Influence of fracture resistance of prosthesis with different thickness of ferrule restored with fiber post and resin core and crown
10.3760/cma.j.issn.1002-0098.2018.11.009
- VernacularTitle: 牙本质肩领厚度对纤维桩核冠修复后牙体抗折性能的影响
- Author:
Shuying YANG
1
;
Yongxiang ZENG
2
;
He CAI
3
;
Min ZHANG
4
;
Yongjin CHEN
4
;
Jian WANG
3
Author Information
1. Department of Prosthodontics, West China Hospital of Stomatology, Sichuan University & State Key Laboratory of Oral Diseases & National Clinical Research Center for Oral Diseases, Chengdu 610041, China (Present address: Department of General Dentistry & Emergency, School of Stomatology, The Fourth Military Medical University & State Key Laboratory of Military Stomatology & National Clinical Research Center for Oral Diseases & Shaanxi International Joint Research Center for Oral Diseases, Xi′an 710032, China)
2. Department of Prosthodontics, West China Hospital of Stomatology, Sichuan University & State Key Laboratory of Oral Diseases & National Clinical Research Center for Oral Diseases, Chengdu 610041, China(Prensent address: Department of Cariology and Endodontology, Stomatological Hospital of Chongqing Medical University & Chongqing Key Laboratory of Oral Diseases and Biomedical Sciences & Chongqing Municipal Key Laboratory of Oral Biomedical Engineering of Higher Education, Chongqing 401147, China)
3. Department of Prosthodontics, West China Hospital of Stomatology, Sichuan University & State Key Laboratory of Oral Diseases & National Clinical Research Center for Oral Diseases, Chengdu 610041, China
4. Department of General Dentistry & Emergency, School of Stomatology, The Fourth Military Medical University & State Key Laboratory of Military Stomatology & National Clinical Research Center for Oral Diseases & Shaanxi International Joint Research Center for Oral Diseases, Xi′an710032, China
- Publication Type:Journal Article
- Keywords:
Tooth preparation;
Post and core technique;
Ferrule;
Fracture resistance
- From:Chinese Journal of Stomatology
2018;53(11):766-770
- CountryChina
- Language:Chinese
-
Abstract:
Objective:To evaluate the influence of fracture resistance of endodontically treated teeth with different thickness of ferrule by mechanical fatigue test and static loading test, and so as to provide a reference for the clinical treatment planning.
Methods:Fifty bovine incisors were divided into 5 groups by random number table method (n=10). Group A was the control group in which the incisors were prepared without a ferrule design (0 mm). The other four groups (B, C, D, E) were experimental groups, and the thickness of the dentin ferrule prepared for specimens in each group was 0.5, 1.0, 1.5, and 2.0 mm. The height of ferrules in all the specimens was 2 mm. Cyclic fatigue loading (2.33 Hz, 50 N) was applied on each specimen until either the specimen was dislodged/fractured or the 300 000 cycles were finished. After fatigue loading, the mode of failure was observed. Those intact specimen after fatigue loading were tested under a gradually increasing force using a universal testing machine (0.05 mm/min) until fracture occurred. The forces required to fracture and failure model was recorded.
Results:The results of cyclic loading tests showed that: all specimens survived the 300 000 cycles of intermittent loading. The results of static loading tests showed that: the fracture force of A, B, C, D and E groups respectively were (226.4±67.7), (369.7±34.5), (400.7±48.2), (528.1±56.3), and (555.4±98.5) N (F=15.227, P=0.000). There was a significant difference in fracture resistance between group A and the other four groups, and between group B, C and group D, E (P<0.05). No statistical difference were found in fracture resistance among the other groups (P>0.05). There was strong correlation between the thickness of ferrule and the fracture force by Pearson correlation analysis (r=0.973, P=0.002).
Conclusions:Within the limitations of this study, the following conclusions can be drawn: The different thickness of ferrule can influence the fracture resistance of the teeth, and when the height of the ferrule is 2.0 mm, the fracture force increased significantly with an increasing ferrule thickness.
