OBJECTIVE: To investigate the biocompatibility of porous WE43 magnesium alloy scaffolds manufactured by 3D printing technology and to observe its effect in treating femoral defects in New Zealand white rabbits. METHODS: In vitro cytotoxicity test was performed using bone marrow mesenchymal stem cells from Sprague Dawley (S-D) rats. According to the different culture media, the cells were divided into 100% extract group, 50% extract group, 10% extract group and control group. After culturing for 1, 3 and 7 days, the cell activity of each group was determined by cell counting kit-8 (CCK-8). In the in vivo experiment, 3.0-3.5 kg New Zealand white rabbits were randomly divided into three groups: Experimental group, bone cement group and blank group, with 9 rabbits in each group. Each rabbit underwent surgery on the left lateral femoral condyle, and a bone defect with a diameter of 5 mm and a depth of 6 mm was created using a bone drill. The experimental group was implanted with WE43 magnesium alloy scaffolds, the bone cement group was implanted with calcium sulfate bone cement, and the blank group was not implanted. Then 4, 8 and 12 weeks after surgery, 3 rabbits in each group were euthanized by carbon dioxide anesthesia, and the femur and important internal organs were sampled. Micro-computed tomography (Micro-CT) scanning was performed on the left lateral femoral condyle. Sections of important internal organs were prepared and stained with hematoxylin-eosin (HE). Hard tissue sections were made from the left lateral femoral condyle and stained with methylene blue acid fuchsin and observed under a microscope. RESULTS: In the cytotoxicity test, the cell survival rate in the 100% extract group was higher than that in the control group (140.56% vs. 100.00%, P < 0.05) on 1 day of culture; there was no statistically significant difference (P>0.05) in cell survival rate among the groups on 3 days of culture; the cell survival rate in the 100% extract group was lower than that in the control group (68.64% vs. 100.00%, P < 0.05) on 7 days of culture. Micro-CT scanning in the in vivo experiment found that most of the scaffolds in the experimental group had been degraded in 4 weeks, with very few high-density scaffolds remaining. In 12 weeks, there was no obvious stent outline. In 4 weeks, a certain amount of gas was generated around the WE43 magnesium alloy scaffold, and the gas was significantly reduced from 8 to 12 weeks. Hard tissue sections showed that a certain amount of extracellular matrix and osteoid were generated around the scaffolds in the experimental group in 4 weeks. In the bone cement group, most of the calcium sulfate bone cement had been degraded. In 8 weeks, the osteoid around the scaffold and its degradation products in the experimental group increased significantly. In 12 weeks, new bone was in contact with the scaffold around the scaffold in the experimental group. There was less new bone in the bone cement group and the blank group. CONCLUSION The porous WE43 magnesium alloy scaffold fabricated by 3D printing process has good biocompatibility and good osteogenic properties, and has the potential to become a new material for repairing bone defects.
Animals ; Rabbits ; Printing, Three-Dimensional ; Alloys/chemistry* ; Tissue Scaffolds/chemistry* ; Magnesium/chemistry* ; Rats, Sprague-Dawley ; Biocompatible Materials ; Mesenchymal Stem Cells/cytology* ; Femur/surgery* ; Rats ; Absorbable Implants ; Male ; Bone Regeneration ; Tissue Engineering/methods* ; Cells, Cultured

OBJECTIVES: To analyze bone mass distribution and the factors affecting bone mass in a general Chinese Han cohort undergoing physical examinations at our center. METHODS: We retrospectively collected the data of bone mineral density (BMD) measurements from 30 599 healthy Han Chinese adults (age≥20 years) who underwent dual-energy X-ray absorptiometry scans at our hospital from July, 2013 to July, 2023. Basic parameters including height, body weight, and gender were recorded, and descriptive statistics and correlation analyses were performed using R software. RESULTS: In this cohort, the male individuals had a mean peak BMD of 1.00±0.12 g/cm² in the lumbar vertebrae, 0.94±0.14 g/cm² in the femoral neck, and 0.99±0.13 g/cm² in the total hip, significantly higher than the values in the female individuals [0.99±0.12 g/cm² in the lumbar vertebrae (P=0.022), 0.79±0.11 g/cm² in the femoral neck (P<0.001), and 0.88±0.11 g/cm² in the total hip (P<0.001)]. In the overall cohort, the BMD values of the lumbar spine and femur decreased with age after reaching their peak levels. There was a positive correlation between BMD value and body mass index (BMI) in both male and female individuals. The 2013-2014 period recorded the lowest BMD values in the lumbar, hip, and femoral neck, which tended to increase steadily in the following years (2015-2023). CONCLUSIONS Our data suggest that the BMD values vary among different populations, and future multi-center studies using more accurate BMD detection technology are warranted to capture the variation patterns of BMD with demographic characteristics of specific populations.
Humans ; Bone Density ; Absorptiometry, Photon ; Male ; Female ; Retrospective Studies ; Osteoporosis/diagnostic imaging* ; Adult ; Middle Aged ; Lumbar Vertebrae/diagnostic imaging* ; China/epidemiology* ; Femur Neck/diagnostic imaging* ; Aged ; Beijing/epidemiology* ; Young Adult

Greater trochanteric pain syndrome(GTPS)is a disease caused by structural lesions of the muscles,fascia,ligaments,and bursae near the greater trochanter of the femur.GTPS causes lateral hip joint pain,severely affecting patients' quality of life.Ultrasound has many advantages,such as real-time diagnosis,portable operation,non-radiation,and high resolution,demonstrating a high application value in the diagnosis and interventional therapy of GTPS.This article reviews the current status of ultrasound in the diagnosis and interventional therapy of GTPS and prospects its application.
Humans ; Ultrasonography ; Femur/diagnostic imaging* ; Hip Joint/diagnostic imaging* ; Arthralgia/therapy*

Steroid-induced osteonecrosis of femoral head (SONFH) is a disease characterized by femoral head collapse and local pain caused by excessive use of glucocorticoids. Peroxisome proliferator-activated receptor-γ (PPARγ) is mainly expressed in adipose tissue. Wnt/β-catenin, AMPK and other related signaling pathways play an important role in regulating adipocyte differentiation, fatty acid uptake and storage. Bone marrow mesenchymal cells (BMSCs) have the ability to differentiate into adipocytes or osteoblasts, and the use of hormones upregulates PPARγ expression, resulting in BMSCs biased towards adipogenic differentiation. The increase of adipocytes affects the blood supply and metabolism of the femoral head, and the decrease of osteoblasts leads to the loss of trabecular bone, which eventually leads to partial or total ischemic necrosis and collapse of the femoral head. MicroRNAs (miRNAs) are a class of short non-coding RNAs that regulate gene expression by inhibiting the transcription or translation of target genes, thereby affecting cell function and disease progression. Studies have shown that miRNAs affect the progression of SONFH by regulating PPARγ lipid metabolism-related signaling pathways. Therefore, it may be an accurate and feasible SONFH treatment strategy to regulate adipogenic-osteoblast differentiation in BMSCs by targeted intervention of miRNA differential expression to improve lipid metabolism. In this paper, the miRNA-mediated PPARγ-related signaling pathways were classified and summarized to clarify their effects on lipid metabolism in SONFH, providing a theoretical reference for miRNA targeted therapy of SONFH, and then providing scientific evidence for SONFH precision medicine.
MicroRNAs/physiology* ; PPAR gamma/metabolism* ; Femur Head Necrosis/metabolism* ; Humans ; Signal Transduction/physiology* ; Lipid Metabolism/physiology* ; Animals ; Cell Differentiation ; Mesenchymal Stem Cells/cytology* ; Glucocorticoids/adverse effects*

This study aims to investigate the pharmacological effects and mechanisms of Yougui Yin in treating glucocorticoid-induced osteonecrosis. A rat model of glucocorticoid-associated osteonecrosis of the femoral head(GA-ONFH) was established by intramuscular injection of dexamethasone at 20 mg·kg~(-1) every other day for 8 weeks. Rats were randomly allocated into control, model, and low-and high-dose(1.5 and 3.0 g·kg~(-1), respectively) Yougui Yin groups. After modeling, rats in Yougui Yin groups were administrated with Yougui Yin via gavage, which was followed by femoral specimen collection. Hematoxylin-eosin staining was employed to observe femoral head repair, and immunofluorescence was employed to assess adipogenic differentiation of bone marrow mesenchymal stem cells(BMSCs) within the femoral head. Cell experiments were carried out with dexamethasone(1 μmol·L~(-1))-treated BMSCs to evaluate the effects of Yougui Yin-medicated serum on adipogenic differentiation. Animal experiments demonstrated that compared with the model group, Yougui Yin at both high and low doses significantly improved bone mineral density(BMD), bone volume/total volume(BV/TV) ratio, and trabecular thickness(Tb.Th) in the femoral head. Additionally, Yougui Yin alleviated necrosis-like changes and adipocyte infiltration and significantly reduced the expression level of peroxisome proliferator-activated receptor γ(PPARγ) in the femoral head, thereby suppressing the adipogenic differentiation of BMSCs in GA-ONFH rats. The cell experiments revealed that Yougui Yin-medicated serum markedly inhibited dexamethasone-induced adipogenic differentiation of BMSCs and down-regulated the level of PPARγ. The overexpression of PPARγ attenuated the inhibitory effect of Yougui Yin-medicated serum on the adipogenic differentiation of BMSCs, indicating the critical role of PPARγ in Yougui Yin-mediated suppression of adipogenic differentiation of BMSCs. In conclusion, Yougui Yin exerts therapeutic effects on glucocorticoid-induced osteonecrosis by down-regulating PPARγ expression and inhibiting adipogenic differentiation of BMSCs.
Animals ; Mesenchymal Stem Cells/metabolism* ; PPAR gamma/genetics* ; Rats ; Drugs, Chinese Herbal/administration & dosage* ; Male ; Glucocorticoids/adverse effects* ; Rats, Sprague-Dawley ; Adipogenesis/drug effects* ; Osteonecrosis/genetics* ; Cell Differentiation/drug effects* ; Bone Marrow Cells/metabolism* ; Femur Head Necrosis/chemically induced* ; Humans

Prosthesis loosening is the leading cause of postoperative revision in unicompartmental knee arthroplasty (UKA). The deviation of medial and lateral translational installation of the prosthesis during surgery is a common clinical phenomenon and an important factor in increasing the risk of prosthesis loosening. This study established a UKA finite element model and a bone-prosthesis fixation interface micromotion prediction model. The predicted medial contact force and joint motion of the knee joint from a patient-specific lower extremity musculoskeletal multibody dynamics model of UKA were used as boundary conditions. The effects of 9 femoral component medial and lateral translational installation deviations on the Von Mises stress of the proximal tibia, the contact stress, and the micro-motion of the bone prosthesis fixation interface were quantitatively studied. It was found that compared with the neutral position (a/A of 0.492), the lateral translational deviation of the femoral component significantly increased the tibial Von Mises stress and the bone-prosthesis fixation interface contact stress. The maximum Von Mises stress and the maximum contact stress of the fixation interface increased by 14.08% and 143.15%, respectively, when a/A was 0.361. The medial translational deviation of the femoral component significantly increased the bone-prosthesis fixation interface micro-motion. The maximum value of micromotion under the conditions of femoral neutral and medial translation deviation was in the range of 20-50 μm, which is suitable for osseointegration. Therefore, based on considerations such as the micromotion range suitable for osseointegration reported in the literature, the risk of reducing prosthesis loosening, and factors that may induce pain, it is recommended that clinicians control the mounting position of the femoral component during surgery within the safe range of 0-4 mm medial translation deviation.
Humans ; Arthroplasty, Replacement, Knee/methods* ; Finite Element Analysis ; Biomechanical Phenomena ; Knee Prosthesis ; Tibia/surgery* ; Femur/surgery* ; Stress, Mechanical ; Prosthesis Failure ; Knee Joint/surgery* ; Prosthesis Design

OBJECTIVE: To explore the advantages and effectiveness of the independently developed intelligent orthopedic robot-assisted distal locking of femoral intramedullary nails. METHODS: Thirty-two adult cadaveric femur specimens were randomly divided into two groups, with 16 specimens in each group. The experimental group used the intelligent orthopedic robot to assist in the distal locking of femoral intramedullary nail holes, while the control group used the traditional method of manual locking under X-ray fluoroscopy. The locking time, fluoroscopy times, and the success rate of first locking were recorded and compared between the two groups. RESULTS: The locking time of the experimental group was (273.94±38.67) seconds, which was shorter than that of the control group [(378.38±152.72) seconds], and number of fluoroscopies was (4.56±0.81) times, which was less than that of the control group [(8.00±3.98) times]. The differences were significant [ MD=73.054 (-37.187, 85.813), P=0.049; MD=1.969 (-1.437, 2.563), P=0.002]. The first locking success rate of the experimental group was 100% (16/16), which was significantly higher than that of the control group (68.75%, 11/16) ( P=0.043). CONCLUSION The efficiency of distal locking of femoral intramedullary nails assisted by the intelligent orthopedic robot is significantly higher than that of the traditional manual locking method under fluoroscopy, as it can markedly reduce the time required for distal locking of femoral intramedullary nails, decrease intraoperative radiation exposure, and increase the success rate of locking.
Humans ; Fracture Fixation, Intramedullary/instrumentation* ; Bone Nails ; Fluoroscopy ; Femur/diagnostic imaging* ; Femoral Fractures/surgery* ; Robotic Surgical Procedures/instrumentation* ; Cadaver ; Adult ; Robotics ; Male

OBJECTIVE: To investigate the effectiveness of digital three-dimensional (3D) printing osteotomy guide plate assisted total knee arthroplasty (TKA) in treatment of knee osteoarthritis (KOA) patients with femoral internal implants. METHODS: The clinical data of 55 KOA patients who met the selection criteria between July 2021 and October 2023 were retrospectively analyzed. Among them, 26 cases combined with femoral implants were treated with digital 3D printing osteotomy guide plate assisted TKA (guide plate group), and 29 cases were treated with conventional TKA (control group). There was no significant difference in gender, age, body mass index, side, Kellgren-Lawrence classification, preoperative visual analogue scale (VAS) score, Hospital for Special Surgery (HSS) knee score, knee range of motion, and other baseline data between the two groups ( P>0.05). The operation time, intraoperative blood loss, incision length, postoperative first ambulation time, surgical complications; VAS score, knee HSS score, knee range of motion before operation, at 1 week and 3 months after operation, and at last follow-up; distal femoral lateral angle, proximal tibial medial angle, hip-knee-ankle angle and other imaging indicators at last follow-up were recorded and compared between the two groups. RESULTS: The operation time, incision length, intraoperative blood loss, and postoperative first ambulation time in the guide plate group were significantly lower than those in the control group ( P<0.05). In the control group, there were 1 case of incision rupture and bleeding and 1 case of lower limb intermuscular venous thrombosis, which was cured after symptomatic treatment. There was no complication such as neurovascular injury, incision infection, or knee prosthesis loosening in both groups. Patients in both groups were followed up 12-26 months, with an average of 16.25 months. The VAS score, HSS score, and knee range of motion improved at each time point after operation in both groups, and further improved with time after operation, the differences were significant ( P<0.05). The above indicators in the guide plate group were significantly better than those in the control group at 1 week and 3 months after operation ( P<0.05), and there was no significant difference between the two groups at last follow-up ( P>0.05). At last follow-up, the distal femoral lateral angle, the proximal tibial medial angle, and the hip-knee-ankle angle in the guide plate group were significantly better than those in the control group ( P<0.05). CONCLUSION The application of digital 3D printing osteotomy guide plate assisted TKA in the treatment of KOA patients with femoral implants can simplify the surgical procedures, overcome limitations of conventional osteotomy guides, reduce surgical trauma, achieve individualized and precise osteotomy, and effectively restore lower limb alignment and knee joint function.
Humans ; Arthroplasty, Replacement, Knee/instrumentation* ; Osteoarthritis, Knee/surgery* ; Osteotomy/instrumentation* ; Male ; Retrospective Studies ; Female ; Printing, Three-Dimensional ; Femur/surgery* ; Middle Aged ; Bone Plates ; Range of Motion, Articular ; Aged ; Treatment Outcome ; Surgery, Computer-Assisted/methods* ; Knee Prosthesis ; Knee Joint/surgery* ; Operative Time

OBJECTIVE: To evaluate precise assessment methods for predicting the optimal acetabular cup size in total hip arthroplasty (THA). METHODS: A clinical data of 73 patients (80 hips) who underwent primary THA between December 2022 and July 2024 and met the inclusion criteria was analyzed. There were 39 males and 34 females with an average age of 66.3 years (range, 56-78 years). Among them, 66 cases were unilateral THA and 7 were bilateral THAs. There were 29 patients (34 hips) of osteoarthritis, 35 patients (35 hips) of femoral neck fractures, and 9 patients (11 hips) of osteonecrosis of the femoral head. Based on anteroposterior pelvic X-ray films, three methods were employed to predict acetabular cup size, including preoperative template planning, radiographic femoral head diameter (FHD) measurement, and intraoperative FHD measurement. The predicted acetabular cup sizes from these methods were compared with the actual implanted sizes. RESULTS: The predicted acetabular cup sizes using the preoperative template planning, radiographic FHD measurement, and intraoperative FHD measurement were (51.25±2.81), (49.72±3.11), and (49.90±2.74) mm, respectively, compared to the actual implanted cup size of (50.57±2.74) mm, with no significant difference ( P>0.05). Regarding agreement with the actual implanted cup size, the preoperative template planning achieved exact matches in 35 hips (43.75%), one-size deviation in 41 hips (51.25%), and two-size deviations in 4 hips (5%); the radiographic FHD measurement achieved exact matches in 12 hips (15%), one-size deviation in 57 hips (71.25%), and two-size deviations in 11 hips (13.75%); and the intraoperative FHD measurement achieved exact matches in 26 hips (32.5%), one-size deviation in 52 hips (65%), and two-size deviations in 2 hips (2.5%). There were significant differences in agreement distributions between the three methods and the actual implanted cup sizes ( H=18.579, P<0.001). CONCLUSION The intraoperative FHD measurement, as a simple, cost-effective, and accurate method, effectively guides acetabular cup selection, reduces the risk of prosthesis wear, enhances postoperative joint stability.
Humans ; Arthroplasty, Replacement, Hip/instrumentation* ; Male ; Female ; Middle Aged ; Acetabulum/diagnostic imaging* ; Aged ; Hip Prosthesis ; Prosthesis Design ; Femur Head/surgery* ; Osteoarthritis, Hip/surgery* ; Radiography ; Femoral Neck Fractures/surgery* ; Femur Head Necrosis/surgery*

OBJECTIVE: To investigate the effectiveness of Salter osteotomy combined with subtrochanteric shortening and derotational osteotomy in treating Tönnis type Ⅲ and Ⅳ developmental dysplasia of the hip (DDH) in children and explore the urgical timing. METHODS: A retrospective collection was performed for 74 children with Tönnis type Ⅲ and Ⅳ DDH who were admitted between January 2018 and January 2020 and met the selection criteria, all of whom were treated with Salter osteotomy combined with subtrochanteric shortening and derotational osteotomy. Among them, there were 38 cases in the toddler group (age, 18-36 months) and 36 cases in the preschool group (age, 36-72 months). There was a significant difference in age between the two groups ( P<0.05), and there was no significant difference in gender, side, Tönnis typing, and preoperative acetabular index (AI) ( P>0.05). During follow-up, hip function was assessed according to the Mckay grade criteria; X-ray films were taken to observe the healing of osteotomy, measure the AI, evaluate the hip imaging morphology according to Severin classification, and assess the occurrence of osteonecrosis of the femoral head (ONFH) according to Kalamchi-MacEwen (K&M) classification criteria. RESULTS: All operations of both groups were successfully completed, and the incisions healed by first intention. All children were followed up 14-53 months, with an average of 27.9 months. There was no significant difference in the follow-up time between the two groups ( P>0.05). At last follow-up, the excellent and good rates according to the Mckay grading were 94.73% (36/38) in the toddler group and 83.33% (30/36) in the preschool group, and the difference between the two groups was significant ( P<0.05). The imaging reexamination showed that all osteotomies healed with no significant difference in the healing time between the two groups ( P>0.05). There was no significant difference in AI between the two groups at each time point after operation ( P>0.05), and the AI in the two groups showed a significant decreasing trend with time extension ( P<0.05). The result of Severin classification in the toddler group was better than that in the preschool group at last follow-up ( P<0.05). There was no significant difference in the incidence of ONFH between the two groups ( P>0.05). In the toddler group, 2 cases were K&M type Ⅰ; in the preschool group, 3 were type Ⅰ, and 1 type Ⅱ. There was no dislocation after operation. CONCLUSION Salter osteotomy combined with subtrochanteric shortening and derotational osteotomy is an effective way to treat Tönnis type Ⅲ and Ⅳ DDH in children, and surgical interventions for children aged 18-36 months can achieve better results.
Humans ; Osteotomy/methods* ; Developmental Dysplasia of the Hip/diagnostic imaging* ; Retrospective Studies ; Male ; Child, Preschool ; Female ; Infant ; Femur/surgery* ; Child ; Treatment Outcome ; Hip Dislocation, Congenital/surgery*