OBJECTIVE: To explore the advantages and effectiveness of the independently developed intelligent orthopedic robot-assisted distal locking of femoral intramedullary nails. METHODS: Thirty-two adult cadaveric femur specimens were randomly divided into two groups, with 16 specimens in each group. The experimental group used the intelligent orthopedic robot to assist in the distal locking of femoral intramedullary nail holes, while the control group used the traditional method of manual locking under X-ray fluoroscopy. The locking time, fluoroscopy times, and the success rate of first locking were recorded and compared between the two groups. RESULTS: The locking time of the experimental group was (273.94±38.67) seconds, which was shorter than that of the control group [(378.38±152.72) seconds], and number of fluoroscopies was (4.56±0.81) times, which was less than that of the control group [(8.00±3.98) times]. The differences were significant [ MD=73.054 (-37.187, 85.813), P=0.049; MD=1.969 (-1.437, 2.563), P=0.002]. The first locking success rate of the experimental group was 100% (16/16), which was significantly higher than that of the control group (68.75%, 11/16) ( P=0.043). CONCLUSION The efficiency of distal locking of femoral intramedullary nails assisted by the intelligent orthopedic robot is significantly higher than that of the traditional manual locking method under fluoroscopy, as it can markedly reduce the time required for distal locking of femoral intramedullary nails, decrease intraoperative radiation exposure, and increase the success rate of locking.
Humans ; Fracture Fixation, Intramedullary/instrumentation* ; Bone Nails ; Fluoroscopy ; Femur/diagnostic imaging* ; Femoral Fractures/surgery* ; Robotic Surgical Procedures/instrumentation* ; Cadaver ; Adult ; Robotics ; Male

OBJECTIVE: To evaluate precise assessment methods for predicting the optimal acetabular cup size in total hip arthroplasty (THA). METHODS: A clinical data of 73 patients (80 hips) who underwent primary THA between December 2022 and July 2024 and met the inclusion criteria was analyzed. There were 39 males and 34 females with an average age of 66.3 years (range, 56-78 years). Among them, 66 cases were unilateral THA and 7 were bilateral THAs. There were 29 patients (34 hips) of osteoarthritis, 35 patients (35 hips) of femoral neck fractures, and 9 patients (11 hips) of osteonecrosis of the femoral head. Based on anteroposterior pelvic X-ray films, three methods were employed to predict acetabular cup size, including preoperative template planning, radiographic femoral head diameter (FHD) measurement, and intraoperative FHD measurement. The predicted acetabular cup sizes from these methods were compared with the actual implanted sizes. RESULTS: The predicted acetabular cup sizes using the preoperative template planning, radiographic FHD measurement, and intraoperative FHD measurement were (51.25±2.81), (49.72±3.11), and (49.90±2.74) mm, respectively, compared to the actual implanted cup size of (50.57±2.74) mm, with no significant difference ( P>0.05). Regarding agreement with the actual implanted cup size, the preoperative template planning achieved exact matches in 35 hips (43.75%), one-size deviation in 41 hips (51.25%), and two-size deviations in 4 hips (5%); the radiographic FHD measurement achieved exact matches in 12 hips (15%), one-size deviation in 57 hips (71.25%), and two-size deviations in 11 hips (13.75%); and the intraoperative FHD measurement achieved exact matches in 26 hips (32.5%), one-size deviation in 52 hips (65%), and two-size deviations in 2 hips (2.5%). There were significant differences in agreement distributions between the three methods and the actual implanted cup sizes ( H=18.579, P<0.001). CONCLUSION The intraoperative FHD measurement, as a simple, cost-effective, and accurate method, effectively guides acetabular cup selection, reduces the risk of prosthesis wear, enhances postoperative joint stability.
Humans ; Arthroplasty, Replacement, Hip/instrumentation* ; Male ; Female ; Middle Aged ; Acetabulum/diagnostic imaging* ; Aged ; Hip Prosthesis ; Prosthesis Design ; Femur Head/surgery* ; Osteoarthritis, Hip/surgery* ; Radiography ; Femoral Neck Fractures/surgery* ; Femur Head Necrosis/surgery*

OBJECTIVE: To investigate the effectiveness of using 3 hollow compression screws combined with 1 screw off-axis fixation under the guidance of three-dimensional (3D) printed guide plate with mortise-tenon joint structure (mortise-tenon joint plate) for the treatment of Pauwels type Ⅲ femoral neck fractures. METHODS: A clinical data of 78 patients with Pauwels type Ⅲ femoral neck fractures, who were admitted between August 2022 and August 2023 and met the selection criteria, was retrospectively analyzed. The operations were assisted with mortise-tenon joint plates in 26 cases (mortise-tenon joint plate group) and traditional guide plates in 28 cases (traditional plate group), and without guide plates in 24 cases (control group). There was no significant difference in the baseline data of gender, age, body mass index, cause of injury, and fracture side between groups ( P>0.05). The operation time, intraoperative blood loss, frequency of intraoperative fluoroscopy, incision length, incidence of postoperative deep vein thrombosis of lower extremity, pain visual analogue scale (VAS) score at 1 week after operation, and Harris score of hip joint at 3 months after operation were recorded and compared. X-ray re-examination was taken to check the quality of fracture reduction, fracture healing, and the shortening length of the femoral neck at 3 months after operation, and the incidences of internal fixation failure and osteonecrosis of the femoral head during operation. RESULTS: Compared with the control group, the operation time, intraoperative blood loss, and frequency of intraoperative fluoroscopy reduced in the two plate groups, and the quality of fracture reduction was better, but the incision was longer, and the differences were significant ( P<0.05). The operation time and intraoperative blood loss were significantly higher in the traditional plate group than in the mortise-tenon joint plate group ( P<0.05), the incision was significantly longer ( P<0.05); and the difference in fracture reduction quality and the frequency of intraoperative fluoroscopy was not significant between two plate groups ( P>0.05). There was 1 case of deep vein thrombosis of lower extremity in the traditional plate group and 1 case in the control group, while there was no thrombosis in the mortise-tenon joint plate group. There was no significant difference in the incidence between groups ( P>0.05). All patients were followed up 12-15 months (mean, 13 months). There was no significant difference in VAS score at 1 week and Harris score at 3 months between groups ( P>0.05). Compared with the control group, the fracture healing time and the length of femoral neck shortening at 3 months after operation were significantly shorter in the two plate groups ( P<0.05). There was no significant difference between the two plate groups ( P>0.05). There was no significant difference in the incidences of non-union fractures, osteonecrosis of the femoral head, or internal fixation failure between groups ( P>0.05). CONCLUSION For Pauwels type Ⅲ femoral neck fractures, the use of 3D printed guide plate assisted reduction and fixation can shorten the fracture healing time, reduce the incidence of postoperative complications, and be more conducive to the early functional exercise of the affected limb. Compared with the traditional guide plate, the mortise-tenon joint plate can reduce the intraoperative bleeding and shorten the operation time.
Humans ; Femoral Neck Fractures/diagnostic imaging* ; Bone Plates ; Fracture Fixation, Internal/instrumentation* ; Male ; Female ; Retrospective Studies ; Middle Aged ; Bone Screws ; Adult ; Aged ; Treatment Outcome ; Printing, Three-Dimensional ; Operative Time

OBJECTIVE: To investigate short-term effectiveness of using expert adolescent lateral femoral nail (EALFN) in treating femoral shaft fractures in older children and adolescents. METHODS: A retrospective analysis was conducted on the clinical data of 17 patients with femoral shaft fractures who met the inclusion criteria and were admitted between July 2020 and June 2024. All fractures were fixed with EALFN after reduction. There were 11 males and 6 females, with a mean age of 13.3 years (range, 11-16 years). The average body weight was 51.2 kg (range, 40-84 kg), and the average height was 162.1 cm (range, 150-172 cm). The causes of injury included traffic accidents ( n=9), falling from height ( n=1), and simple falls ( n=7). One patient had an open fracture treated with an external fixator and experienced delayed fracture healing. The remaining patients were closed fractures, with an average time from injury to operation of 5.8 days (range, 2-10 days). Operation time and postoperative hospital stay were documented. During follow-up, X-ray films were taken to observe the fracture healing, and the bilateral femoral length, femoral neck-shaft angle, widest femoral neck diameter (FND), and articular trochanteric distance (ATD) were measured at last follow-up. Hip function was assessed using the Harris score. The differences in the all indicators between the healthy and affected sides were compared. RESULTS: The operation time ranged from 65 to 130 minutes (mean, 94.1 minutes). Postoperative hospital stay ranged from 5 to 40 days (mean, 16.7 days). All patients were followed up 7-36 months (mean, 14.4 months). One patient exhibited delayed fracture healing during follow-up. The distal locking nail was removed at 6 months after operation, and partial weight-bearing was initiated following dynamic fracture stabilization. The fracture healing was achieved, and the intramedullary nail was removed at 24 months after operation. The other fractures healed with the healing time of 6-20 months (mean, 9.6 months), and the intramedullary nails were removed. During follow-up, no femoral fracture, abnormal development of the greater trochanter, or ischemic necrosis of the femoral head occurred. At last follow-up, there was no significant difference in femoral length, femoral neck-shaft angle, FND, ATD, or Harris score between the affected and healthy sides ( P>0.05). CONCLUSION For older children and adolescents with femoral neck fractures, the application of EALFN fixation aligns more closely with the principles of intramedullary central fixation and rapid rehabilitation. This approach is associated with fewer complications and superior short-term effectiveness.
Humans ; Male ; Femoral Fractures/surgery* ; Female ; Child ; Adolescent ; Retrospective Studies ; Bone Nails ; Fracture Fixation, Intramedullary/instrumentation* ; Fracture Healing ; Treatment Outcome

OBJECTIVE: To explore the effectiveness of proximal femoral nail antirotation (PFNA) combined with minimally invasive clamp reduction technique by Kocher pincers in the treatment of irreducible intertrochanteric femoral fracture in the elderly. METHODS: The clinical data of 35 elderly patients with irreducible intertrochanteric femoral fractures who were treated with PFNA combined with minimally invasive clamp reduction technique by Kocher pincers between January 2016 and December 2022 were retrospectively analysed. There were 16 males and 19 females, aged from 63 to 95 years (mean, 75.2 years). The causes of injury included traffic accident in 3 cases and falling in 32 cases. The time from injury to operation was 2-11 days (mean, 3.6 days). According to AO/Orthopaedic Trauma Association (AO/OTA) classification system for intertrochanteric fractures, there were 14 cases of type A1, 18 cases of type A2, and 3 cases of type A3. According to the displacement of fracture by intraoperative fluoroscopy, there were 5 cases with only coronal displacement, 17 cases with only sagittal displacement, and 13 cases with both coronal and sagittal displacement. The operation time, intraoperative blood loss, rate of hemoglobin decline at 1 day after operation, length of hospital stay, and fracture healing time were recorded. The reduction quality of fracture during operation was evaluated according to reduction quality criteria proposed by Chang et al. The Harris scoring system was used to evaluate the hip joint function at last follow-up. RESULTS: The operation time was 45-105 minutes (mean, 54.4 minutes); the intraoperative blood loss was 80-300 mL (mean, 116.3 mL). The reduction quality of fracture during operation was good in 22 cases (62.9%) and acceptable in 13 cases (37.1%). The rate of hemoglobin decline at 1 day after operation ranged from 6.2% to 18.6% (mean, 10.2%); the length of hospital stay was 5-18 days (mean, 7.2 days). One case died of respiratory failure due to pulmonary infection, 2 cases were lost to follow-up, and the remaining 32 cases were followed up 6-24 months (mean, 10.6 months). All 32 patients achieved bony union and the healing time was 3-9 months (mean, 3.6 months). There was no complication such as incision infection, internal fixation failure, or coxa varus during follow-up. At last follow-up, the Harris score of hip joint was 67-96 (mean, 88.9); among them, 19 cases were excellent, 10 cases were good, 2 cases were fair, and 1 case was poor, with an excellent and good rate of 90.6%. CONCLUSION For the elderly patients with irreducible intertrochanteric femoral fracture, the application of PFNA combined with minimally invasive clamp reduction technique by Kocher pincers can achieve high-quality fracture reduction, which has the advantages of simple reduction operation, less trauma, and can avoid the radiation exposure of operators during maintenance reduction.
Humans ; Male ; Female ; Aged ; Minimally Invasive Surgical Procedures/methods* ; Hip Fractures/diagnostic imaging* ; Bone Nails ; Aged, 80 and over ; Retrospective Studies ; Fracture Fixation, Intramedullary/instrumentation* ; Middle Aged ; Treatment Outcome ; Fracture Fixation, Internal/instrumentation* ; Fracture Healing ; Femoral Fractures/surgery*

OBJECTIVE: To investigate whether adding 1 transverse screw (TS) to the triangular parallel cannulated screw (TPCS) fixation has a mechanical stability advantage for Pauwels type Ⅲ femoral neck fractures by conducting finite element analysis on four internal fixation methods. METHODS: Based on CT data of a healthy adult male volunteer's femur, three Pauwels type Ⅲ femoral neck fracture models (Pauwels angle 70°, Pauwels angle 80°, and Pauwels angle 70° combined with bone defect) were constructed using Mimics 21.0 software and SolidWorks 2017 software. Four different internal fixation models were built at the same time, including TPCS, TPCS+TS, three cross screws (TCS), and TPCS+medial buttress plate (MBP). The mechanical stability of different models under the same load was compared by finite element analysis. RESULTS: The femoral model established in this study exhibited a maximum stress of 28.62 MPa, with relatively higher stress concentrated in the femoral neck. These findings were comparable to previous studies, indicating that the constructed femoral finite element model was correct. The maximum stress of internal fixation in finite element analysis showed that TCS was the lowest and TPCS+MBP was the highest in Pauwels angle 70° and 80° models, while TPCS+TS was the lowest and TCS was the highest in Pauwels angle 70° combined with bone defect model. The maximum displacement of internal fixation in each fracture model was located at the top of the femoral head, with TCS having the highest maximum displacement of the femur. The maximum stress of fracture surface in finite element analysis showed that TCS was the lowest and TPCS was the highest in the Pauwels angle 70° model, while TPCS+MBP was the lowest and TPCS/TCS were the highest in the Pauwels angle 80° model and the Pauwels angle 70° combined with bone defect model, respectively. The maximum displacement of fracture surfece analysis showed that TPCS+MBP was the lowest and TCS was the highest in Pauwels angle 70° and 80° models, while TPCS+TS was the lowest and TCS was the highest in Pauwels angle 70° combined with bone defect model. CONCLUSION For Pauwels type Ⅲ femoral neck fractures, the biomechanical stability of TPCS+TS was superior to that of TPCS alone and TCS, but it has not yet reached the level of TPCS+MBP.
Finite Element Analysis ; Humans ; Femoral Neck Fractures/diagnostic imaging* ; Bone Screws ; Fracture Fixation, Internal/instrumentation* ; Male ; Bone Plates ; Stress, Mechanical ; Biomechanical Phenomena ; Tomography, X-Ray Computed ; Adult ; Femur Neck/surgery*

OBJECTIVE: To investigate the effect of stretch on long non-coding RNA taurine upregulated gene 1 (TUG1)-mediated miR-545-3p/cannbinoida receptor 2 (CNR2) pathway regulating bone regeneration in the distraction area of rats during distraction osteogenesis. METHODS: Thirty-six 10-week-old male Sprague Dawley rats were randomly divided into 3 groups ( n=12 in each group): group A (femoral fracture+injection of interfering RNA), group B (distraction osteogenesis+injection of interfering RNA), and group C (distraction osteogenesis+injection of TUG1). Groups A and B were injected with 60 μg of interfering RNA at the beginning of incubation period (immediate after operation), the beginning of distraction phase (7 days after operation), and the end of distraction phase (21 days after operation), and group C was injected with 60 μg of synthetic TUG1 in vivo interfering sequence at the same time. The general situation of rats in each group was observed during the experiment. The mineralization of fracture space or distraction area was observed by X-ray films at 21, 35, and 49 days after operation. At 49 days after operation, the samples of the distraction area were taken for HE staining to observe the mineralization, and real-time fluorescence quantitative PCR (qRT-PCR) was used to detect the expressions of osteoblast-related genes such as TUG1, miR-545-3p, CNR2, alkaline phosphatase (ALP), osteocalcin (OCN), and osteopontin (OPN). Blood samples were collected from the abdominal aorta of the rats, and the expressions of ALP and C terminal telopeptide of type Ⅰ (CTX-Ⅰ) protein were detected by ELISA assay. RESULTS: The results of X-ray film and HE staining observations showed that osteogenesis in group C was superior to groups A and B at the same time point. The results of qRT-PCR showed that the relative mRNA expressions of TUG1, CNR2, ALP, OCN, and OPN in group C were significantly higher than those in group A and group B, and the relative mRNA expression of miR-545-3p in group C was significantly lower than that in group A and group B ( P<0.05). The relative mRNA expressions of TUG1 and ALP in group B were significantly higher than those in group A, and the relative mRNA expression of miR-545-3p in group B was significantly lower than that in group A ( P<0.05). There was no significant difference in the relative mRNA expressions of CNR2, OCN, and OPN between group A and group B ( P>0.05). The results of ELISA showed that the expressions of ALP and CTX-Ⅰ protein were significantly higher in group C than in group A and group B, and in group B than in group A ( P<0.05). CONCLUSION Under the action of stretch, the expression of TUG1 in the femoral distraction area of rats increases, which promotes the expression of CNR2 by inhibiting the expression of miR-545-3P, which is helpful to the mineralization of the extension area and osteogenesis.
Animals ; MicroRNAs/genetics* ; Rats, Sprague-Dawley ; Male ; Osteogenesis, Distraction/methods* ; Rats ; RNA, Long Noncoding/metabolism* ; Osteopontin/genetics* ; Osteogenesis ; Bone Regeneration ; RNA, Small Interfering/genetics* ; Osteocalcin/genetics* ; Alkaline Phosphatase/metabolism* ; Osteoblasts/cytology* ; Signal Transduction ; Femoral Fractures/surgery*

OBJECTIVE: To investigate the effectiveness of Holosight robotic navigation-assisted percutaneous cannulated screw fixation for femoral neck fractures. METHODS: A retrospective analysis was conducted on 65 patients with femoral neck fractures treated with cannulated screw fixation between January 2022 and February 2024. Among them, 31 patients underwent robotic navigation-assisted screw placement (navigation group), while 34 underwent conventional freehand percutaneous screw fixation (freehand group). Baseline characteristics, including age, gender, fracture side, injury mechanism, Garden classification, Pauwels classification, and time from injury to operation, showed no significant differences between the two groups ( P>0.05). The operation time, intraoperative blood loss, fluoroscopy frequency, fracture healing time, and complications were recorded and compared, and hip function was evaluated by Harris score at last follow-up. Postoperative anteroposterior and lateral hip X-ray films were taken to assess screw distribution accuracy, including deviation from the femoral neck axis, inter-screw parallelism, and distance from screws to the femoral neck cortex. RESULTS: No significant difference was observed in operation time between the two groups ( P>0.05). However, the navigation group demonstrated superior outcomes in intraoperative blood loss, fluoroscopy frequency, deviation from the femoral neck axis, inter-screw parallelism, and distance from screws to the femoral neck cortex ( P<0.05). No incision infections or deep vein thrombosis occurred. All patients were followed up 12-18 months (mean, 16 months). In the freehand group, 1 case suffered from cannulated screw dislodgement and nonunion secondary to osteonecrosis of femoral head at 1 year after operation, 1 case suffered from screw penetration secondary to osteonecrosis of femoral head at 5 months after operation; and 1 case suffered from nonunion secondary to osteonecrosis of femoral head at 6 months after operation in the navigation group. All the 3 patients underwent internal fixators removal and total hip arthroplasty. There was no significant difference in the incidence of complications between the two groups ( P>0.05). The fracture healing time and hip Harris score at last follow-up in the navigation group were significantly better than those in the freehand group ( P<0.05). CONCLUSION Compared to freehand percutaneous screw fixation, Holosight robotic navigation-assisted cannulated screw fixation for femoral neck fractures achieves higher precision, reduced intraoperative radiation exposure, smaller incisions, and superior postoperative hip function recovery.
Humans ; Femoral Neck Fractures/diagnostic imaging* ; Bone Screws ; Fracture Fixation, Internal/instrumentation* ; Male ; Female ; Retrospective Studies ; Robotic Surgical Procedures/methods* ; Middle Aged ; Aged ; Adult ; Treatment Outcome ; Operative Time ; Fracture Healing ; Surgery, Computer-Assisted/methods* ; Fluoroscopy

OBJECTIVE: To explore the effectiveness of additional anti-rotation steel plate assisted intramedullary nail technology in treatment of aseptic femoral non-union patients. METHODS: A retrospective analysis was conducted on 21 patients with aseptic femoral non-union who admitted between September 2020 and October 2024 and treated with additional anti-rotation steel plate assisted intramedullary nail technology. There were 17 males and 4 females, aged 25-67 years (mean, 44 years). There were 19 cases of femoral anterograde intramedullary nail fixation, 1 case of femoral retrograde intramedullary nail fixation, and 1 case of steel plate fixation with fatigue fracture. There were 9 cases of hypertrophic non-union and 12 cases of atrophic non-union. All patients had varying degrees of fracture end atrophy/sclerosis. Among them, 20 patients who were fixed with intramedullary nails underwent removal of soft tissue and hardened bone at the fracture end, and cortical treatment resulted in the appearance of "chili sign" at the fracture end. Iliac bone grafting and anti-rotation steel plate fixation were performed. One patient with steel plate fixation was removed the steel palte and fixed with a retrograde intramedullary nail, while the hardened bone at the fracture end was removed, iliac bone grafting and anti-rotation steel plate fixation were performed. Postoperative follow-up observation included the incision healing, maximum knee flexion range of motion, bone healing, length of lower limbs, and subjective satisfaction. The lower extremity functional scale (LEFS) score was used to evaluate the lower limb function. RESULTS: All incisions healed by first intention. All patients were followed up 7-26 months (mean, 15.5 months). At last follow-up, the femoral fracture healed with the obvious callus formation at the fracture end; the maximum knee flexion range of motion was 95°-127° (mean, 112.67°). The LEFS score increased from 29.9±6.7 before operation to 75.9±3.0 at last follow-up, and the difference was significant (t=-29.622, P<0.001). Except for 1 patient who underwent intramedullary nail dynamic treatment before operation and had a lower limb shortening of about 0.9 cm, the other patients had bilateral lower limbs of equal length. All patients had no postoperative infections, mal-union of fractures, deep vein thrombosis, joint stiffness, or other complications. CONCLUSION The use of additional anti-rotation steel plate assisted intramedullary nail technology in the treatment of aseptic femoral non-union not only overcomes the drawbacks of insufficient stability at the fracture end of intramedullary nails, but also overcomes the shortcomings of biased fixation with steel plates. It has the advantages of minimal trauma, effective maintenance of fracture stability, and ideal postoperative functional recovery, making it an effective treatment for aseptic femoral non-union.
Humans ; Male ; Fracture Fixation, Intramedullary/instrumentation* ; Female ; Bone Plates ; Middle Aged ; Adult ; Femoral Fractures/surgery* ; Retrospective Studies ; Bone Nails ; Aged ; Fractures, Ununited/surgery* ; Treatment Outcome ; Bone Transplantation/methods* ; Steel ; Fracture Healing

OBJECTIVE: To compare the effectiveness of dynamic fixation and plate augmentation combined with bone grafting for femoral nonunion after interlocking intramedullary nails. METHODS: Between January 2008 and December 2022, a total of 128 patients who developed femoral nonunion following static fixation with interlocking intramedullary nailing were retrospectively analyzed. All patients underwent either dynamic intramedullary nail fixation or plate fixation with bone grafting while retaining the original intramedullary nail. There were 104 males and 24 females;the age ranged from 19 to 59 years old with an average of(32.70±9.21) years old. Patients were categorized into dynamization group and plate group based on the distinct treatment modalities. There were 67 patients in the dynamization group, comprising 54 males and 13 females. The age range was from 19 to 58 years old, with a mean age of (32.68±9.33) years old. All patients underwent open reduction and anterograde interlocking intramedullary nail fixation. Dynamic fixation was implemented between 10 and 28 months postoperatively.The plate group comprised 61 patients, of whom 50 were male and 11 were female. The age distribution ranged from 20 to 59 years old, with a mean age of (32.84±9.07) years old. All patients underwent open reduction and anterograde interlocking intramedullary nailing. Plate reinforcement fixation was performed between 10 and 30 months postoperatively. The incision length, duration of surgery, intraoperative blood loss, hospitalization period, fracture healing status, and incidence of complications were compared between the two groups of patients. RESULTS: All patients were followed up for a minimum duration of 1 year. The mean follow-up period for the dynamization group was(26.12±11.82) months, compared to (26.57±12.48) months for the plate group. No statistically significant difference was observed between the two groups (P>0.05). The incision size (2.73±1.21) cm, operation time (22.73±3.20) min and blood loss (19.06±6.22) ml in the dynamization group were significantly less than those in the plate group(22.53±2.24) cm, (126.40±13.91) min and(237.36±81.56) ml, respectively(P<0.05). All nonunion in the plate group were successfully healed, and the healing time duration ranged from 4 to 7 months with an average of(6.16±0.99) months. In the dynamization group, a total of 42 patients achieved fracture healing, with a healing duration ranging from 4 to 8 months with an average of (6.26±1.23) months. There was significant difference in healing rate between 2 groups (P<0.05), but there was no significant difference in healing time between 2 groups (P>0.05). The average treatment cost was(17 700.18±4 846.27) yuan in the plate group and (334.24±18.16) yuan in the dynamization group, and there was significant difference in costs between 2 groups (P<0.05). CONCLUSION Either dynamic fixation or plate augmentation combined with bone grafting is an effective method, but dynamic fixation is superior to plate augmentation combined with bone grafting for the treatment of femoral hyperplastic nonunion after interlocking intramedullary nails. Dynamic fixation offers several advantages, including simplified procedures, reduced trauma, and cost-effectiveness in medical expenses, making it superior to additional plate fixation combined with bone grafting. However, dynamic fixation is not suitable for the treatment of femoral atrophic nonunion.
Humans ; Male ; Female ; Adult ; Middle Aged ; Fracture Fixation, Intramedullary/adverse effects* ; Femoral Fractures/surgery* ; Fractures, Ununited/surgery* ; Bone Nails ; Retrospective Studies ; Bone Plates ; Young Adult