No abstract available.
Silver*

No abstract available.
Silver*

Introduction: The biosynthesis of nanoparticles has been proposed as a cost-effective and environmental friendly alternative to chemical and physical methods. The present study was aimed to characterise Catharanthus roseus (C. roseus)-silver nanoparticles (AgNPs) using a standardised C. roseus aqueous extract. Methods: The standardisation was performed by using Liquid Chromatography/Time-of-Flight ion trap Mass Spectrometry. An optimised C. roseus-AgNPs have been previously synthesised. Further characterisation of C. roseus-AgNPs was evaluated by zeta potential analysis and fourier transform infrared spectroscopy (FTIR). Results: The chromatography analysis has revealed presence of thirteen possible indole alkaloids in C. roseus extract which were lochrovicine, lochnerine, vinleurosine, vindolinine, tabersonine, catharanthine, serpentine, catharosine, vincristine, catharine, ajmalicine, vinleurosine, and vindolicine. Zeta potential analysis exhibited the value at -16.6 mV. FTIR spectrum of C. roseus aqueous extract showed the absorption band at 3210.83 cm-1 (C-H stretch), 2934.11 (C-H bond), 1578.15 (N=O stretch), 1388.76 and 1314.89 (N=O bend), 1119.29 (C-O bond) and 729.94 (C-Cl bond). In comparison, FTIR spectrum of C. roseus-AgNP s showed the absorption band at 2925.01 and 2924.97 (C-H bond), 1622.93 (C-C=C symmetric stretch), 1383.19 and 1384.13 (N-O bend), 1037.92/1038.76/1238.3/1117.2 (C-O bond), 3169.4 (O-H bond), 774.59 and 691.53 (C-Cl bond). Conclusion: The present findings have shown that the C. roseus aqueous extract contains alkaloids that may responsible as reducing and stabilising agents in the synthesis of AgNPs.
silver nanoparticles

PURPOSE: To design and test the CT simulator phantom for geometrical test. MATERIAL AND METHODS: The PMMA phantom was designed as a cylinder which is 20 cm in diameter and 24 cm in length, along with a 25x25x31 cm3 rectangular parallelepiped. Radio-opaque wires of which diameter is 0.8 mm are attached on the other surface of the phantom as a spiral. The rectangular phantom was made of four 24x24x0.5 cm3 square plates and each plate had a 24x24 cm2, 12x12 cm2, 6x6 cm2 square line. The squares were placed to face the cylinder at angles 0degrees, 15degrees, 30degrees, respectively. The rectangular phantom made it possible to measure the field size, couch angle, the collimator angle, the isocenter shift and the SSD, the measurements of the gantry angle from the cylindrical part. A virtual simulation software, AcQSimTM, offered various conditions to perform virtual simulations and these results were used to perform the geometrical quality assurance of CT simulator. RESULTS: A 0.3~0.5 mm difference was found on the 24 cm field size which was created with the DRR measurements obtained by scanning of the rectangular phantom. The isocenter shift, the collimator rotation, the couch rotation, and the gantry rotation test showed 0.5~1 mm, 0.5~1degrees0.5~1degrees, and 0.5~ 1degreesdifferences, respectively. We could not find any significant differences between the results from the two scanning methods. CONCLUSION: The geometrical test phantom developed in the study showed less than 1 mm (or 1degrees) differences. The phantom could be used as a routine geometrical QC/QA tools, since the differences are within clinically acceptable ranges.
Polymethyl Methacrylate ; Silver Sulfadiazine

No abstract available.
Eating ; Female ; Humans ; Silver

This study was done to evaluate whether there were any differences in microleakage of class V composite restorations according to restoration site and cavity size. Total sixty-four restorations were made in molar teeth using Esthet-X. Small (2 x 2 x 1.5 mm) and large (4 x 2 x 1.5 mm) restorations were made at the buccal/lingual surface and the proximal surface each. After 1,000 times of thermocycling (5degrees C - 55degrees C), resin replica was made and the percentage of marginal gap to the whole periphery of the restoration was estimated from SEM evaluation. Thermocycled tooth was dye penetrated with 50% silver nitrate solution. After imbedding in an auto-curing resin, it was serially ground with a thickness of 0.25 mm. Volumetric microleakage was estimated after reconstructing three dimensionally. Two-way ANOVA and independent T-test for dye volume, Mann-Whitney U test for the percentage of marginal gap, Spearman's rho test for the relationship between two techniques were used. The results were as follows: 1. The site and size of the restoration affected on the microleakage of restoration. Namely, much more leakage was seen in the proximal and the large restorations rather than the buccal/lingual and the small restorations. 2. Close relationship was found between two techniques (Correlation coefficient = 0.614 / P = 0.000). Within the limits of this study, it was noted that proximal and the large restorations leaked more than buccal/lingual and the small restorations. Therefore, it should be strictly recommended large exposure of margins should be avoided by reducing unnecessary tooth reduction.
Molar ; Silver Nitrate ; Tooth

No abstract available.
Argyria ; Colloids ; Nails ; Silver

No abstract available.
Argyria ; Colloids ; Nails ; Silver

No abstract available.
Gels* ; Lipopolysaccharides* ; Silver* ; Sodium*

Established microleakage tests have their own disadvantages. In this study, 3D reconstruction method was tried to overcome these disadvantages. Four types of microleakage tests were used and relationships among them were estimated: penetrated dye volume; marginal adaptability; degree of dye penetration and relative penetrated length to cavity wall. Twenty-four Class V cavities were bulk filled with composite (Esthet X) following surface treatments: N group (no treatment); E group (etching only); T group (etching + Prime & Bond NT). 50% silver nitrate was used as a dye solution after thermocycling (5degrees C & 55degrees C, 1,000 times). Teeth were serially ground with a thickness of 0.2 mm. Volume of dye penetration was estimated from a three-dimensionally reconstructed image with a software (3D-DOCTOR). Percentage of margin without gap was estimated from SEM and degree of dye penetration and the relative length of dye penetration to overall cavity wall were also estimated. ANOVA and Scheffe test for dye volume, Kruskal-Wallis and Mann-Whitney test for marginal quality, Spearman's rho test for checking of relationships among methods were used. The results were as follows: 1. Dye penetration could be seen from several directions, furthermore, its volumetric estimation was possible. 2. Reverse relationship was found between dye volume and marginal quality (r = -0.881 / p = 0.004). 3. Very low relationship was seen between dye volume and two-dimensional tests (degree of dye penetration and relative length). However, 2D evaluation methods showed high relationship (p = 0.002-0.054) each other. 4. Three times vertical section could be recommended as a 2D test.
Silver Nitrate ; Tooth*