Objective Evaluate data of 1270 cases with free flap transplant,to find the problems in the process of operation,and then to analyse its causes and how to prevent and solve it,as well as providing reference for clinical colleagues. Methods To study 1270 cases of free flaps,musculocutaneous flap and perforator flap who was treated in our hospital from October 2000 to October 2010 retrospectively. A total of 722 cases of the group were followed-up 6 months to 5 years. To detective and search the problems and imperfection from designing,harvesting,tranfer,to the management and function of donor site after free flap transplantion.And also to analysis the couse of problems and operation failure,discuss the conclude of and to provide advisable measure. Results Total 1270 free flaps were transplanted successfully except 64 can-celled or failured for some reason, the success rate was 95.0％, the postopertive necrosis rate was 3.8％.Seventy-six cases were encountered vascular complications venous crisis in 42,arterial crisis in 38.Fifty-five cases were saved successfully without surgery,and 15 cases survived completely by vessel explorative operation. Five cases were partial necrosis and 7 cases necrosis. The rate of postoperative infection of emergency cases and chronic one were 4.7％ (682 cases)and 8.8％(588 cases) which show the infective incidence of latter was higher than former. In addition, there were many other problems were found such as distal flaps necrosis,contracture,deformation,impairment function of doner site,etc. Conclusion Preventing and management timely to vessle crisis is the key to flap suvive. The principle of dissecting flap should be followed strictly,and control the indications of modified processing during flap harvest,keep the proper flap tension were technical requirements in flap transplantion. Right way of donor site closed and management of insufficient timely were equally important to prevent and solve to complications and dysfunction.

Bacterial Typing Techniques ; Campylobacter Infections ; microbiology ; Campylobacter fetus ; classification ; isolation & purification ; Humans ; Multilocus Sequence Typing

Objective:To evaluate the efficacy of 3D printed individualised prosthesis in treating bone and joint defects in upper limbs remained after earlier microsurgical repairs.Methods:From June 2019 to September 2021, 12 patients were treated in the Institute of Orthopaedic Trauma of PLA, the 80th Group Army Hospital for bone and joint defects in upper limb that had been remained after earlier repairs with soft tissue flaps. The defects were: 1 in completely severed wrist, 2 defects of digit metacarpal bone, 4 defects of interphalangeal joint, 4 defects of bones in radiocarpal joint and 1 defect of lunate bone. The area of soft tissue defect ranged from 1.5 cm×3.0 cm to 12.0 cm×18.0 cm, and the length of bone defects ranged from 2.5 to 8.5(average 3.64) cm. For incompletely severed and completely severed limbs, replantation of severed limbs (digits) were performed in the primary surgery and the repair of soft tissue defects were performed in the second stage surgery. The remaining defects of bone and joint were reconstructed by 3D printed individualised prostheses in the third stage surgery. Finger soft tissue defects were covered with a local flap in the primary surgery, and bone and joint defects were reconstructed with a 3D printed prosthesis in the second surgery. Finger soft tissue defects were covered with a local flap in the first phase, and bone and joint defects were reconstructed with a 3D printed prosthesis in the second phase. After the surgery, the bone integration between the broken end of the bone joint defect and the prosthesis was determined based on the X-ray results and the Paley fracture healing score standard. Simultaneously measured the Total Active Motion(TAM) of the forearm and hand joints. At 1, 2, 3, 6, 9 and 12 months after hospital discharge. Follow-up X-ray examinations were taken followed by examinations on the recovery of soft tissues and bones. The upper limb function was graded according to the Evaluation Trial Standards of Upper Limb Partial Functional of Hand Surgery of Chinese Medical Association.Results:Postoperative follow-up at outpatient clinic lasted for 6 to 26 months, with an average of 11.5 months. All flaps were free from necrosis and infection, also there was no infection in bones and joints. According to the Paley fracture healing scale, 10 patients were in excellent and 2 in good. In addition, according to the Evaluation Trial Standards of Upper Limb Partial Functional of Hand Surgery of Chinese Medical Association, 5 patients achieved upper limb function in excellent, 5 in good and 2 in fair. The ranges of motion of the affected wrists were 30°-42°(average 37.3°) for the implanted prostheses of distal end of radius and the radial shaft. Wrist flexion 40° to 55°(average 43.5°). The range of motion of finger and wrist was 60° to 70°(average 65.7°) with a metacarpal and phalangeal bone prosthesis.Conclusion:3D printed individually customised prostheses are safe, accurate and effective in repair of the remained bone and joint defects in upper limbs after primary and early stages of microsurgical flap repairs. It can effectively restore anatomical structures of bone and joint in upper limbs.