This study was to build a canine portal hypertension model by intra-portal administration of high polymer material polyurethane and organic solvent tetrahydrofuran mixed solutions in order to evaluate the effectiveness of the model. Twelve local crossbreed dogs were selected randomly, with intra-portal administration of 8% (weight/volume) polyurethane- tetrahydrofuran solutions through an incision in the upper abdomen to build the portal hypertension model. We measured the portal vein pressure before modeling, during modeling, and four-, eight-, and twelve- weeks after modeling, respectively. Then we evaluated the effectiveness of the model comparing values of data with those data obtained before modeling started, which were regarded as the normal values. The results showed that the portal vein pressure rose by 2. 5 times after the solution administrated instantly as much as that before modeling, and maintained at 1. 5 times after 4 weeks. This method presents an easy operation, low animal mortality and reliable model of portal hypertension. Its less abdominal adhesions and its ability in keeping normal anatomic structure specially make it suit for surgical research of portal hypertension.
Animals ; Disease Models, Animal ; Dogs ; Furans ; adverse effects ; Hypertension, Portal ; Polyurethanes ; adverse effects ; Portal Vein ; physiopathology

Polytetrafluoroethylene (PTFE), polyurethane (PU) and silicone are widely known biocompatible polymers which are commonly used for vascular grafts. However, in vitro and in vivo calcifications of these polymers have been found to seriously compromise their quality as biomaterials. In consideration of this problem, the present study compared the calcification rate and extent of PTFE, PU and silicone. Using the in vitro flow-type method, PTFE, PU and silicone films were tested for 1, 4, 7, 10, 14 and 21 days. After 21 days of in vitro calcification test, the calcium levels on PTFE, PU and silicone were 35.89 5.01 microgram /cm2, 23.73 0.68 microgram/cm2 and 19.86 5.28 microgram/cm2, respectively. The higher observed calcium level for PTFE may be due to the effect of the rough surface of PTFE in accumulating calcium ions on the polymer surface. From the 7th day of test, the [Ca]/[P] molar ratio started to decrease over time, and PTFE showed a faster calcification process. This decreasing [Ca]/[P] molar ratio demonstrated the typical calcification mechanism consisting of phosphorus ion accumulation following calcium ion accumulation. This study concluded that PU and silicone are less calcified than PTFE film, a finding in good agreement with previously published studies.
Biocompatible Materials/*adverse effects ; *Blood Vessel Prosthesis ; Calcinosis/*etiology ; Comparative Study ; Microscopy, Electron, Scanning ; Polytetrafluoroethylene/*adverse effects ; Polyurethanes/*adverse effects ; Silicones/*adverse effects

As the number of patients suffering from cardiovascular diseases and peripheral vascular diseases rises, the constraints of autologous transplantation remain unavoidable. As a result, artificial vascular grafts must be developed. Adhesion of proteins, platelets and bacteria on implants can result in stenosis, thrombus formation, and postoperative infection, which can be fatal for an implantation. Polyurethane, as a commonly used biomaterial, has been modified in various ways to deal with the adhesions of proteins, platelets, and bacteria and to stimulate endothelium adhesion. In this review, we briefly summarize the mechanisms behind adhesions, overview the current strategies of surface modifications of polyurethane biomaterials used in vascular grafts, and highlight the challenges that need to be addressed in future studies, aiming to gain a more profound understanding of how to develop artificial polyurethane vascular grafts with an enhanced implantation success rate and reduced side effect.
Humans ; Polyurethanes ; Biocompatible Materials ; Blood Vessel Prosthesis/adverse effects* ; Cardiovascular Diseases

This article reports a patient with extensive high-pressure injection injury of the hand caused by mistaken injection of polyurethane material into the index finger, who was diagnosed and treated in the Department of Orthopedics of Huzhou Central Hospital in 2019. Both the digital artery and digital nerve were involved, and the polyurethane involved the right palm along the flexor tendon sheath of the index finger and wrist. Due to the lack of X-ray development, the scope of the first debridement was small, and the blood supply to the fingertip was poor. Finally, the patient's right index finger was amputated due to infection and necrosis. MR or B-ultrasound should be perfected before operation to clarify the extent of polyurethane involvement. The initial thorough debridement or multiple debridements are necessary to improve the prognosis. If the blood supply of the fingers is poor, the blood supply can be reconstructed by skin flap transplantation.
Finger Injuries/surgery* ; Humans ; Polyurethanes/adverse effects* ; Plastic Surgery Procedures ; Skin Transplantation ; Surgical Flaps/surgery* ; Treatment Outcome

OBJECTIVETo investigate the feasibility of using new tracheal prosthesis made of biomaterials to replace extensive circumferential tracheal defects in mongrel dogs.

METHODSThree types of tracheal prostheses were developed, whose basic skeleton of tubular mesh was knitted with polypropylene monofilament and poly (lactic-co-glycolic acid) fiber. The inner side of type-I tubular mesh was first coated with polyurethane solution and then with collagen. The exterior of type-I was then immobilized with collagen-hydroxyapatite composites. In contrast, the internal and external walls of type-II were coated with polyurethane solution, which produced a prosthesis similar to a nonporous one, while type-III was coated only with collagen solution. Surgical resection and replacement of a segment of the cervical trachea was performed in 16 adult mongrel dogs. The efficacy of the implanted prosthesis periodically evaluated postoperatively.

RESULTSIn group A, only one died from prosthetic dehiscence, another from anastomotic leakage, and the others had uneventful postoperative courses. The implanted prosthesis was completely incorporated with the recipient trachea, where different length of reepithelialization occurred on the luminal surface of the reconstructed trachea. Macroscopic examination showed scattered and different sizes of neo-ossification surrounding the implanted prosthesis. The prosthesis was roentgenopaque when exposed to routine X rays. In contrast, a relatively high number of complications occurred postoperatively in group B and C.

CONCLUSIONType-I tracheal prosthesis may be used effectively for long-segment circumferential tracheal replacement, and appears very promising for clinical application, with further improvements in promoting the epithelialization.

Animals ; Biocompatible Materials ; Collagen ; Dogs ; Female ; Male ; Polyglycolic Acid ; Polypropylenes ; Polyurethanes ; Prostheses and Implants ; adverse effects ; Prosthesis Design ; Prosthesis Implantation ; Trachea ; surgery