OBJECTIVETo explore the influence factors on determining Tin concentration in air of workplaces with flame atomic absorption spectrometry and to establish an accurate, sensitive and high-efficient method.

METHODSThe different reagents were used to digest the sampling filter membranes and the determining conditions of flame atomic absorption spectrometry were adjusted, then the determining results were compared.

RESULTSWhen 3 ml hydrochloric acid and 0.5 ml nitric acid served as the digesting reagents and the determining conditions of flame atomic absorption spectrometry were adjusted to the best conditions, there was the good linearity in the tested concentration range of Tin, the correlation coefficient was larger than 0.9990. The limit of quantification was 1.0 p.g/ml. The extraction recovery was between 99.6%-102.6%, and the RSD were all less than 5.0%.

CONCLUSIONThe proper kinds and quantity of digestive reagents in pretreatment of the samples should be chosen for the accuracy and precision of the determination according to the influence factors of determination.

Air Pollutants, Occupational ; analysis ; Spectrophotometry, Atomic ; methods ; Tin ; analysis ; Workplace

Objective: To understand the incidence of pneumoconiosis in Ningbo city from 1967 to 2019, and to analyze the distribution characteristics and change trend of pneumoconiosis. Methods: In February 2021, the data of pneumoconiosis patients in Ningbo city from 1967 to 2019 were sorted out. The data from 1967 to 1987 were from historical case files of Zhejiang Center for Disease Control and Prevention, the data from 1988 to 2005 were from the historical case files of Ningbo Center for Disease Control and Prevention, and the data from 2006 to 2019 were from the pneumoconiosis report card in China Disease Prevention and Control Information System; Followed up and supplement relevant information, including basic information, basic information of employers and information related to pneumoconiosis diagnosis, and comprehensively analyze the composition and development trend, population characteristics and industry characteristics of pneumoconiosis. Results: From 1967 to 2019, a total of 1715 cases of pneumoconiosis were reported in Ningbo City, including 1254 cases of stageⅠpneumoconiosis, 258 cases of stageⅡpneumoconiosis, 172 cases of stage Ⅲpneumoconiosis. 1202 cases of silicosis (70.09%) , 296 cases of asbestosis (17.26%) , 40 cases of welder's pneumoconiosis (2.33%) , 32 cases of graphite pneumoconiosis (1.87%) were reported. There were 1296 male cases (75.57%) and 419 female cases (24.43%) were reported. Silicosis (91.15%, 1102/1209) and welder's pneumoconiosis (100.00%, 40/40) were the most common pneumoconiosis in males, while asbestosis (90.24%, 268/297) and graphite pneumoconiosis (87.50%, 28/32) were the most common pneumoconiosis in females. The average age was (49.71±10.90) years old and the average length of service was (10.98±6.96) years. The top three reported pneumoconiosis cases were construction industry (336 cases, 19.59%) , ferrous metal smelting and rolling industry (317 cases, 18.48%) and non-metallic mineral products industry (315 cases, 18.37%) . The top three reported pneumoconiosis cases were 414 cases (24.14%) in Ninghai County, 294 cases (17.14%) in Yuyao City and 272 cases (15.86%) in Yinzhou District. Conclusion: With the development of industries in Ningbo City, government departments should strengthen supervision and management of enterprises involving silica dust and welding fume to curb the high incidence of pneumoconiosis.
Adult ; Asbestosis ; China/epidemiology* ; Female ; Graphite ; Humans ; Incidence ; Male ; Middle Aged ; Pneumoconiosis/epidemiology* ; Pulmonary Fibrosis ; Silicosis/epidemiology*

Objective: To analyze the post distribution of dust concentration in ferrous metal foundry enterprises and evaluate the occupational health risks, and provide basis for policies of the formulation of pneumoconiosis prevention and control. Methods: From August to September in 2020, the basic information, dust hazard information and occupational health management information of 59 ferrous metal casting enterprises were investigated, the dust concentration distribution was analyzed, and the risk assessment was carried out by using the quantitative assignment model. The dust concentration is tested by LSD method after logarithmic treatment. The 3 times time weighted average allowable exposure concentration of dust is taken as the peak concentration limit of dust; The time weighted average allowable exposure concentration of dust converted by exposure time is taken as the time weighted average exposure concentration limit of dust, and whether the time weighted average exposure concentration and peak concentration of dust at the same post exceed the limit is taken as the basis for exceeding the limit of dust post concentration to calculate the post exceeding the limit rate. Results: The dust hazards were mainly distributed in the posts of sand treatment, molding, sand falling, sand cleaning and cutting and grinding. Dust exposure time weighted average concentration was 0.44 (0.03, 5.11) mg/m(3), peak exposure concentration was 1.30 (0.18, 10.94) mg/m(3), and the over standard rate of Posts was 38.92% (79/203) . Weighted average exposure concentration of other dust (total dust) in the cutting and grinding post is 1.50 (0.15, 7.40) mg/m(3), peak exposure concentration is 0.90 (0.07, 12.48) mg/m(3), and the post exceedance rate is 4.88% (2/41) . Weighted average exposure concentration of silica dust (exhaling dust) in dust operation posts of investment casting enterprises is 0.43 (0.05, 6.35) mg/m(3), peak exposure concentration is 0.90 (0.12, 8.28) mg/m(3), and the post over standard rate is 35.77% (49/137) ; Weighted average exposure concentration of other dust (total dust) at the cutting and grinding post is 2.00 (11.00, 21.00) mg/m(3), and the post exceedance rate is 2.50% (2/80) . There was no significant difference in the concentration of respirable dust between sand casting and investment casting (P>0.05) . The concentration of respirable dust in sand casting was higher than that in sand treatment, molding and sand cleaning posts (P<0.05) . The concentration of silica dust in investment casting was higher than that in sand treatment and molding posts, and that in sand cleaning posts was higher than that in sand treatment posts (P<0.05) . 98.48% (454/461) of the dust operation posts have an occupational health risk value greater than or equal to 400, and 1.52% (7/461) of the dust operation posts have an occupational health risk value of 200~399. Conclusion: there is a high rate of exceeding the standard in the dust work posts in the ferrous metal foundry enterprises in Ningbo, and the workers have a high occupational health risk of pneumoconiosis or metal and its compound pneumoconiosis. Targeted measures should be taken to reduce the occupational health risk.
Air Pollutants, Occupational/analysis* ; Dust/analysis* ; Humans ; Occupational Exposure/analysis* ; Pneumoconiosis ; Sand ; Silicon Dioxide/analysis*

Objective: To explore the clinical characteristics and prognosis of the new coronavirus 2019-nCoV patients combined with cardiovascular disease （CVD). Methods: A retrospective analysis was performed on 112 COVID-19 patients with CVD admitted to the western district of Union Hospital in Wuhan, from January 20, 2020 to February 15, 2020. They were divided into critical group (ICU, n=16) and general group (n=96) according to the severity of the disease and patients were followed up to the clinical endpoint. The observation indicators included total blood count, C-reactive protein (CRP), arterial blood gas analysis, myocardial injury markers, coagulation function, liver and kidney function, electrolyte, procalcitonin (PCT), B-type natriuretic peptide (BNP), blood lipid, pulmonary CT and pathogen detection. Results: Compared with the general group, the lymphocyte count (0.74 (0.34, 0.94)×10⁹/L vs. 0.99 (0.71, 1.29)×10⁹/L, P=0.03) was extremely lower in the critical group, CRP (106.98 (81.57, 135.76) mg/L vs. 34.34 (9.55,76.54) mg/L, P<0.001) and PCT (0.20 (0.15,0.48) μg/L vs. 0.11 (0.06,0.20) μg/L, P<0.001) were significantly higher in the critical group. The BMI of the critical group was significantly higher than that of the general group (25.5 (23.0, 27.5) kg/m² vs. 22.0 (20.0, 24.0) kg/m²，P=0.003). Patients were further divided into non-survivor group (17, 15.18%) group and survivor group (95, 84.82%). Among the non-survivors, there were 88.24% (15/17) patients with BMI> 25.0 kg/m², which was significantly higher than that of survivors (18.95% (18/95), P<0.001). Compared with the survived patients, oxygenation index (130 (102, 415) vs. 434 (410, 444), P<0.001) was significantly lower and lactic acid (1.70 (1.30, 3.00) mmol/L vs. 1.20 (1.10, 1.60) mmol/L, P<0.001) was significantly higher in the non-survivors. There was no significant difference in the proportion of ACEI/ARB medication between the critical group and the general group or between non-survivors and survivors （all P>0.05). Conclusion: COVID-19 patients combined with CVD are associated with a higher risk of mortality. Critical patients are characterized with lower lymphocyte counts. Higher BMI are more often seen in critical patients and non-survivor. ACEI/ARB use does not affect the morbidity and mortality of COVID-19 combined with CVD. Aggravating causes of death include fulminant inflammation, lactic acid accumulation and thrombotic events.
Betacoronavirus ; COVID-19 ; Cardiovascular Diseases/therapy* ; Coronavirus Infections/complications* ; Humans ; Pandemics ; Pneumonia, Viral/complications* ; Prognosis ; Retrospective Studies ; SARS-CoV-2 ; Treatment Outcome