with TBF, TN and TF (p < 0.05), while no significant difference in the degree of conversion was measured for BBR, BBF and SDR. Polymerization shrinkage of six resin composites decreased in the following order: TF > SDR > BBF > TBF > TN and BBR (p < 0.05). Polymerization shrinkage of bulk-fill giomer resin composites was lower than that of bulk-fill resin composites (p < 0.05). From this study, it is found that the bulk-fill giomer resin composites and TBF were not sufficiently cured in 4 mm depth. The degree of conversion of low and high viscosity bulk-fill giomer resin composites was significantly lower than bulk-fill resin composites in both 2 mm and 4 mm depths. Therefore, such features of bulk-fill giomer resin composites should be carefully considered in clinical application.
Polymerization ; Polymers ; Spectroscopy, Fourier Transform Infrared ; Viscosity