The casting removable partial denture (RPD) is one of most commonly prosthesis methods in present. Vitallium is one kind of dental alloy with cobalt, chromium and molybdenum etc. It has three ranks respectively: Vitallium, Vitallium 2000 and Vitallium 2000 plus. Although the traditional casting RPD are commonly used, but it has been limited in the physical capabilities of traditional dental alloy. It would not been done to flexible design on denture especially on denture base. The elasticity of casting clasp is not good, the volume is thick. Because of the Vickers hardness and elongation of Vitallium 2000 and Vitallium 2000 plus are better than traditional dental alloys, so the RPD with Vitallium 2000 has good bending control, deformation rebound and fracture resistance. The benefit of Vitallium 2000 or Vitallium 2000 plus is the RPD with splitting can be designed for some free end clinical cases, to solve some clinical problems.
Chromium ; Chromium Alloys ; Cobalt ; Dental Alloys ; Denture, Partial, Removable ; Elasticity ; Hardness ; Humans ; Vitallium

This study was conducted to evaluate the tensile bond strength by bonding the dental bracket with Super-bond after treating the surface of dental Nickel-Chromium alloy with sandblasting, sandblasting & tin-plating, respectively, and tin-plating. 10 pieces of Nickel-Chromium alloys with brackets bonded with Super-bond without their surface treatment were sampled as a control group, 20 pieces of Nickel-Chromium alloy brackets bonded with Super-bond after treating them with sandblasting as group I, 20 pieces of Nickel-Chromium alloys tin-plated and bonded with Super-bond after sandblasting as group II, and then 20 pieces of alloys with brackets bonded with Super-bond after tin-plating as group III. The result of those examination and comparison is summarized as follows: 1. Group I showed the mean tensile bond strength of 14.41+/-2.24MPa which was highest among 4 groups, followed by group III( 13.59+/-L51MPa ), group II( 12.27+/-1.45MPa ), and control group( 10.50+/-1.57MPa ), respectively. However, it was shown that them was no statistically significant difference between group I and III, group III and II, and group II and control group( P>005 ). 2. The main failure pattern of those brackets showed that 70% of the control group had an adhesive failure at the bracket Superbond interface, and 30% at the Nickel-Chromium alloy-Superbond interface, while other groups did the adhesive failure at the bracket-Superbond interface. 3. When examined under SEM, it was shown that adhesives were mostly attached to the surface of the Nickel-Chromium alloy for all groups while a considerable quantity of adhesives were attached to the bracket base. Then, those samples treated only with sandblasting showed the most even and remarkable roughness of their surface.
Adhesives ; Alloys* ; Chromium Alloys

OBJECTIVETo investigate the effect of the laser surface hardening technology on the corrosion resistance of dental casting alloy.

METHODSTwenty-three cobalt-chromium alloy specimens were made in this study. Twenty-two specimens were equally divided into two groups randomly. One was experimental group for laser surface hardening processing and the other was control group without any treatment. In each group, ten specimens were used for corrosion analysis by electrochemical method, and one for surface metallographical structure and morphology observation by scanning electron microscope. Remaining one specimen was partially processed on limited area for surface metallographical structure and morphology comparison.

RESULTSMetal grains distributed uniformly and achieved a good refinement with mainly the same size in experimental group. Metal grains in specimen which processed in its partial surface area also achieved a good refinement in the laser processing area. There was statistical difference in electric potential of corrosion and logarithmic value of current of corrosion between experimental group and control group (P < 0.01).

CONCLUSIONLaser surface hardening technology has a positive effect in improving the corrosion resistance of dental casting alloy in artificial saliva.

OBJECTIVEThe aim of this study was to investigate the korrosionsneigung of three metal specimens for casing removable denture by means of electrochemical method.

METHODSThree kinds of test specimens were prepared, including cobalt-chromium alloy, nickel-chrome alloy with titanium and pure titanium. Then they were analyzed via linear polarization in artificial saliva simulating oral environment. From this electrochemical test the polarization curves of these kinds of specimens were recorded. Then the scanning electron microscope (SEM) and X-ray diffractometer (XRD) were applied to assess the morphology and phase changes before and after electrochemical corrosion.

RESULTSNo typical Tafel curve had been recorded for pure titanium, other than cobalt-chromium alloy and nickel-chrome alloy with titanium. Nickel-chrome alloy with titanium got more negative corrosion potential and higher corrosion current than cobalt-chromium alloy. Via SEM, the obvious changes were observed on the morphology and phase before and after corrosion on cobalt-chromium and nickel-chrome alloy with titanium specimens while pure titanium having no change. The XRD provided us little changes on these all three materials.

CONCLUSIONThe results confirm that the korrosionsneigung of the studied cobalt-chromium alloy in artificial saliva is lower than that nickel-chrome alloy with titanium. Pure titanium is the most stable one of the three materials and is extreme hard to be etched.

PURPOSE: The purpose of this study was to evaluate the level of electro-chemical corrosion and surface roughness change for the cases of Ti abutment connected to restoration made of base metal alloys. MATERIALS AND METHODS: It was hypothesized that Ni-Cr alloys in different compositions possess different corrosion resistances, and thus the specimens (13x13x1.5 mm) in this study were fabricated with 3 different types of metal alloys, commonly used for metal ceramic restorations. The electrochemical characteristics were evaluated with potentiostat (Parstat 2273A) and the level of surface roughness change was observed with surface roughness tester. Paired t-test was used to compare mean average surface roughness (Ra) changes of each specimen group. RESULTS: All specimens made of nickel-chromium based alloys, average surface roughness was increased significantly (P < .05). Among them, the Ni-Cr-Be alloy (0.016 +/- 0.007 microm) had the largest change of roughness followed by Ni-Cr (0.012 +/- 0.003 microm) and Ni-Cr-Ti (0.012 +/- 0.002 microm) alloy. There was no significant changes in surface roughness between each metal alloys after corrosion. CONCLUSION: In the case of galvanic couples of Ti in contact with all specimens made of nickel-chromium based alloys, average surface roughness was increased.
Alloys ; Chromium Alloys ; Corrosion ; Family Characteristics ; Metal Ceramic Alloys ; Titanium

OBJECTIVEThe aim of the study was to detect the expression of Ki67 and P53 proteins in the gingival tissue before and after wearing three kinds of dental casting alloy crowns.

METHODSThe three kinds of dental casting alloys (58% golden alloy, NiCr alloy, NiCr alloy excluding Be) were used to make full crowns for 3 dogs in each group. Another 3 dogs were taken as control. The immunohistochemistry Envision method was used to measure the expression of Ki67 and P53 proteins in the gingival tissue before wearing the crowns, 2 weeks, 1 month, 2 months, 3 months after wearing the crowns.

RESULTSThe expression of Ki67 and P53 proteins in gingival tissue increased 1 month after wearing NiCr alloy and NiCr alloy excluding Be, then decreased gradually. And the expression of Ki67 and P53 proteins in 58% golden alloy group was similar to that in control. No pathological change was observed in all samples.

CONCLUSIONTwo kinds of NiCr alloy crowns both can increase the expression of Ki67 and P53 proteins in gingival tissue, but 58% golden alloy crowns can not. So compared with NiCr alloy crowns, 58% golden alloy crowns have better biological properties. And none of three kinds of dental alloy crowns may induce long-term abnormal proliferation in gingival tissue.

OBJECTIVEThe purpose of the study was to investigate the content of nickel (Ni) ion in patients' saliva after wearing the porcelain-fused-to nickel-chromium (Ni-Cr) crown or the porcelain-fused-to nickel-chromium-titanium(Ni-Cr-Ti) crown.

METHODS50 patients who had one molar or premolar needed repairing were selected and divided into two groups randomly. Patients in one group were fabricated with porcelain-fused-to Ni-Cr crown and the patients in the other group were fabricated with porcelain-fused-to Ni-Cr-Ti crown. Collect the patients' saliva before wearing, 1 week, 3 months, and 6 months after wearing. The content of Ni ion in saliva was detected by inductively coupled plasma mass spectrometry (ICP-MS).

RESULTSThe content of Ni ion in both groups increased at the first week, and go back after 6 months. There were no significant differences before wearing, 1 week, 3 months, and 6 months after wearing. There were no significant differences between the two groups.

CONCLUSIONWearing the porcelain-fused-to Ni-Cr crown or the porcelain-fused-to Ni-Cr-Ti crown has no significant influence on the content of Ni ion in saliva.

OBJECTIVETo analyze the final color of Solidex in six thickness interacting with three different backgrounds.

METHODSFive specimens of Solidex in each shade A1, A3, and C2 were fabricated at thickness of 1.0, 1.2, 1.4, 1.6, 1.8, and 2.0 mm. The CIE L(*)a(*)b(*) values of specimens were measured using a colorimeter (ShadeEye NCC) to determine the colorimetric difference, when the specimens overlaid on different backgrounds.

RESULTSWhen the thickness was more than 1.8 mm, the color difference (DeltaE(*)ab < 1) was not perceived by human observers. When the thickness was 1.4 mm or less than 1.4 mm, the color difference (DeltaE(*)ab > 2.72) was considered clinically unacceptable between alloy background and two types of composite resin background.

CONCLUSIONSAlloy background had more evident influence on the final color of Solidex than composite resin background. When making metal-free crown restoration using Solidex, it was advisable to make the composite resin more than 1.8 mm thick.

OBJECTIVES: At present, removable partial denture is still one of the main restoration methods for dentition defects. However, the trend for digital partial denture is becoming more and more obvious in the field of oral repair. However, there are relatively few studies on digital removable partial denture. The aim of this study is to investigate the effects of 3 processing technologies (precision casting, digital cutting, and 3D printing) on the fitness for the clasps of cobalt chromium alloy and pure titanium removable partial denture, and to provide a theoretical basis for the clinical application of digital removable partial denture. METHODS: Clasps of Co-Cr alloy and pure titanium were produced by 3 different processing technologies (precision casting, digital cutting, and 3D printing). There are 6 groups, including a casting pure titanium group, a casting cobalt chromium group, a cutting pure titanium group, a cutting cobalt chromium group, a printing pure titanium group, and a printing cobalt chromium group ( RESULTS: There was no statistical difference in fitness between the casting pure titanium group and the casting cobalt chromium group ( CONCLUSIONS The cobalt chromium alloy and pure titanium clasps made by precision casting, digital cutting, and 3D printing have good fitness. Under the same process, there is no significant difference between cobalt chromium alloy and pure titanium clasps. The 3D printing pure titanium clasps have better fitness than casting pure titanium and cutting pure titanium clasps, which meet the needs of clinical application.
Chromium Alloys ; Cobalt ; Denture, Partial, Removable ; Titanium

OBJECTIVETo investigate the effects of the leaching liquids of 4 differents kinds of dental alloys (Au alloy, Ag-Pd alloy, Co-Cr alloy, Ni-Cr alloy) on apoptosis related gene and protein of fibroblast L929.

METHODSThe L929 cells of mouse were treated in vitro with leaching liquids of 4 different kinds of dental alloys, Au alloy (group A), Ag-Pd alloy(group B), Co-Cr alloy(group C) and Ni-Cr alloy(group D). The RPMI1640 cell medium containing 10% fetal calf serum was served as a control(group E). The effects of these alloys on the expression of caspase-3, 8, 9 of L929 cells were examined by reverse transcription-polymerase chain reaction (RT-PCR) and immunohistochemistry method. Results After 48 h culture, the mRNA levels of caspase-3 and caspase-9 demonstrated significant differences between the groups expect group A and group E. The mRNA levels of caspase-8 had no change in all groups. The expression of caspase-3 and caspase-9 were significant differences between the groups expect group A and C, group B and D. The expression of caspase-8 had no change in all grotps.

CONCLUSIONThe leaching liquids of 4 different kinds of dental alloys expect Au alloy may induce cell appotosis through mitochondrion pathway.