Objective To optimize ultrasonic-assisted extraction Epimedin C and Icariin from Epimedii Wushanensis Herba by response surface methodology. Methods On the basis of single factor tests, Box-Behnken experimental design and response surface methodology were adopted to optimize extraction conditions with the concentration of ethanol, ultrasonic time and solid-liquid ratio as factors. HPLC was used to determine the content of Epimedin C and Icariin from Epimedii Wushanensis Herba. Results Optimal ultrasound-assisted extraction technology was as following: the concentration of ethanol was 73%; the ultrasonic time was 22 min; the ratio of liquid to material was 1:32. The contents of Epimedin C and Icariin from Epimedii Wushanensis Herba were 15.90% and 0.75%, respectively. Conclusion This extraction technology can improve the extraction efficiency of Epimedin C and Icariin from Epimedii Wushanensis Herba, which is in accordance with predicted value.

Objective To study the impact on the radiation dose,organ doses of eye lens and thyroid and image quality with different scanning modes in head and neck CT scan.Methods The simulation phantom of head and neck was scanned by using fixed scanning condition (120 kV and 200 mAs),as well as the combinations of automatic tube current modulation (CARE Dose 4D),automatic tube voltage modulation technique (CARE kV) and partial angle scanning mode (X-CARE) respectively.Six kinds of scanning modes were adopted,including 120 kV +200 mAs,120 kV + 200 mAs + X-CARE,CARE Dose 4D + 120 kV,CARE Dose 4D + 120 kV + X-CARE,CARE Dose 4D + CARE kV,CARE Dose 4D + CARE kV + X-CARE.Two thermolumineseece dosimeters (TLDs) were exposed at the skin surface positions of eye lens and thyroid,and the values measured with two TLDs were averaged.The CT dose index volume (CTDIvol) and dose length product (DLP) for every scan were recorded,and the contrast to noise ratio (CNR) in eye lens section and thyroid section were measured.Results The crgan doses of lens and thyroid were 19.8 and 26 mGy at 120 kV and 200 mAs,as well as 13.3 and 22.2 mGv at X-CARE mode.Compared with the manual selection of 120 kV,the combination of CARE kV and CARE Dose 4D made the values of CTDIvol drop from 13.1 to 10.1 mGy,the doses of eye lens and thyroid from 16.6 and 20.8 mGy to 23.7 and 19.9 mGy respectively,while the image quality reducedsignificantly.Compared with CARE Dose 4D + 120 kV,the organ doses of eye lens and thyroid were reduced from 20.8 and 23.7 mGy to 9.6 and 15.1 mGy for with additional X-CARE,while CTDIvol dropped from 13.1 to 9.3 mGy.When the combination of CARE Dose 4D + CARE kV + X-CARE was used,CTDIvol and organ doses were reduced to a minimum,when the CNRs of head and neck were also minimized.Conclusions The scanning mode CARE Dose 4D + 120 kV + X-CARE for head and CARE Dose 4D + CARE kV for neck can effectively reduce the radiation dose while keeping good image quality.When requirements for image quality are not high,CARE Dose 4D + CARE kV + X-CARE mode can be selected to reduce the radiation dose significantly.

Objective To compare the effects of movable artificial lumbar vertebra implantation and traditional vertebral excision and fusion on the stress of adjacent intervertebral discs,so as to provide reference for the biomechanical safety of new prosthesis implantation.Methods The total lumbar vertebra CT scan data of a healthy adult were imported into the compute r-aided software Mimics 16.0 for three dimensional reconstruction.The reconstructed three dimensional model was smoothed using computer-aided software Geomagic Studio 12.0.Subsequently,meshing,parameter setting and ligaments reconstructing were completed using computer-aided software Hypermesh 13.0 and Solidworks 2013,successfully constructing the finite element model of lumbar vertebral physiology group.On the basis of the finite element model of physiological group,three vertebral bodies and two intervertebral spaces were fused and fixed,and a simplified finite element model of fusion group was constructed.The partitioned prosthesis model was inserted into the established finite element model of physiological group,replacing the L 3 vertebral body and the adjacent two intervertebral discs in the model,constructing the finite element model of non fusion group.Three finite element models were imported into computer-aided software Abaqus/Explict and loaded under six motion modes including anteflexion,dorsiflexion,left and right rotation,and left and right bending.The stress changes of adjacent intervertebral discs were calculated.Results The maximum Mises stress of the adjacent intervertebral disc in the direction of forward flexure,dorsal extension,left and right rotation and left and right lateral bending of the three finite element models was located at the site of loading and increased with the increase of loading.Under the maximum loading,the Mises stress of adjacent intervertebral discs in the above directions in the fusion group (L1-2 respectively were 0.79,0.96,1.26,1.92,1.34,1.57 MPa while L4-5 respectively were 0.52,1.13,1.50,1.74,0.94,0.87 MPa) was significantly higher than that in the physiological group (L1-2 respectively were 0.42,0.53,0.57,0.66,0.64,0.72 MPa while L4-5 respectively were 0.23,0.29,0.68,0.63,0.37,0.34 MPa).The Mises stress of adjacent intervertebral disc in the non-fusion group (L1-2 respectively were 0.38,0.57,0.75,1.02,0.87,0.90 MPa while L4-5 respectively were 0.18,0.26,0.81,0.98,0.30,0.27 MPa) was similar to that in the physiological group,although there was some difference.Conclusion Movable artificial lumbar disc prosthesis implantation can better avoid the stress increase of adjacent intervertebral discs,and its long-term implantation in the human body is expected to reduce the incidence of degeneration of adjacent intervertebral discs.

The 17α-hydroxylase/17, 20-lyase deficiency (17-OHD) is a rare disease. The clinical characteristics and gene mutation of 2 late-diagnosed 17-OHD patients with testicular tumor admitted to our hospital from March 2018 to February 2019 were analyzed retrospectively. The two 17-OHD patients were female (46, XY). Laparoscopic abdominal exploration found undeveloped testicles in grey-yellow or grey-red in the groin and iliac fossa. The testicles were removed and showed malignancy in pathology study. Sequencing of the CYP17A1 gene identified c.1247G>A/c.1427T>C and c.985_987delTACinsAA/c.1306G>A complex heterozygous mutations. Taking together, the possibility of 17-OHD should be considered in patients with hypertension, hypokalemia, adrenal adenomatoid hyperplasia together with 46, XY gonadal dysplasia, so as to make early diagnosis and treatment, and avoid dysplastic testicular turning to malignancy.

Objective To compare the accuracy of consolidation/tumor ratio(CTR)measured at different CT thresholds for the prediction of invasiveness in small lung cancer with diameter≤2 cm using artificial intelligence-assisted measurements,and to explore the CTR thresholds and the corresponding CT thresholds for predicting lung cancer invasiveness.Methods Clinical data from 59 lung cancer patients(78 lung nodules in total)treated at Wuwei Hospital of Traditional Chinese Medicine from January 2021 to May 2023 were collected to analyze the prediction efficacy of CTR on invasiveness in small lung cancer with diameter≤2 cm measured at CT thresholds of-400,-350,-300,-250,-200,-150 HU.ROC curves were plotted to determine the optimal critical value for invasiveness prediction,followed by the corresponding CT threshold.Results The highest diagnostic efficacy for the invasiveness of lung nodules was achieved at a CT threshold of-250 HU,with an area under the curve of 0.931,sensitivity of 77.5％,specificity of 100％,and an optimal CTR threshold of 0.322.Conclusion For small lung cancers with a maximum diameter≤2 cm,CTR measured at a CT threshold of-250 HU can accurately predict lung cancer invasiveness.At CTR>0.322,the nodule is more likely to be microinvasive or invasive adenocarcinoma.

Objective:To investigate the trend of radiological diagnostic examination frequency and the related influencing factors in a general hospital in recent four years.Methods:The hospital information system and the radiology information system were used to collect the information on the numbers of the outpatients, the emergency patients, and the inpatients and the radiology examination information from 2019 to 2022. The examination frequency and proportion of various imaging equipment were counted by using the perspective table of data, and the examination items and the proportion of the radiological diagnostic examinations were calculated. The positive rates of the radiological examinations were measured from 2019 to 2022. The gender and age distribution of the patients were analyzed. Spearman correlation analysis was used to analyze the relationships between the numbers of the patients undergoing radiological examinations and the numbers of the outpatients, emergency patients and the inpatients.Results:The annual frequency of radiological diagnostic examinations from 2019 to 2022 were 307 306, 245 418, 317 250 and 325 625, respectively, with a total of 1 195 599. Among them, the proportions of CT, X-rays, bedside X-rays, bone density, gastrointestinal imaging and mammography were 59.74%, 38.04%, 1.39%, 0.42%, 0.21% and 0.19%, respectively. In each year, the proportion of CT in all radiological diagnostic examinations was 49.58%, 63.40%, 60.40% and 65.20%, respectively. The frequency of emergency CT and emergency chest CT was correlated with the number of emergency patients( r =0.63, 0.61, P<0.05), and the frequency of non-emergency CT was correlated with the number of outpatients and inpatients ( r =0.61, 0.66, P<0.05). The positive rates of the CT examinations were higher than 80% except the lowest of 79.95% in 2021. Conclusions:Radiological examinations especially CT examinations have increased significantly, and played an important role in the diagnosis of diseases. However, attention should be paid to the Justification of the CT examinations. Timely statistical analysis of radiological examination information can provide data supports and references for scientific management of radiological examinations.

Objective:To investigate the effect of different scanning modes, detector width and location in detector on high and low contrast resolution of wide-detector CT image.Methods:The Catphan600 phantom with high and low contrast resolution modules was scanned with GE Revolution CT at the same CTDI vol. The scans were performed with the detector widths of 40, 80 and 160 mm for sequential scanning mode and with the detector width/pitch combinations of 40 mm/0.516, 40 mm/0.984, 80 mm/0.508 and 80 mm/0.992 for spiral scanning mode. The resolution modules were placed at the adjacent region between two sequential scans, central and foot side edge in the longitudinal scanning range seperately. The subjective evaluation of the high and low contrast resolution was performed by two radiologists. Results:The high contrast resolution was 8 LP/cm at adjacent region between two sequential scans with the detector width of 80 mm or 160 mm in sequential scanning mode, and at the pitch of 0.5 in spiral scanning mode, while it was 7 LP/cm for the rest of detector combinations. The distinguishable diameter was 3 mm at 1% low contrast resolution at foot side edge with the detector widths of 80 mm or 160 mm in the sequential scanning mode, and it was 2 mm for all the other conditions. The distinguishable diameter was 2 mm at 1% low contrast resolution with the detector width of 40 mm and pitch 0.516 in the spiral scanning mode and it was worse with the wider detector and larger pitch.Conclusions:For the wide-detector CT, scanning mode, detector width, location in detector and pitches will affect the high and low contrast resolution to some degree. Appropriate selection should be done according to actual needs in clinical practice.

Objective:To investigate the effect of organ dose modulation (ODM) technique on reducing the breast radiation dose in chest CT scanning.Methods:In the phantom test, the PBU-2 adult chest module was used. The clinical chest scan protocol was used and three sets of scans performed on the chest module： (1) ODM off group, ODM was not used; (2) ODM part group, ODM was applied only in the breast region； (3) ODM all group, ODM was applied in the whole scan scope. Other scan parameters were same for the three groups, with smart mA applied. The volume CT dose index (CTDI vol) was recorded for all three groups. A long rod ionization chamber was placed in a fixed position in front of the right breast area to measure the breast skin dose (D). The contrast noise ratio (CNR) and the figure of merit (FOM) were measured respectively. In clinical research, 72 female patients who underwent chest CT scanning in Beijing Tongren Hospital Capital Medical University from August to November 2018 were retrospectively recruited. According to the application of ODM, the patients were divided into ODM off group (without ODM, 36 cases) and ODM part group (ODM applied in the breast region, 36 cases). The CTDI vol and the dose length product (DLP) were recorded. CNR, noise of images were measured and calculated, respectively. The image quality was evaluated by subjective evaluation scores. The one way ANOVA analysis was used in comparing the difference of CNR among the 3 groups in module test. As for clinical cases, the independent samples t test was used to compare the difference in CTDI vol, DLP, CNR and the noise between two groups; and the rank-sum test was used for comparison in image quality subjective evaluation. Results:In module test, the radiation dose was highest in ODM off group, and lowest in ODM all group. The CTDI vol were (6.90±0.02), (6.26±0.02) and (5.99±0.02) mGy, and the D values were (9.17±1.01), (8.01±0.92) and (7.58±0.87) mGy for ODM off group, ODM part group and ODM all group respectively. The CNR values of images with soft tissue algorithm reconstruction were highest in ODM off group and lowest in ODM all group, while no statistically significant difference was displayed ( P>0.05). The CNR values of the images with lung algorithm reconstruction showed the same trend, with statistically significant difference among the three groups ( F=154.732, P=0.006). The FOM of the lung and soft tissue algorithm images was maximized when the ODM was partially applied. As for clinical cases, compared with ODM off group, the dose of ODM part group showed significantly decreased, with CTDI vol decreased by 16.12% ( t=2.604, P=0.011), and the DLP decreased by 16.85% ( t=3.293, P=0.002). No significant difference was found in CNR, noise and subjective score by two doctors between two groups ( P>0.05). Conclusion:The application of ODM in chest CT imaging can reduce the radiation dose of breast with simultaneously maintaining the image quality.

Objective:To investigate the uncertainty of the dose measurements of superficial organs and the image noise in CT scanning.Methods:GE Revolution CT was used to perform 20 repeated scans on the isolated skull specimen in sequential and helical mode. The chest phantom was scanned for 45 times with the pitch 1.0 and the collimation 80 mm for two scanners (GE Revolution CT, Philips Brilliance iCT) and 40 mm for the Siemens Somatom Definition Flash CT. The volume CT dose index (CTDI vol) was maintained during the above scannings. A dosimeter was used to measure the dose at the position of the right eye lens of the specimen and the center of right breast of the chest phantom. The position of dosimeter sensor remained unchanged. The standard deviation of CT values (image noise) in the air region of cross-sectional images at the center of the sensor reconstructed with lung/soft tissue algorithms were measured. The mean values ( Av), standard deviations ( SD), coefficients of variation ( CV) and relative ranges ( RR) of the dosimetric values and the standard deviations of CT values of 3, 5, 10, 20, 30 and 45 scans were calculated. Pearson and Spearman correlation analysis were used to evaluate the correlation between the dosimetric values and the standard deviations of CT values. Results:The measured dosimetric values of the skull specimen were almost unchanged in the sequential scannings. The relative range of dose in helical mode was 10.67%. The relative ranges of the measured values of the three CT scanners for 45 scans reached 43.83%, 25.31%, and 14.32%. The standard deviations of CT values of the lung/soft tissue images varied greatly and the differences were not completely related to the dosimetric values.Conclusions:The dosimetric values of superficial organs were stable in the sequential scanning mode. The dose measurements of superficial organs and the image noise changed greatly in helical scanning mode.

OBJECTIVE: To investigate the short-term effectiveness of transverse antecubital incision in the treatment of failed closed reduction of Gartland type Ⅲ supracondylar humeral fractures (SHFs) in children. METHODS: Between July 2020 and April 2022, 20 children with Gartland type Ⅲ SHFs who failed in closed reduction were treated with internal and external condylar crossing Kirschner wire fixation through transverse antecubital incision. There were 9 boys and 11 girls with an average age of 3.1 years (range, 1.1-6.0 years). The causes of injuries were fall in 12 cases and fall from height in 8 cases. The time from admission to operation ranged from 7 to 18 hours, with an average of 12.4 hours. The healing of the incision and the occurrence of complications such as nerve injury and cubitus varus were observed after operation; the elbow flexion and extension range of motion after removing the gypsum, after removing the Kirschner wire, and at last follow-up were recorded and compared, as well as the elbow flexion and extension and forearm rotation range of motion at last follow-up between healthy and affected sides; the Baumann angle was measured on the X-ray film, and the fracture healing was observed. At last follow-up, the effectiveness was evaluated according to the Flynn elbow function evaluation criteria. RESULTS: All incisions healed by first intention, and there was no skin necrosis, scar contracture, ulnar nerve injury, and cubitus varus. Postoperative pain occurred in the radial-dorsal thumb in 2 cases. The gypsum was removed and elbow flexion and extension exercises were started at 2-4 weeks (mean, 2.7 weeks) after operation, and the Kirschner wire was removed at 4-5 weeks (mean, 4.3 weeks). All the 20 patients were followed up 6-16 months, with an average of 12.4 months. The fracture healing time was 4-5 weeks, with an average of 4.5 weeks, and there was no complication such as delayed healing and myositis ossificans. The flexion and extension range of motion of the elbow joint gradually improved after operation, and there were significant differences between the time after removing the gypsum, after removing the Kirschner wire, and at last follow-up ( P<0.017). There was no significant difference in the flexion and extension of the elbow joint and the forearm rotation range of motion between the healthy and affected sides at last follow-up ( P>0.05). There was no significant difference in Baumann angle between the time of immediate after operation, after removing the Kirschner wire, and at last follow-up ( P>0.05). According to Flynn elbow function evaluation standard, 16 cases were excellent and 4 cases were good, the excellent and good rate was 100%. CONCLUSION The treatment of Gartland type Ⅲ SHFs in children with failed closed reduction by internal and external condylar crossing Kirschner wire fixation through transverse antecubital incision has the advantages of complete soft tissue hinge behind the fracture for easy reduction and wire fixation, small incision, less complications, fast fracture healing, early functional recovery, reliable reduction and fixation, and can obtain satisfactory results.
Male ; Female ; Humans ; Child ; Child, Preschool ; Calcium Sulfate ; Humerus ; Humeral Fractures/surgery* ; Plastic Surgery Procedures ; Fracture Fixation, Internal/methods* ; Bone Wires ; Fracture Healing ; Treatment Outcome ; Range of Motion, Articular