No abstract available.
Dentistry ; Endodontics ; Peer Review

No abstract available.
Cone-Beam Computed Tomography ; Dental Pulp Cavity

Oral (p.o.) administration has a delayed onset time of several weeks and moderate efficacy in obsessive-compulsive disorder (OCD), therefore a more rapidly effective treatment is required. The aim of this paper was to review available data detailing the clinical outcome of intravenously (i.v.) administered antiobsessional drug in OCD patients. Review of the research indicates that i.v. administration exhibits a faster onset and greater improvement than p.o. administration. I.v. pulse administration showed clinically significantly faster onset than i.v. gradual administration. I.v. administration was safe and rapidly effective in treatment resistant OCD patients and might be a valuable new treatment.
Administration, Intravenous ; Citalopram ; Clomipramine ; Humans ; Obsessive-Compulsive Disorder

This report describes clinical cases of a palato-gingival groove on a maxillary lateral incisor with associated localized periodontal disease and pulp necrosis. The tooth of the first case was extracted because of severe bone destruction. The palato-gingival groove of the second case was eliminated using a round bur, and the resulting defect was filled with synthetic graft and covered by an absorbable membrane. Both diagnosis and treatment of palato-gingival groove were very difficult and usually extraction of the involved tooth is the treatment of choice, but combined endodontic-periodontic treatment allowed the tooth to be saved.
Dental Pulp Necrosis ; Diagnosis ; Incisor* ; Membranes ; Periodontal Diseases ; Tooth ; Transplants

We report the surgical endodontic treatment of a maxillary first premolar with a lateral lesion that originated from an accessory canal. Although lesions originating from accessory canals frequently heal with simple conventional endodontic therapy, some lesions may need additional and different treatment. In the present case, conventional root canal retreatment led to incomplete healing with the need for further treatment (i.e., surgery). Surgical endodontic management with a fast-setting calcium silicate cement was performed on the accessory canal using a dental operating microscope. At the patient's 9-month recall visit, the lesion was resolved upon radiography.
Bicuspid ; Calcium ; Dental Pulp Cavity ; Radiography ; Retreatment ; Silicate Cement ; Silicates

The purpose of this study is to evaluate the effect of additional enamel etching with phosphoric acid on the microleakage of the adhesion of self-etching primer system. Class V cavity(4 mmx3 mmx1.5 mm) preparations with all margins in enamel were prepared on buccal surface of 42 extracted human upper central incisor teeth. Prepared teeth were randomly divided into 3 groups. Group 1 : no additional pretreatment with 37% phosphoric acid (NE). Group 2 : additional pretreatment with 37% phosphoric acid for 10 seconds (E10s). Group 3 : additional pretreatment with 37% phosphoric acid for 20 seconds (E20s). The adhesives(Clearfil SE Bond(R), Kuraray, Osaka, Japan) and composite resins(Clearfil AP-X(R), Osaka, Kuraray, Japan) were applied following the manufacturer's instructions. All the specimens were finished with the polishing disc(3M dental product, St Paul, MN, USA), thermocycled for 500 cycles between 5degrees C and 55degrees C and resected apical 3-mm root. 0.028 stainless steel wire was inserted apically into the pulp chamber of each tooth and sealed into position with sticky wax. Surrounding tooth surface was covered with a nail varnish 2 times except areas 1 mm far from all the margins. After drying for one day, soaked the samples in the distilled water. Microleakage was assessed by electrochemical method(System 6514, Electrometer(R), Keithley, USA) in the distilled water. In this study, the microleakage was the lowest in group 1(NE) and the highest in group 3(E20s)(NE Dental Enamel* ; Dental Pulp Cavity ; Humans ; Incisor ; Paint ; Stainless Steel ; Tooth ; Water

Mechanical properties and microleakage of two composites [conventional hybrid type DenFil (VERICOM Co., Anyang, Korea) / micro matrix hybrid type Esthet X (Dentsply Caulk, Milford, DE, U.S.A.)] were evaluated to assess whether variable light intensity curing is better than conventional curing technique. Curing was done for 40 seconds in two ways of 2 step soft-start technique and 5 step ramping technique. Three kinds of light intensities of 50, 100, 200 mW/cm2 were initially used for 10, 20, 30 seconds each and the maximum intensity of 600 mW/cm2 was used for the rest of curing time in a soft-start curing technique. In a ramping technique, curing was done with the same initial intensities and the light intensity was increased 5 times with the same rate to the maximum intensity of 600 mW/cm2. After determining conditions that showed no different mechanical properties with conventional technique, Esthet X composite was filled in a class V cavity, which dimension was 4x3x1.5 mm and cured under those conditions. Microleakage was evaluated in two ways of dye penetration and maximum gap estimation through SEM observation. ANOVA and Spearman's rho test were used to confirm any statistical significance among groups. The results were as follows: 1. Several curing conditions of variable light intensities resulted in the similar mechanical properties with a conventional continuous curing technique, except conditions that start curing with an initial light intensity of 50 mW/cm2, 2. Conventional and ramping techniques were better than soft-start technique in mechanical properties of microhardness and compressive strength. 3. Soft-start group that started curing with an initial light intensity of 100 mW/cm2 for 10 seconds showed the least dye penetration. Soft-start group that started curing with an initial light intensity of 200 mW/cm2 for 10 seconds showed the smallest marginal gap, if there was no difference among groups. 4. Soft-start technique resulted in better dye-proof margin than conventional technique (p=0.014) and ramping technique(p=0.002). 5. There was a very low relationship(p=0.157) between the methods of dye penetration and marginal gap determination through SEM evaluation. From the results of this study, it was revealed that ramping technique would be better than conventional technique in mechanical properties, however, soft-start technique might be better than conventional one in microleakage. It was concluded that much endeavor should be made to find out the curing conditions, which have advantages of both aspects or to solve these kinds of problems through a novel idea of polymerization.
Architectural Accessibility ; Compressive Strength ; Gyeonggi-do ; Polymerization ; Polymers