Study on mandibular movement trajectory and virtual occlusal pre-adjustment under light and heavy bite force.
10.3760/cma.j.cn112144-20220507-00243
- VernacularTitle:轻咬合和重咬合状态对下颌运动轨迹及虚拟预调
的影响
- Author:
Jia Yi ZHU
1
;
Jun Jie WANG
2
;
Yu Xuan WANG
1
;
Jing Wen YANG
1
;
Ting JIANG
1
Author Information
1. Department of Prosthodontics, Peking University School and Hospital of Stomatology & National Center of Stomatology & National Clinical Research Center for Oral Diseases & National Engineering Research Center of Oral Biomaterials and Digital Medical Devices & Beijing Key Laboratory of Digital Stomatology, Beijing 100081, China.
2. Beijing WeCare Digital Technology Co., Ltd, Beijing 100076, China.
- Publication Type:Journal Article
- MeSH:
Male;
Female;
Humans;
Bite Force;
Tooth;
Mandible;
Molar;
Occlusal Adjustment
- From:
Chinese Journal of Stomatology
2023;58(1):50-56
- CountryChina
- Language:Chinese
-
Abstract:
Objective: To investigate the influence of light and heavy bite force on the mandibular movement trajectories, and the influence of bite force on virtual occlusal pre-adjustment of digital full crown. Methods: From October 2021 to March 2022, 10 postgraduate volunteers (3 males and 7 females, aged 22-26 years) were recruited from Peking University School and Hospital of Stomatology. Maxillary and mandibular digital models of the participants were obtained by intraoral scanning. Jaw relations were digitally transferred under heavy bite force and mandibular movement trajectories under light and heavy bite force were recorded by jaw motion analyser. Three mandibular markers were chosen, namely the mesial proximal contact point of the central incisor (incisal point) and the mesial buccal cusp tips of the bilateral first molars. The three-dimensional displacements of the markers under two kinds of bite force in the intercuspal position (ICP), the sagittal projection of the three-dimensional displacements in the protrusive edge-to-edge position, and the coronal projection of the three-dimensional displacements in the lateral edge-to-edge position of upper and lower posterior teeth were measured. Single-sample t-test was used to compare the three-dimensional displacements and the corresponding sagittal projection and coronal projection with 0, respectively. The left maxillary central incisor and left mandibular first molar were virtually prepared by the reverse engineering software. Then dental design software was used to design digital full crown using the copy method. The mandibular movement trajectories under light and heavy bite force were separately used to guide virtual occlusal pre-adjustment. The three-dimensional deviations (mean deviations and root mean square) between the lingual surface of the left maxillary central incisor or the occlusal surface of the left mandibular first molar and that of the natural tooth before preparation were calculated (light bite force group and heavy bite force group), and the differences between the two groups were compared by the paired t-test. Results: Under the two kinds of bite force, the three-dimensional displacements of the markers in the ICP were (0.217±0.135), (0.210±0.133) and (0.237±0.101) mm, respectively; the sagittal projection of the three-dimensional displacements of the markers in the protrusive edge-to-edge position were (0.204±0.133), (0.288±0.148) and (0.292±0.136) mm, respectively; the coronal projection of the three-dimensional displacements of the mesial buccal cusp tips of the bilateral first molars in the lateral edge-to-edge position were (0.254±0.140) and (0.295±0.190) mm, respectively. The differences between the above displacements and 0 were statistically significant (P<0.05). The results of occlusal pre-adjustment showed that the mean deviations of the lingual surface of the left maxillary central incisor in the light and heavy bite force groups were (0.215±0.036) and (0.195±0.041) mm (t=3.95, P=0.004), respectively. The mean deviations of the occlusal surface of the left mandibular first molar were (0.144±0.084) and (0.100±0.096) mm (t=0.84, P=0.036), respectively. Conclusions: Both the light and heavy bite force have an influence on the mandibular movement trajectories. Virtual occlusal pre-adjustment of prostheses with mandibular movement trajectories under heavy bite force can obtain morphology of lingual or occlusal surfaces closer to the natural teeth before preparation.
