PURPOSE: This study aimed to investigate the potential clinical application of digitized silicone rubber impressions by comparing the accuracy of zirconia 3-unit fixed partial dentures (FPDs) fabricated from 2 types of data (working model and impression) obtained from a laser scanner. MATERIALS AND METHODS: Ten working models and impressions were prepared with epoxy resin and vinyl polysiloxane, respectively. Based on the data obtained from the laser scanner (D-700; 3Shape A/S, Copenhagen, Denmark), a total of 20 zirconia frameworks were prepared using a dental CAD/CAM system (DentalDesigner; 3shape A/S, Copenhagen, Denmark / Ener-mill, Dentaim, Seoul, Korea). The silicone replicas were sectioned into four pieces to evaluate the framework fit. The replicas were imaged using a digital microscope, and the fit of the reference points (P1, P2, P3, P4, P5, P6, and P7) were measured using the program in the device. Measured discrepancies were divided into 5 categories of gaps (MG, CG, AWG, AOTG, OG). Data were analyzed with Student's t-test (alpha=0.05), repeated measures ANOVA and two-way ANOVA (alpha=0.05). RESULTS: The mean gap of the zirconia framework prepared from the working models presented a narrower discrepancy than the frameworks fabricated from the impression bodies. The mean of the total gap in premolars (P=.003) and molars (P=.002) exhibited a statistical difference between two groups. CONCLUSION: The mean gap dimensions of each category showed statistically significant difference. Nonetheless, the digitized impression bodies obtained with a laser scanner were applicable to clinical settings, considering the clinically acceptable marginal fit (120 microm).
Bicuspid ; Denmark ; Denture, Partial, Fixed ; Molar ; Seoul ; Silicone Elastomers ; Siloxanes

OBJECTIVETo compare shear bond strength (SBS) between two types of silicone soft liner and polymethyl methacrylate (PMMA) under the condition of heat curing and room temperature curing.

METHODSA total of 48 PMMA specimens (50 mm x 10 mm x 3 mm) were made by water-bath heating method, and randomly divided into four groups. By using Ufi Gel P (UGP) as soft liner material, group A1 was prepared under heat curing, and group A2 was prepared under room temperature curing. To form the other two groups, Silagum-Comfort (SLC) as soft-liner material was used. Group B1 was prepared under heat curing, and group B2 was prepared under room temperature curing. Shear bond strength (SBS) was tested by using the electronic universal testing machine. The adhesives layer and surface of silastic and PMMA were observed by optical microscope and scanning electron microscopy (SEM).

RESULTSThe SBS of groups A1, A2, B1, B2 were (2.39 +/- 0.24), (1.74 +/- 0.27), (3.09 +/- 0.26), and (2.21 +/- 0.29) MPa, respectively. Significant differences were found between A1 and A2, B1 and B2, A1 and B1, and A2 and B2 (P < 0.05). Optical microscope showed numerous bubbles in the cured UGP, and no air bubbles in the SLC. The surface of PMMA was rough. SEM images showed that each group had continual consistent adhesive interface and a whisker hump on the adhesive layer of A2 and B2.

CONCLUSIONThe SBS ofUGP, SLC, and PMMA achieved minimum clinical standard of 0.44 MPa. The SBS of UGP and PMMA were higher than that of SLC and PMMA. The polymerization method of heat curing was higher than room temperature curing.

Dental Bonding ; Denture Liners ; Dimethylpolysiloxanes ; Materials Testing ; Polymerization ; Polymethyl Methacrylate ; Silicone Elastomers ; Silicones ; Tensile Strength

OBJECTIVETo evaluate the dimensional stability and detail reproduction of five additional silicone impression materials after autoclave sterilization.

METHODSImpressions were made on the ISO 4823 standard mold containing several marking lines, in five kinds of additional silicone. All the impressions were sterilized by high temperature and pressure (135 °C, 212.8 kPa) for 25 min. Linear measurements of pre-sterilization and post-sterilization were made with a measuring microscope. Statistical analysis utilized single-factor analysis with pair-wise comparison of mean values when appropriate. Hypothesis testing was conducted at alpha = 0.05.

RESULTSNo significant difference was found between the pre-sterilization and post-sterilization conditions for all locations, and all the absolute valuse of linear rate of change less than 8%. All the sterilization by the autoclave did not affect the surfuce detail reproduction of the 5 impression materials.

CONCLUSIONSThe dimensional stability and detail reproduction of the five additional silicone impression materials in the study was unaffected by autoclave sterilization.

Dental Impression Materials ; chemistry ; Dental Models ; Hot Temperature ; Materials Testing ; Microscopy ; Polyvinyls ; chemistry ; Silicone Elastomers ; chemistry ; Siloxanes ; chemistry ; Sterilization ; methods

PURPOSE: Vinyl polyether silicone (VPES) has a different composition from other elastomeric impression materials as it combines vinyl polysiloxane (VPS) and polyether (PE). Therefore, it is important to study its properties and behavior under different test conditions. This study investigated the dimensional stability of 5 VPES consistencies when stored for up to 2 weeks, with and without using a standard disinfection procedure. MATERIALS AND METHODS: 40 discs of each VPES consistency (total 200) were made using a stainless steel die and ring as described by ANSI /ADA specification No. 19. 20 discs of each material were immersed in a 2.5% buffered glutaraldehyde solution for 30 minutes. Dimensional stability measurements were calculated immediately after fabrication and repeated on the same discs after 7 and 14 days of storage. The data was analyzed using two-way ANOVA with a significance level set at α = 0.05. RESULTS: The discs mean contraction was below 0.5% at all test times ranging from 0.200 ± 0.014 to 0.325 ± 0.007. Repeated measures ANOVA showed a statistically significant difference after 2-week storage between the disinfected and non-disinfected groups (P < .001). Although there was no statistically significant difference between the materials at the time of fabrication, the contraction of the materials increased with storage for 1 and 2 weeks. CONCLUSION: The dimensional changes of VPES impression discs after disinfection and prolonged storage complied with ANSI/ADA standard. The tested VPES impression materials were dimensionally stable for clinical use after disinfection for 30 minutes in glutaraldehyde and storage for up to 2 weeks.
Disinfection* ; Elastomers ; Glutaral ; Silicon* ; Silicones* ; Siloxanes ; Stainless Steel

A line is drawn from the nasal tip to the most anterior point of the lower lip. The distance from soft tissue pogonion to the ideal soft tissue pogonion is the amount of correction. Alloplastic augmentation does not correct the soft tissue in a 1:1 ratio. In the case of a patient having normal soft tissue(8~11 mm), the ratio of the soft tissue correction is 1:0.66. In the case of a patient having a soft tissue deficiency(less than 7mm), the ratio of the soft tissue correction is 1:0.8. In the case of a patient having a soft tissue excess(more than 12mm), the ratio of the soft tissue correction is 1:0.5. The length of the implant is required to be more lateral to the mental foramen by 1~1.5 cm for restoration of the prejowl sulcus. The posterior surface of the implant must be carved to shape precisely to the bony surface. I usually make several vertical etchings and 20~30 holes in the implant. The vertical etchings help expand the implant to securely fit the mandibular contour. Fenestrated silastic implants can be further stabilized with fibrous tissue ingrowth and future reconstruction if bony erosion occurs.
Chin ; Dimethylpolysiloxanes ; Humans ; Lip ; Silicone Elastomers

PURPOSE: The purpose of this study was to compare the accuracy of the implant master cast according to the type (pick-up, transfer) and the length (long, short) of the impression copings. MATERIALS AND METHODS: The metal master cast was fabricated with three internal connection type implant analogs (Osstem GS III analog), embedded parallel and with 10degrees of mesial angulation to the center analog. Four types of impression coping were prepared with different combinations of types (transfer, pick-up) and lengths (long, short) of the coping. The impressions were made using vinyl polysiloxane (one step, heavy + light body) with an individual tray, and 10 impressions were made for each group. Eventually, 40 experimental casts were produced. Then, the difference in the distance between the master cast and the experimental cast were measured, and the error rate was determined. The analysis of variance was performed using the SPSS (v 12.0) program (alpha = .05), and the statistical significance was set at P < .05. RESULTS: The ANOVA showed that the pick-up type impression coping exhibited a significantly lower error rate than the transfer type. However, no significant difference was observed with respect to the length of the impression coping. Additionally, no significant difference was observed between the parallel and mesial angulated groups. CONCLUSION: Within the limitations of this study, the pick-up type impression coping exhibited a more accurate implant master cast than the transfer type in parallel group. The accuracy of the implant master cast did not differ for different lengths of impression coping of at least 11 mm. Additionally, the accuracy of the implant cast was not different for the parallel and 10degrees mesial angulated groups.
Light ; Polyvinyls ; Siloxanes

Statement of problem: Accurate impression is essential to success of implant prostheses. But there have been few studies about the accuracy of fixture-level impression technique in internal connection implant system. Purpose: This study evaluated the accuracy of splinted fixture-level impression technique using clinical methods and the effect of internal hex on fit of superstructure in internal connection implant system (Astra Tech). Material and method: Two metal master frameworks made from two abutments (Cast-to Abutment ST) each for parallel and divergent conditions and a corresponding, passively fitting, dental stone master cast with four fixture replicas (Fixture Replica ST) were fabricated. Ten dental stone casts were made with vinyl polysiloxane impressions from the master cast by acrylic resin splinted fixture-level impression technique. To evaluate the accuracy of impression technique, the fit of master frameworks for test models was evaluated using screw resistance test (SRT) and onescrew test. The results of SRT were recorded as SRT values from grade 1 to grade 5 by 1/4 turn. And to evaluate the effect of hex on fit of superstructure, the same tests were performed after removing hexes of master frameworks. Results: 1. There was only one case (2.5%) showing SRT value of test model below grade 2 in total before and after removing hexes of master frameworks. And, by removing hexes, SRT values decreased in only one test model (5%) and did not change in 17 test models (85%). 2. SRT values of the 1st screws were grade 2 in 80% of cases before, and grade 1 in 80% of cases after removing hexes. And, by removing hexes, SRT values decreased in 72.5% of cases. 3. SRT values of the 2nd screws were grade 3 in 85% of cases before, and grade 3 in 95% of cases after removing hexes. And, by removing hexes, SRT values did not change in 85% of cases. 4. There were only 2 cases regarded as acceptable fit by one-screw test, and SRT values of 2nd screws of both cases were grade 2. Conclusion: Within the limitations of this study, fixture-level impression of internal connection implant system is considered to obtain inaccurate working cast, even using acrylic resin splinted impression technique. And, it is considered to be unable to improve the fit to remove the hexes of implant restoration.
Prostheses and Implants ; Siloxanes ; Splints

STATEMENT OF PROBLEM: Accurate impression is essential to success of implant prostheses. But there have been few studies about the accuracy of fixture-level impression techniques in internal connection implant systems. PURPOSE: The purpose of this study was to compare the accuracy of two fixture-level impression techniques in two conditions (parallel and divergent) and to assess the effect of tightening sequences and forces on stresses generated on superstructures in internal connection implant system (Astra Tech). MATERIAL AND METHODS: Two metal master frameworks made from two abutments (Cast-to Abutment ST) each and a corresponding, passively fitting, dental stone master cast with four fixture replicas (Fixture Replica ST) were fabricated. Ten dental stone casts for each impression techniques (direct unsplinted and splinted technique) were made with vinyl polysiloxane impressions from the master cast. Strain gauges for each framework were fixed midway between abutments to measure the degree of framework deformation on each stone cast. Pairs of strain gauges placed opposite each other constituted one channel (half Wheatstone bridge) to read deformation in four directions (superior, inferior, anterior, and posterior). Deformation data were analyzed using one-way ANOVA and the Tukey test at the .01 level of significance. And the effect of tightening sequences (right-to-left and left-to-right) and forces (10 Ncm and 20 Ncm) were assessed with ten stone casts made from parallel condition by the splinted technique. Deformation data were analyzed using paired t-test at the .01 level of significance. CONCLUSIONS: Within the limitations of this study, the following conclusions could be drawn. 1. Frameworks bent toward the inferior side on all casts made by both direct unsplinted and splinted impression techniques in both parallel and divergent conditions. 2. There was no statistically significant difference of accuracy between the direct unsplinted and splinted impression techniques in both parallel and divergent conditions (P>.01). 3. There was no statistically significant difference of stress according to screw tightening sequences in casts made by the splinted impression technique in parallel condition (P>.01). 4. Greater tightening force resulted in greater stress in casts made by the splinted impression technique in parallel condition (P<.01).
Prostheses and Implants ; Siloxanes ; Splints*

PURPOSE: This study was performed to measure the accuracy of adjustable dental impression trays by a scanning laser three-dimensional digitizer. MATERIALS AND METHODS: The metal stock, individual, and adjustable stock trays were used for 60 stone casts(10 casts each) duplicated a resin master model of mandible and maxilla. The type IV dental stone was poured in a vinyl polysiloxane impressions and allowed to set for one hour. The master model and the duplicated casts were digitized using an optical digitizer. The distance between the reference points were measured and analyzed on the graphic image of 3-D graphic software(CATIA version 5.0). The statistical significance of the differences between the groups was determined by a two-way ANOVA. RESULTS: There were no significant differences between the accuracies of the adjustable stock tray and the master model except only anterior arch width on the upper arch and the diagonal arch length and arch length on one side of the lower arch. CONCLUSION: The adjustable stock trays showed clinically acceptable accuracies of the study cast produced by them.
Mandible ; Maxilla ; Siloxanes

OBJECTIVETo evaluate the effect of denture base resin surface pretreatment with chemical etchants on microleakage and bond strength between silicone-based resilient liner and denture base resin. The initial bending strength of denture base resin after surface pretreatment was also examined.

METHODSThirty-six polymethyl methacrylate (PMMA) denture base resin blocks (30 mm × 30 mm × 2 mm) were prepared and divided into three groups: group acetone, group methyl methy acrylate (MMA) and group control. Subsequently, a 2 mm silicone-based resilient liner was applied between every two blocks. After 5000 cycles in the thermal cycler (5 and 55°C), they were immersed in the (131) I solution for 24 hours and γ-ray counts were measured. Another 36 PMMA resin blocks (30 mm × 10 mm × 7.5 mm) were prepared. The blocks were divided into three groups and treated as mentioned above. A 3 mm silicone-based resilient liner was applied between every two blocks. After 5000 thermal cycles, tensile bond strength of the sample was measured in a universal testing machine. Another 18 PMMA resin blocks (65 mm × 10 mm × 3.3 mm) were prepared. They were divided into 3 groups and treated in the same way. After an adhesive was applied, the bending strength was measured with three-piont bending test.

RESULTSTwo experimental groups showed lower microleakage (520.0 ± 562.2 and 493.5 ± 447.9) and higher tensile bond strength [(1.5 ± 0.4) and (1.4 ± 0.5) MPa] than the group control [microleakage: (1369.5 ± 590.2); tensile bond strength: (0.9 ± 0.2) MPa, P < 0.05]. There was no statistically significant difference between group acetone and MMA in microleakage and tensile bond strength (P > 0.05). There was no statistically significant difference in bending strength among the three groups (P > 0.05).

CONCLUSIONSTreating the denture base resin surface with acetone and MMA decreased the microleakage, increased the tensile bond strength between the two materials and did not make the initial bending strength of denture base resin decline.

Dental Bonding ; Dental Cements ; Dental Materials ; Denture Bases ; Denture Liners ; Dimethylpolysiloxanes ; Humans ; Materials Testing ; Polymethyl Methacrylate ; Silicone Elastomers ; Silicones ; Surface Properties ; Tensile Strength