This study is to report the influence of conditions in spray drying process on physical and chemical properties and lung inhaling performance of Panax notoginseng Saponins - Tanshinone II A composite particles. According to the physical and chemical properties of the two types of components within the composite particles, three solvent systems were selected including ethanol, ethanol : acetone (9 : 1, v/v) and ethanol : acetone (4 : 1, v/v), and three inlet temperature: 110 degrees C, 120 degrees C, 130 degrees C to prepare seven different composite particle samples; each sample was characterized using laser diffraction, scanning electron microscopy (SEM), dynamic vapour sorption (DVS) and atomic force microscope (AFM), and their aerodynamic behavior was evaluated by a Next Generation Impactor (NGI). The results indicate that under the conditions of using the mixed solvent system of ethanol--acetone volume ratio of 9 : 1, and the inlet temperature of 110 degrees C, the resulting composite particles showed rough surface, with more tanshinone II A distributing in the outer layer, such composite particles have the best lung inhaling performance and the fine particle fraction (FPF) close to 60%. Finally it is concluded that by adjusting the conditions in co-spray drying process, the distribution amount and existence form of tanshinone II A in the outer layer of the particles can be changed so that to enhance lung inhaling performance of the drug composite particles.

AIM: The changes of myocardial nuclear membrane Ca 2+ -ATPase function was investigated in ischemia/reperfusion injury. METHODS: The model of myocardial ischemia/reperfusion injury was established in rats. Myocardial nuclei were purified with sucrose density centrifugation,the activity of Ca 2+ -ATPase was measured and calcium uptake was assayed with [ 45 Ca 2+ ] . RESULTS: Plasma levels of malondialdehyde (MDA) and free fatty acid (FFA) in myocardial ischemia/reperfusion injury increased significantly( P

Objective To evaluate the correlation between high-sensitivity C-reactive protein(hsCRP)and neutrophil alkaline phosphataee(NAP).Methods 74 patients with different hsCRP levels and 20 healthy subjects were selected.hsCRP and NAP were detected in every person,then the t test and correlation analysis were conducted.Results The NAP integral value of high-value hsCRP group and mid-value were significantly higher than the low-value hsCRP group(P ＜ 0.01),and the NAP group average positive rate of the high,median hsCRP values were 81.8％and 82.3％,which were higher than low-value of hsCRP group(53.6％).Compared the correlation between each group of hsCRP value and integral value of NAP,the hsCRP of high-value hsCRP group has a good correlation with NAP integral value(P ＜ 0.01),while the hsCRP of mid-value of hsCRP group and NAP integral is less relevant(P ＞0.05).Conclusion hsCRP as an acute reactive protein exists a good correlation with NAP,when hsCRP ＞ 50mg/L,it can partially replace NAP.

OBJECTIVE: To investigate the feasibility of a drill template for the placement of guided template of middle and upper thoracic percutaneous vertebroplasty in thoracic pedicle approach on digital design and 3D printing technology. METHODS: The preoperative CT images of 20 patients with thoracic fracture were collected retrospectively. With the 3D soft tissue printing technology, the data was reconstructed by 3D imaging reconstruction software to produce 1∶1 three dimensional soft tissue model. The pedicle screw channel and the digital template were designed by the 3-matic module of Mimics15.0 software. After guide template was printed by 3D printer and three dimensional template was fixed on the model, 2.0 mm Kirschner was placed and the accuracy of a drill template was observed by CT scans, bone cement was injected through the puncture tube and verified with images. The time of nail guide design, guide template production and cost were recorded. RESULTS: The effectiveness of three dimensional thoracic model and digital guided template of middle and upper thoracic percutaneous vertebroplasty of thoracic fractures in thoracic pedicle approach was confirmed. Kirschner was placed and the accuracy of screw placement was confirmed with CT scanning. Template and the corresponding anatomical landmark fitted well, bone cement had showed good filling. The average printing time of upper thoracic spine model with soft tissue, the mean time of nail guide design, guide template production and cost were (719.00±3.03) min, (12.30±1.01) min, (55.50±10.30) min and RMB 3 150 yuan on average respectively. CONCLUSION By means of individual design and 3D soft tissue printingtechnology, accurate placement of guided template of middle and upper thoracic percutaneous vertebroplasty could be realized.
Humans ; Pedicle Screws ; Printing, Three-Dimensional ; Retrospective Studies ; Surgery, Computer-Assisted ; Vertebroplasty