This article summarizes the common problems in registration and supervision testing of infrared therapy equipment, combines YY 0306-2008 Particular requirements for the safety of heat radiation therapy equipment, GB 9706.1-2007 Medical electrical equipment-Part 1:General requirements for safety, Registration technical review guidelines for infrared treatment equipment, etc. This paper analyzes and discusses the following aspects, including classification and applicable standards, performance indicators and overtemperature protection. Some suggestions and solutions are given to provide some guidance for medical equipment manufacturers in design, research and development and registration, in order to avoid the problem effectively and improve the passing rate of testing.
Electricity ; Equipment Design ; Equipment Safety ; Infrared Rays

This study discusses the effects of infrared thermography in dentistry. Infrared thermography allows the quantification of infrared rays and provides useful data for dental care and research. It has been used for the diagnosis of temporomandibular dysfunction (TMD) and proposed as an objective measure of myofascial pain. It is closely related to temperature and produces beneficial objective data. A study of the heat emissions from facial structures has the potential to benefit dental diagnosis of TMD, postoperative inferior alveolar damage, and endodontic and conservative treatments. In this paper, we assessed infrared thermography in dentistry and consider future developments of infrared thermography.
Dental Care ; Dentistry* ; Diagnosis ; Hot Temperature ; Infrared Rays ; Thermography*

According to the development of body temperature measurement mode, an ear thermometer with infrared thermopiles sensor is designed for body thermometry Compared with oral thermometer, the accuracy of ear thermometer is acceptable.
Body Temperature ; Ear ; Equipment Design ; Humans ; Infrared Rays ; Thermometers

The technical structure of a low-cost thermal imaging system (TIM) lunched on a mobile phone was investigated, which consists of a thermal infrared module and mobile phone and application software. The designing strategies and technical factors toward realizing various TIM array performances are interpreted, including sensor cost and Noise Equivalent Temperature Difference (NETD). In the software algorithm, a mechanism for scene-change detection was implemented to optimize the efficiency of non-uniformity correction (NUC). The performance experiments and analysis indicate that the NETD of the system can be smaller than 150 mK when the integration time is larger than 16 frames. Furthermore, a practical application for human temperature monitoring during physical exercise is proposed and interpreted. The measurement results support the feasibility and facility of the system in the medical application.
Algorithms ; Body Temperature ; Cell Phone ; Humans ; Infrared Rays ; Mobile Applications

Based on the literature review and theories of biophysical theory, the pathway and mechanism of the heat of sandwiched moxibustion stimulating acupoints are analyzed. It is concluded that the heat of sandwiched moxibustion is transferred to the skin of acupoints by heat conduction and thermal radiation. The heat conduct from the skin to deep tissues and other parts was carried out through the biological heat conduction systems. The investigation combined with theories of biological heat conduction was benefit to the research on clinical mechanisms of indirect moxibustion. In addition to heat effect, the infrared resonance of indirect moxibustion and acupoints may be the base of clinical effects of indirect moxibustion.
Body Temperature ; Hot Temperature ; Humans ; Infrared Rays ; Moxibustion ; methods

At present, current stimulation, ultra-sound, and light therapy have become effective methods to promote wound healing. Among them, infrared light is the most widely used method and is one of the important methods to promote wound healing. The therapeutic effect of infrared light on wounds is related to the effect of photobiomodulation on cells and molecules on the skin surface, but the mechanism by which photobiomodulation of infrared light promotes wound healing has not been fully elucidated. Therefore, it is necessary to study the action characteristics and the mechanism of photo-biomodulation of infrared light in promoting wound healing. This article reviews the effect of different types of infrared light on wound healing and the mechanism of infrared light in promoting wound healing.
Infrared Rays ; Low-Level Light Therapy/methods* ; Wound Healing/physiology*

In order to research the infrared radiation characteristics of the skin covering Traditional Chinese acupuncture points, which are NeiGuan in the forearm and LaoGong in the center of the palm, we detected continuously the infrared radiation spectra of the human body surface by using Fourier Transform Infrared Spectroscopy. The experimental results showed that firstly, the differences of the infrared radiation spectra of the human body surface were obvious between individuals. Secondly, the infrared radiation intensity of the human body surface changed with time changing. The infrared radiation intensity in two special wavelength ranges (wavelengths from 6. 79 microm to 6. 85 microm and from 13. 6 microm to 14. 0 microm) changed much more than that in other ranges obviously. Thirdly, the proportions of the infrared radiation spectra changed, which were calculated from the spectra of two different aupuncture points, were same in these two special wavelength ranges, but their magnitude changes were different. These results suggested that the infrared radiation of acupuncture points have the same biological basis, and the mechanism of the infrared radiation in these two special wavelength ranges is different from other tissue heat radiation.
Acupuncture Points ; Adult ; Female ; Humans ; Infrared Rays ; Male ; Skin ; radiation effects ; Spectroscopy, Fourier Transform Infrared

The health-promoting qualities of ultraviolet light have been well recognized, but it also induces deleterious effects from sunburn to skin cancer, Since our enviroment exposes us to both ultraviolet and infrared rays at the same time, the latter is considered to influence to some extent the cutaneous effects of the former. In recent years, it has become increasingly apparent that the biologic effects of one type of radiation may be modified by wavelengths of different energies. Interactions of this kind are complex and occasionally result in true synergy or antagonism. Although there are several reports on these interactions, the results are not in accordance. This study was undertaken to investigate the influence of infrared radiation (IR) on ultraviolet radiation (UVR)-induced skin injury, especially minimal erythema dose (MED). Thirty-five healthy medical students participated in this study between May and June, 1983. One side of the back was exposed to IR with UVR while as a control the other side was exposed only to VVR. The results were summarized as follows : 1. In one experiment treated with IR before UVR, the mean MED-S.D. of the treated site was 17 7+5 3 (sec) and that of the control site was 18. 3-+6. 4 (sec)- The increase of the MED was statistically significant. (p<0. 01], paired t-test) Among the fifteen subjects, the MED was increased in 73% (11/15), and the same in 27% (4/15).
Erythema ; Humans ; Infrared Rays ; Skin Neoplasms ; Skin* ; Students, Medical ; Sunburn ; Ultraviolet Rays

PURPOSE: Phototherapy uses the changes caused by the athermal and atraumatic absorption of the photon's energy by the tissue for therapeutic effect. Phototherapy has been proven to be useful in various conditions, for example, in pain attenuation, wound healing and skin rejuvenation. The aim of this research was to evaluate the clinical efficacy of 830 nm LED phototherapy for burn patients. METHODS: We recruited 11 patients who visited this hospital between June and December 2012 with superficial 2nd degree burns to the face for comparative analysis. For phototherapy, we used infrared LED with wavelength of 830 nm. For comparative analysis, we covered one side of the face with sterile aluminum foil and fabric during the treatment. Photographs were taken at the time of each treatment and the time taken for epithelialization and the level of patient satisfaction were also investigated. RESULTS: All 11 patients were male and the mean age was 44.0+/-11.9 years (range of 28~63 years). The cause of the burns was flame burn for 7 patients, and electric sparks in 4 patients. The time taken to achieve epithelialization after the burns was 8.1+/-2.2 days (range 4~12 days) for the side that received phototherapy, while it was 9.1+/-2.9 days (range 4~14 days) for the side that was not treated with phototherapy. In terms of patient satisfaction, 3 patients were 'Very Satisfied', 6 patients were 'Satisfied', 2 patients replied 'Adequate' and none of the patients were 'Unsatisfied'. CONCLUSION: LED phototherapy of 830 nm wavelength can shorten the time taken for burn wound healing. It also was not associated with serious complications except for skin dryness, so it can be a useful treatment method for burns that produces satisfactory outcome for the patients.
Absorption ; Aluminum ; Burns ; Humans ; Infrared Rays ; Lasers, Semiconductor ; Male ; Patient Satisfaction ; Phototherapy ; Rejuvenation ; Skin ; Wound Healing

PURPOSE: The present study was intended to evaluate the effect of soldering techniques with infrared ray and gas torch under different gap distances (0.3 mm and 0.5 mm) on the tensile strength and surface porosity formation in Ni-Cr base metal alloy. MATERIALS AND METHODS: Thirty five dumbbell shaped Ni-Cr alloy specimens were prepared and assigned to 5 groups according to the soldering method and the gap distance. For the soldering methods, gas torch (G group) and infrared ray (IR group) were compared and each group was subdivided by corresponding gap distance (0.3 mm: G3 and IR3, 0.5 mm: G5, IR5). Specimens of the experimental groups were sectioned in the middle with a diamond disk and embedded in solder blocks according to the predetermined distance. As a control group, 7 specimens were prepared without sectioning or soldering. After the soldering procedure, a tensile strength test was performed using universal testing machine at a crosshead speed 1 mm/min. The proportions of porosity on the fractured surface were calculated on the images acquired through the scanning electronic microscope. RESULTS: Every specimen of G3, G5, IR3 and IR5 was fractured on the solder joint area. However, there was no significant difference between the test groups (P > .05). There was a negative correlation between porosity formation and tensile strength in all the specimens in the test groups (P < .05). CONCLUSION: There was no significant difference in ultimate tensile strength of joints and porosity formations between the gas-oxygen torch soldering and infrared ray soldering technique or between the gap distance of 0.3 mm and 0.5 mm.
Alloys ; Collodion ; Diamond ; Electronics ; Electrons ; Infrared Rays ; Joints ; Porosity ; Tensile Strength