The purpose of this study was to investigate the stress distribution of the abutment and supporting tissues according tot he slopes and types of the guiding plane of distal extension removable partial dentures. The 3-dimensional finite element method was used and the finite element models were prepared as follows. Model I : Kratochvil type guiding plane with 90degree to residual ridge Model II : Kratochvil type guiding plane with 95degree to residual ridge Model III : Kratochvil type guiding plane with 100degree to residual ridge Model IV : Krol type guiding plane with 90degree to residual ridge Distal extension partial denture which right mandibular first and second molar were lost was used and the second premolar was prepared as primary abutment with RPI type retainer. Then 150N of compressive force was applied to central fossae of the first and second molars and von Mises stress and displacement were measured. The results were as follows : 1. Model I and Model IV showed a similar stress distribution pattern and the stress was concentrated on the apex of the root of the abutment. 2. The stress was increased and concentrated on mesial side of the root of the abutment in Model II. The stress was concentrated on buccal and mesiobuccal side of the root of the abutment in Model III. 3. In Model I, the root of the abutment displaced and twisted a little in clockwise. In Model IV, the root of the abutment displaced to distolingually at apical region of the root and mesiobucally at cervical region of the root. 4. In Model II, the root of the abutment displaced to mesiolingually at apical region of the root and more displaced and twisted in counterclockwise at cervical region of the root. In Model III, the root of the abutment displaced to mesiobucally at apical region of the root and more displaced and twisted in clockwise at cervical region of the root.
Bicuspid ; Denture, Partial ; Denture, Partial, Removable* ; Molar

The purpose of this study was to evaluate the effect of dentin pretreatment with Dentin Conditioner,Ultra-Etch,conditioner of Fuji Plus cement on the shear bond strength of resin-reinforced glass ionomer cements to dentin and analyze the fractured surfaces. To evaluate the bond strengh, the extracted human teeth which had uniform area of exposed dentin were cemented with conventional glass ionomer cement. 3M RelyX TM Luting (Vitremer luting cement). Fuji Plus cement after dentin pretreatment. The shear bond strengh was measured using the Universal testing machine(Instron Co., USA) with a crosshead speed of 1mm/m. The effect of dentin pretreatment was evaluated by observing pretreated dentin surfaces under the scanning electron microscope,measuring the shear bond strength and observing the fractured surfaces under the scanning electron microscope. The results were as follows: On the SEM observation of surface morphology, the specimens treated with Dentin Conditioner, Ultra-Etch and conditioner of Fuji Plus cement were removed the smear layer and funneled dentinal tubules in dentin surfaces. In RelyX TM Luting cement group, shear bond strengh of pretreated group was significantly higher than control group. In Fuji Plus cement group and Fuji I group, regardless of the type of pretreatment agents, there was tendency of increase in the shear bond strength. On the SEM observation of fractured surfaces, as the shear bond strength increase, it were shown thicker cement layers and were not shown dentinal tubules. According to these results, it were shown that dentin pretreatment have much effect on bonding states.
Dentin* ; Glass Ionomer Cements* ; Glass* ; Humans ; Smear Layer ; Tooth

According to repeated measurements and correction procedures, the accuracy of the phase-shifting profilometry was developed. At first, after 20 final models for maxillary complete denture were duplicated, the mucosa surfaces of models were measured with the phase-shifting profilometry and each mirror view of these was calibrated. Maxillary cats were divided into 4 groups of 5 casts per each, and wax dentures with 2 sheets of baseplate wax and artificial teeth were made and then cured according to the curing method of each group. Group I ; quick curing with QC-20 acrylic resin Group II ; 9 hour curing with QC-20 acrylic resin Group III ; SR-Ivocap system Group IV ; metal base and quick curing with QC-20 acrylic resin After curing, polishing, and storing at 37degrees C n saline for 30 days, the forms of the impression surface of the dentures were measured with the phase-shifting profilometry. Then, the impression surface form of each denture was placed in the optimal position of comparison with the mirror view of the same final cast. The amount and direction of distortion of each denture was analyzed and the effects of polishing and storage in each denture were compared. The obtained results were as follows : 1. In Group I, the denture was observed as the appearance distorted in the opposite direction of the mucosa and the postero-lateral part of palatal portion of the denture was observed as the appearance separated from the mucosa. Also, the buccal flanges of the denture were observed as the appearance distorted in the direction of the mucosa. 2. In Group II, the postero-lateral part of palatal portion of the denture was observed as the appearance separated slightly from the mucosa. The bilateral buccal flanges of denture were observed as the appearance distorted severely in the direction of the mucosa. 3. In Group III, the bilateral part of the residual ridge crest portions and the buccal flanges of the denture were observed as the appearance distorted in the direction of the mucosa, and specially, the buccal flanges of the maxillary tuberosities were distorted severely. 4. In Group IV, the acrylic resin base of the buccal portion of the denture was observed as the appearance distorted in the opposite direction of the mucosa. 5. The phase-shifting profilometry, done with repeated measurements and correction procedures, was effective in comparing the amount and direction of distortion at every position after the laboratory work and the delivery of maxillary complete denture.
Animals ; Cats ; Denture, Complete ; Dentures* ; Mucous Membrane ; Tooth, Artificial

A modelling scheme for the stress analysis taking into account load transfer characteristics of the osseointegrated interfaces between dental implant and surrounding alveolar bone was investigated. Main aim was to develop a more realistic simulation methodology for the load transfer at the interfaces than the prefect bonding assumption at the interfaces which might end up the reduced level in the stress result. In the present study, characteristics of osseointegrated bone/implant interfaces was modelled with material nonlinearity assumption. Bones at the interface were given different stiffness properties as functions of stresses. Six different models, i.e. tens0, tens20, tens40, tens60, tens80, and tens100 of which the tensile moduli of the bones forming the bone/implant interfaces were specified from 0, 20, 40, 60, 80, and 100 percents, respectively, of the compressive modulus were analysed. Comparisons between each model were made to study the effect of the tensile load carrying abilities, i.e. the effectivity of load transfer, of interfacial bones on the stress distribution. Results of the present study showed significant differences in the bone stresses across the interfaces. The peak stresses, however, were virtually the same regardless of the difference in the effectivity of load transfer, indicating the conventional linear modelling scheme which assumes perfect bonding at the bone/implant interface can be used without causing significant errors in the stress levels.
Dental Implants* ; Lifting ; Linear Models ; Nonlinear Dynamics*

Reticulate acropigmentation of Kitamura, described first by Kitamura and Akam atsu in 1943, is a pigmentary disorder that may be determined by an autasomal dominant gene. Skin lesions are characterized clinically by depressed brownisL pigmented spots, in a reticulated pattern, on the extensor surface of the acral parts of the extremities. Most reported cases are confined to Japanese. We report herein a case of reticulate acropigmentation of Kitarnura in a 28- year-old woman, with a depressed brownish pigmented spots, in a reticulate pattern, on the dorsum of hands and left foot. The authors make the diagnosis of this case a reticulate acropigmentation of Kitamura for the clinical symptoms and histopathologic findings.
Asian Continental Ancestry Group ; Diagnosis ; Extremities ; Female ; Foot ; Genes, Dominant ; Hand ; Humans ; Skin

The effects of pretreatment of Co-Cr alloy, including two adhesive primers that contain either MDP or MAC-10, and silicoating on the bond. The results obtained as follows : Strength of 4-META/MMA-TBB resin were investigated using FT-IR SEM, and EDAX. in the SEM observation of surface morphologies, the sandblasted specimen exibited a very rough surface, whereas the surfaces of the two groups primed with either MDR or MAC-10 were covered with a layer of primer, and the surface morphology of the silicoated specimen remained almost the same after sandblasting. Before the thermocycling tests, the group treated with MDP demonstrated the highest mean tensile bond strength and the sandblasted group showed the lowest bond strength. After 20,000 themocyling, the mean tensile bond strength of the sandblasted group exhibited a 50% reduction in bond strength, while the other showed a 20~30% reduction. Observation of the metal-resin interface revealed that in all groups the resin permeated the rough surface formed by sandblasting thereby producing a mechnical bond between the metal and the resin, It was also found that thermocycling resulted in a gap formation at the metal-resin interface of the specimens, and the sandblasted group exhibited a larger gap width than the other groups. in fracture mode, all specimens indicated a cohesive fracture within the resin before thermocycling. However, thermocyling produced adhesive failure at the edge of the resin-metal interface in most specimens, The sandblasted group, which exhibited the lowest bond strength after thermocycling, also demonstrated the largest area of adhexive failure.
Adhesives ; Alloys*

For the purpose of evaluating the effect of both direct retainer design and bony absorption degree around abutment of indirect retainer on the supporting tissue of abutment of indirect retainer, dislodging force was transmitted to unilateral distal extension RPD bases. Analysis of stress distributed within the supporting tissue around abutment of indirect retainer was carried out. Using three-dimensional photoelastic stress analysis method and the conclusion is a follows. 1. According to the extent of force which the direct retainer of the most distal abutment tooth, the amount of force transmitted to the abutment tooth of indirect retainer was small. 2. Of all the cases, Mandibular first premolar which was used abutment tooth of indirect retainer, buccal, mesial and distal sides represented compression stress and lingual side represented tensile stress. 3. The more bone resorption of abutment tooth of indirect retainer, the more distortion of buccal and distal side of abutment tooth was existed and the extent of compression stress which was existed and distal side to abutment tooth was large. 4. When the alveolar bone around the abutment with indircet retainer is normal. The amount of force transmitted on abutment with indirect retainer was small in the order of Akers clasp, RPA clasp, RPI clasp. 5. When the alveolar bone around the abutment with indirect retainer has been absorbed 20% and 30%, the amount of force transmitted on abutment with indirect retainer was small in the order of RPA calsp, RPI clasp, Akers clasp. 6. When denture is displaced, shape of the direct retainer reciprocating abutment affect much the function of indirect retainer.
Absorption ; Bicuspid ; Bone Resorption* ; Dentures ; Tooth*

This study was designed to compare the smoothness by glazing method with that by polishing method after 48 specimens of Ceramco II block, one of porcelain materials used for PFM, were baked according to the manufacturer's directions. The specimens were roughened with new green stone at 15,000rpm for 30 seconds and sandblasted with 25microliteraluminum oxide for 15 seconds. They were divided into 4 groups at random, and 4 groups were prepared as follows : Group I : specimens were autoglazed and overpolished with polishing system. Group II specimens were polished with only polishing system. Group IIIspecimens were glazed after adding glazing liquid, vitachrom "L"-fluid (vita zahnfabrik co. Germany) to the rough surface Group v : specimens were just autoglazed Using the surface roughness tester, Ra, Rmax, and Rz were estimated 5 times per specimen, and recording process of mean value was repeated 3 times. The results were as follows : 1. The Ra of group I and group IIwas lower than group IIIand group IV (p<001). 2. There was lower value of Rz in group I and group II than group III and group IV (p<001). 3. The Rmax of group I(overpolished with polishing system after autoglazing) and group II(polished with only polishing system) was lower than group III(glazed after adding glazing liquid) and group IV (autoglazed) (p<001). 4. There was not a statistically significant difference between group I and II and between group III and IV (p>001). 5. The roughness was increase in order of group I,II,III,IV in SEM
Dental Porcelain*

BACKGROUND: Surgical correction of the full spectrum of esophageal atresia with tracheoesophageal fistula has improved over the years, but the mortality and morbidity assoiated with repair of these anomalies still remains high. MATERIAL AND METHOD: We retrospectively analyzes 27 surgically treated patients with esophageal atresia and tracheoesophageal fistula at Dong-A University Hospital between January 1992 and March 1997. RESULT: There were 21 male and 6 female patients. Mean birth weight was 2.62+/-.385 kg(2.0~3.4 kg). Twenty- four(88.9%) had esophageal atresia with distal tracheoesophageal fistula, and 3(11.1%) had pure esophageal atresia. Four(14.8%) infants were allocated to Waterston risk group A, 18(66.7%) to group B, and 5(18.5%) to group C. In eighteen(66.7%) infants with associated anomalies, cardiovascular anomalies were the most common. Three had a gap length of 3.5 cm or greater(ultra-long gap) between esophageal segments, 7 had 2.0 to 3.5 cm(long gap), 8 had 1.0 to 2.0 cm(medium gap), and 9 had 1 cm or less(short gap) gap length. Among 27 neonates, 3 cases underwent staged operation, late colon interposition was done in 2, and all other 24 cases underwent primary esophageal anastomosis. Oerative mortality was 2/27(7.4%). Causes of death included acute renal failure(n=1), empyema from anastomotic leak(n=1), necrotizing enterocolitis(n=1), sepsis(n=1), insulin-dependent diabetus mellitus(n=1 . There were 4 anastomosis- related complications including stricture in 3, leakage in 1. Mortality was related to the gap length(p<.05). CONCLUSION: Although the complication rate associated with surgical repair of these anomalies is high, this does not always implicate the operative mortality. The overall survival can be improved by effective treatment for combined anomalies and intensive postoperatve care.
Birth Weight ; Cause of Death ; Colon ; Constriction, Pathologic ; Empyema ; Esophageal Atresia* ; Female ; Humans ; Infant ; Infant, Newborn ; Male ; Mortality ; Retrospective Studies ; Tracheoesophageal Fistula

STATEMENT OF PROBLEM: Standard type of ITI solid implant model in the 6.2mm thick jaw bone was axisymmetrically modelled for finite element stress analyses. PURPOSE: Primary objective was to investigate the influences of the characteristic design configuration of the ITI solid implant model on the bone stress with the course of osseointegration process at the bone/implant interfaces. To simulate the characteristics of the osseointegration process, five different stages of the bone/implant interface model were implemented. As load conditions, vertical load of 50N was taken into consideration. Bone at the cervical region of implant was the areas of concern where the higher level of stress were likely to take place. RESULTS: The results indicated that rather slightly different stress level could be obtained as a function of the osseointegration conditions. CONCLUSION: Under vertical load, the lower level of stress was observed at the cervical cortical bone in the initial and final stages of osseointegration. Relatively higher stress level, however, was observed during the transitional stages where the osseointegration at the cancellous bone interface were yet to fully develop.
Jaw ; Osseointegration*